In the PRI detector, after the current radar pulse
has been checked agains existing PRI sequences, it
is considered as part of a new potential sequence.

Previously, the condition to accept a new sequence
was to have at least the same number of pulses as
the longest matching sequence. This was wrong,
since it led to duplicates of PRI sequences.

This patch changes the acceptance criteria for new
potential sequences from 'at least' to 'more than'
the longest existing.

Detection performance remains unaffected, while
the number of PRI sequences accounted at runtime
(and with it CPU load) is reduced by up to 50%.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Reuse existing function ath10k_wmi_op_pull_rdy_ev()
to parse WMI_10_4_READY_EVENTID and handle the same
event in ath10k_wmi_10_4_op_rx().
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware supports upto 512 clients when qcache feature is enabled.
Make adjustment on default max peer count, active peers, number of tid in
such case to meet qcache requirement. 10.4 fw has extra unit info flag
NUM_UNITS_IS_NUM_ACTIVE_PEERS which is also handled in this patch.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware wmi mgmt rx event format differs from non 10.4
firmware and changing existing wmi mgmt rx event parsing function
ath10k_wmi_op_pull_mgmt_rx_ev() for 10.4 would add more complex.

This patch adds new function to receive any wmi rx event from
10.4 firmware and also introduce new function to parse wmi mgmt
rx event.

In addition, fw main branch service rdy event parsing function
is linked in wmi ops table.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Define 10.4 wmi init command structure and introduce new function
ath10k_wmi_10_4_op_gen_init() to fill default values for each field
which goes as part of wmi init cmd to 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Include 10.4 firmware wmi pdev cmd id and prepare wmi vdev map
table wmi_10_4_pdev_param_map and update non 10.4 firmware
pdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Include 10.4 firmware wmi vdev cmd id and make up wmi vdev map
table wmi_10_4_vdev_param_map and also update non 10.4 firmware
vdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In fact, explicit assigned to ZERO for unsupported wmi commands
are not really needed. Global static variable will have ZERO by
default. However, just for better readability setting all wmi cmds
in non 10.4 firmware wmi mapping table as unsupported for wmi cmd
which are exclusively available only in 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 firmware wmi cmd and event id values are not exactly aligned
with previous firmware versions (main, 10.x, 10.2, etc). Add new
enum to define wmi cmd & event definitions for 10.4 firmware and
prepare wmi_10_4_cmd_map based on 10.4 firmware wmi cmd definitions.

wmi_cmd_map is extended to accommodate new wmi commands which are
exclusively available in 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Include new enum to define wmi service bitmap definitions for
10.4 firmware and a function wmi_10_4_svc_map() to remap 10.4
firmware wmi service bitmap definitions to ath10k generic wmi
services.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca99X0 chip uses firmware version 10.4. Define a new macro
ATH10K_FW_WMI_OP_VERSION_10_4 for 10.4 firmware and include
in switch cases where ATH10K_FW_WMI_OP_VERSION_* is used
to avoid compilation error.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

BMI parameter value to execute downloaded otp binary
is different for QCA99X0. Have a member in hw_params
to hold hw specific BMI param.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Code swap is a mechanism to use host memory to store
some fw binary code segment. Ath10k host driver allocates
and loads the code swap binary into the host memory and
configures the target with the host allocated memory
information at the address taken from code swap binary.
This patch adds code swap support for firmware binary.
Code swap binary for firmware bin is available in
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is more than 1 sec delay in getting response from target
through BMI in QCA99X0. Increase the BMI communication timeout
to 2*HZ to fix BMI failures.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 uses two new copy engine src desc flags for interrupt
indication. Bit_2 is to mark if host interrupt is disabled after
processing the current desc and bit_3 is to mark if target interrupt
is diabled after the processing of current descriptor.
CE_DESC_FLAGS_META_DATA_MASK and CE_DESC_FLAGS_META_DATA_LSB are based
on the target type.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 supports only cold reset. Also, made
ath10k_pci_irq_msi_fw_mask() and ath10k_pci_irq_msi_fw_unmask()
non-99X0 specific till we get proper register configuration
to mask/unmask irq/MSI.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make the helper converting target virtual address space to CE address
space a target type specific to support QCA99X0. Also make this as
function instead of macro.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA99X0 supports upto 12 Copy engines. Host and target
CE configuration table is updated to support new copy engine
pipes. This also fixes the assumption of diagnostic CE by making
CE_7 as the one instead of CE_COUNT - 1.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add more register address and mask which can be different
for newer chip to hw_reg table.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wait_event_timeout(), introduced in 'commit 5e3dd157 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is == 0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wait_event_timeout(), introduced in 'commit 5e3dd157 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is ==0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Just found this during code review.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was possible to force an out of bounds MMIO
read/write via debugfs. E.g. on QCA988X this could
be triggered with:

 echo 0x2080e0 | tee /sys/kernel/debug/ieee80211/*/ath10k/reg_addr
 cat /sys/kernel/debug/ieee80211/*/ath10k/reg_value

