Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

IP32 doesn't even have a ZONE_DMA so no point in using GFP_DMA in any
IP32-specific device driver.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As noticed by Chuck Ebbert, commit c5e3ae88
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch addresses the issue with "osize too small" errors in mppe
encryption.  The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.

--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: NKonstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ.  It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.

This patch moves the printk's out of the spinlock protected area.

Without this patch the machine hangs hard.  With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: NTimo Jantunen <jeti@iki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (edited MACINTOSH_DRIVERS per Geert Uytterhoeven's remark)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.

For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set.  If both have TSO then this produces
an illegal combination.

The bridge device on the other hand has the correct code to
deal with this.

In fact, the same code can be used for both.  So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.

In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 drivers/net/irda/irda-usb.c | 59694 -> 59541 (-153 bytes)
 drivers/net/irda/irda-usb.o | 170588 -> 169256 (-1332 bytes)
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 drivers/net/wan/hdlc_fr.c | 31260 -> 31223 (-37 bytes)
 drivers/net/wan/hdlc_fr.o | 144872 -> 144728 (-144 bytes)
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

xennet_tx_bug_gc can free the skb before we use it, so make sure we don't.
Signed-off-by: NKeir Fraser <keir@xensource.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A special sequence of ifconfig up/down and plug/unplug the cable can break
the duplex configuration of the driver.

Setting
vp->mii.full_duplex = vp->full_duplex
in vortex_up should fix this.

Addresses Bug 8575 3c59x duplex configuration broken
http://bugzilla.kernel.org/show_bug.cgi?id=8575

Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org>
Signed-off-by: NSteffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When a detailed netdev error is counted, we also must account for it in the
aggregated error count.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8106

Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Chongfeng Hu <loveminix@yahoo.com.cn>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/net/ax88796.c: In function `ax_probe':
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 4)
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 5)

resource_size_t isn't size_t.

Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use the pause counter to avoid a needless device reset, and
print a message telling the admin that our link partner is
flow controlling us down to 0 pkts/sec.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Patch to disable the rx_copybreak feature on hardware architectures that
don't allow unaligned DMA access.

#ifdef code taken from tulip_core.c.  Problem pointed out by Ivan
Kokshaysky.
Signed-off-by: NDustin Marquess <jailbird@alcatraz.fdf.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Put a 1000 msec delay after resetting the device before attempting to
do config cycles on it.  Not waiting causes system hangs on some
chipsets, e.g. Intel E7520, when the driver is loaded.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

> >> 	Looks like memset() is zeroing wrong nr of bytes.
> >
> > Good catch, however, I think we can just remove this memset altogether
> > since the memory gets allocated via kzalloc.
>
> Correct, that memset() is superfluous.

Ok. Then this should do it.
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>

 drivers/net/ibmveth.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix a thinko (?) in setting phydev->autoneg.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixed wrongly casted pointers
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use shorter method to determine whether adapter has configured ports
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix: Workqueue ehea_driver_wq was not destroyed
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This fixes the following oops which can occur when trying to deallocate
receive buffer pools using sysfs with the ibmveth driver.

NIP: d00000000024f954 LR: d00000000024fa58 CTR: c0000000000d7478
REGS: c00000000ffef9f0 TRAP: 0300   Not tainted  (2.6.22-ppc64)
MSR: 8000000000009032 <EE,ME,IR,DR>  CR: 24242442  XER: 00000010
DAR: 00000000000007f0, DSISR: 0000000042000000
TASK = c000000002f91360[2967] 'bash' THREAD: c00000001398c000 CPU: 2
GPR00: 0000000000000000 c00000000ffefc70 d000000000262d30 c00000001c4087a0
GPR04: 00000003000000fe 0000000000000000 000000000000000f c000000000579d80
GPR08: 0000000000365688 c00000001c408998 00000000000007f0 0000000000000000
GPR12: d000000000251e88 c000000000579d80 00000000200957ec 0000000000000000
GPR16: 00000000100b8808 00000000100feb30 0000000000000000 0000000010084828
GPR20: 0000000000000000 000000001014d4d0 0000000000000010 c00000000ffefeb0
GPR24: c00000001c408000 0000000000000000 c00000001c408000 00000000ffffb054
GPR28: 00000000000000fe 0000000000000003 d000000000262700 c00000001c4087a0
NIP [d00000000024f954] .ibmveth_remove_buffer_from_pool+0x38/0x108 [ibmveth]
LR [d00000000024fa58] .ibmveth_rxq_harvest_buffer+0x34/0x78 [ibmveth]
Call Trace:
[c00000000ffefc70] [c0000000000280a8] .dma_iommu_unmap_single+0x14/0x28 (unreliable)
[c00000000ffefd00] [d00000000024fa58] .ibmveth_rxq_harvest_buffer+0x34/0x78 [ibmveth]
[c00000000ffefd80] [d000000000250e40] .ibmveth_poll+0xd8/0x434 [ibmveth]
[c00000000ffefe40] [c00000000032da8c] .net_rx_action+0xdc/0x248
[c00000000ffefef0] [c000000000068b4c] .__do_softirq+0xa8/0x164
[c00000000ffeff90] [c00000000002789c] .call_do_softirq+0x14/0x24
[c00000001398f6f0] [c00000000000c04c] .do_softirq+0x68/0xac
[c00000001398f780] [c000000000068ca0] .irq_exit+0x54/0x6c
[c00000001398f800] [c00000000000c8e4] .do_IRQ+0x170/0x1ac
[c00000001398f890] [c000000000004790] hardware_interrupt_entry+0x18/0x1c
   Exception: 501 at .plpar_hcall_norets+0x24/0x94
    LR = .veth_pool_store+0x15c/0x298 [ibmveth]
[c00000001398fb80] [d000000000250b2c] .veth_pool_store+0x5c/0x298 [ibmveth] (unreliable)
[c00000001398fc30] [c000000000145530] .sysfs_write_file+0x140/0x1d8
[c00000001398fcf0] [c0000000000de89c] .vfs_write+0x120/0x208
[c00000001398fd90] [c0000000000df2c8] .sys_write+0x4c/0x8c
[c00000001398fe30] [c0000000000086ac] syscall_exit+0x0/0x40
Instruction dump:
fba1ffe8 fbe1fff8 789d0022 f8010010 f821ff71 789c0020 1d3d00a8 7b8a1f24
38000000 7c7f1b78 7d291a14 e9690128 <7c0a592a> e8030000 e9690120 80a90100
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sis190 driver assumes to find ISA only on SiS965.
similar fix is in sis900 driver, see bug report
http://bugs.debian.org/435547Signed-off-by: Nmaximilian attems <max@stro.at>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

use the simpler spin_trylock_irqsave() API to get the adapter lock.

[ this is also a fix for -rt where adapter->lock is a sleeping lock. ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

SH boards in general only wire this up in 8 or 16-bit mode, and
as we never had the wrappers for 32-bit mode defined, SMC_CAN_USE_32BIT
caused build failure for the non-Solution Engine boards. This gets it
building again.

Also kill off the straggling set_irq_type() definition, this is left
over cruft that was missed when the rest of it switched to IRQ flags.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

--

 drivers/net/smc91x.h |    4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Theory  : though needless, it should not have hurt.
Practice: it does not play nice with DEBUG_SHIRQ + LOCKDEP + UP
(see https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242572).

The patch makes sense in itself but I should dig why it has an effect
on #242572 (assuming that NAPI do not change in a near future).
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>

Fix extracted from Realtek's driver (8.002.00/20070713) for the PHY
attached to 8111/8168b chipsets.

The check against mac_version is just usual paranoia during the bugfix
period of the kernel cycle. -- FR

Tested on Asus M2A-VM motherboard by Roger So.
No regression on my Asrock 945G DVI either (built-in 8168 + 2x8169).
Signed-off-by: NRoger So <roger.so@gmail.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>

While filling the control set the driver tests for a PSPOLL frame.
But it tested only the subtype of the packet. The full type needs
to be tested to identify those packets reliably.

[dsd@gentoo.org: backport to mainline]
Signed-off-by: NUlrich Kunitz <kune@deine-taler.de>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

conf->mac_addr is not guaranteed to be set. This ensures priv->hwaddr is
always set to a valid mac address. Thanks to Johannes Berg
<johannes@sipsolutions.net> for finding this problem.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 77548f58.

David Woodhouse wrote:

>This broke my shinybook. I seem to get absolutely _no_ outgoing packets,
>although I can receive OK.

Larry Finger wrote:

>Please revert this patch.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device would not resume properly if it was shutdown before the system
was suspended.  In such scenario where the netif_running state is 0,
bnx2_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.

We fix this by always saving and restoring the PCI state in
bnx2_suspend() and bnx2_resume() regardless of netif_running() state.

Update version to 1.6.4.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended.  In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.

We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 * wrong argument passed to pci_unmap_single() on failure
   exit paths
 * leak in the same area
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is needed because commit 313674af
inlines the generic function to the caller.
Signed-off-by: NJan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: NLi Yang <leoli@freescale.com>

This fix section mismatch:
reference to .exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')

void __exit uec_mdio_exit(void) is called from
- static int __init ucc_geth_init(void)
- static void __exit ucc_geth_exit(void)

First one would make error path more than just an error.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NLi Yang <leoli@freescale.com>

Typo fixes errror -> error
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>