 BUG: unable to handle kernel paging request at ffffc90001e080e0
 IP: [<ffffffff8135c860>] ioread32+0x40/0x50
 ...
 Call Trace:
  [<ffffffffa00d0c7f>] ? ath10k_pci_read32+0x4f/0x70 [ath10k_pci]
  [<ffffffffa0080f50>] ath10k_reg_value_read+0x90/0xf0 [ath10k_core]
  [<ffffffff8115c2c1>] ? handle_mm_fault+0xa91/0x1050
  [<ffffffff81189758>] __vfs_read+0x28/0xe0
  [<ffffffff812e4694>] ? security_file_permission+0x84/0xa0
  [<ffffffff81189ce3>] ? rw_verify_area+0x53/0x100
  [<ffffffff81189e1a>] vfs_read+0x8a/0x140
  [<ffffffff8118acb9>] SyS_read+0x49/0xb0
  [<ffffffff8104e39c>] ? trace_do_page_fault+0x3c/0xc0
  [<ffffffff8196596e>] system_call_fastpath+0x12/0x71
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable VHT support for IBSS, while mac80211/cfg80211 and
wpa_supplicant already support this.

In my test env, qca988x 2x2 I get:

(udp) ath10k-1 >>>> ath10k-2 (server) -  speed: 419 Mbits/sec
(tcp) ath10k-1 >>>> ath10k-2 (server) -  speed: 404 Mbits/sec

During tests I used wpa_supplicant (latest git version), which
already support IBSS VHT, and choose highest available BW. Also tested with
qca6174.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT version itself isn't sufficient to know what
HTT version given firmware blob uses. Hence print
the recently introduced HTT op version code.

While at it make the info string a bit more
consistent and clear.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This should help when analysing problems from
users and spot fw api blob problems easier.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Major changes:

wil6210:

* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats

On some hardware reading WCID entries table results getting 0xff
numbers, no matter of value written there before. This cause assigning
the same WCID for different stations and makes not possible to connect
to more than one station.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When unloading the driver with a p2pdev interface it resulted in
a warning upon calling wiphy_unregister() and subsequently a crash
in the driver. This patch assures the p2pdev is unregistered calling
unregister_wdev() before doing the wiphy_unregister().
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Moving two functions in p2p.c as is so next change will be
easier to review.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Making it more clear by freeing the ifp in same place where the
vif object is freed.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The bus interface functions txctl and rxctl may be used while the device
can not be accessed, eg. upon driver .remove() callback. This patch will
immediately return -EIO when this is the case which speeds up the module
unload.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The .get_station() cfg80211 callback is used in several scenarios. In
managed mode it can obtain information about the access-point and its
BSS parameters. In managed mode it can also obtain information about
TDLS peers. In AP mode it can obtain information about connected
clients.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Switch from using semi hard coded interface combinations. This makes
it easier to announce what the firmware actually supports. This fixes
the case where brcmfmac announces p2p but the firmware doesn't
support it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NPontus Fuchs <pontusf@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add a feature flag to reflect the firmware's p2p capability.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NPontus Fuchs <pontusf@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We expect EEPROM per-rate power table to be filled with
s6 values and warn user if values are invalid.  However,
there appear to be devices which don't have this section
of EEPROM initialized.  In such case we should ignore
the values and leave the driver power tables set to zero.

Note that vendor driver doesn't care about this case but
mt76x2 skips 0xff per value.  We take mt76x2's approach.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

rt2x00.serialmonkey.com will be shutdown.

Since traffic on rt2x00 mailing list is very low, we can use only
linux-wireless list for any rt2x00 related topics.

Thanks for Luis Correia, Ivo van Doorn and Mark Wallis for maintaining
rt2x00 servers for years!
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.
Signed-off-by: NChunfan Chen <jeffc@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>