For nexthop neighbours we need to make kernel to think there is a traffic
flowing to them preventing it from going to stale state. Otherwise
kernel would stale it and eventually the neigh would be removed from HW
and nexthop as well. That would reduce ECMP group in HW.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement next-hop routing offload including ECMP. To make it possible,
introduce next-hop group entity. This entity keeps track of resolved
neighbours and updates HW adjacency table accordingly. Note that HW
next-hops are stored in this adjacency table, in form of MAC.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RALEU register is used to mass update remote action adjacency index
and ecmp size.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RATR register is used to configure the Router Adjacency (next-hop)
Table.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a very simple manager for KVD linear area. Currently, the
allocator will either allocate a single entry from pre-defined sub-area,
or in case more than one entry is needed, it will allocate 32-entry chunk
in other pre-defined sub-area.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Override the defaults and define the area sizes ourselves.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we only used hash-based tables in the device, but we are
going to use the linear table for remote routes adjacency lists.

Add the configuration fields that control the size of the linear table.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Listen to any NEIGH_UPDATE events sent and program the device
accordingly. If NUD state is VALID and neighbour isn't yet offloaded,
then program it into the device's table. Otherwise, just edit its
parameters.

If NUD state machine transitioned neighbour out of VALID state and it's
present in the device's table, then remove it.

Note that the device is programmed in delayed work, as the netevent
notification chain is atomic and prevents us from going to sleep.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As previously explained, the driver should periodically poll the device
for neighbours activity according to the configured DELAY_PROBE_TIME.
This will prevent active neighbours from staying in STALE state for long
periods of time.

During init configure the polling interval according to the
DELAY_PROBE_TIME used in the default table. In addition, register a
netevent notification block, so that the interval is updated whenever
DELAY_PROBE_TIME changes.

Using the computed interval schedule a delayed work, which will update
the kernel via neigh_event_send() on any active neighbour since the last
delayed work.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the data plane is offloaded the traffic doesn't go through the
networking stack. Therefore, after first resolving a neighbour the NUD
state machine will transition it from REACHABLE to STALE until it's
finally deleted by the garbage collector.

To prevent such situations the offloading driver should notify the NUD
state machine on any neighbours that were recently used. The driver's
polling interval should be set so that the NUD state machine can
function as if the traffic wasn't offloaded.

Currently, there are no in-tree drivers that can report confirmation for
a neighbour, but only 'used' indication. Therefore, the polling interval
should be set according to DELAY_FIRST_PROBE_TIME, as a neighbour will
transition from REACHABLE state to DELAY (instead of STALE) if "a packet
was sent within the last DELAY_FIRST_PROBE_TIME seconds" (RFC 4861).

Send a netevent whenever the DELAY_FIRST_PROBE_TIME changes - either via
netlink or sysctl - so that offloading drivers can correctly set their
polling interval.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RAUHTD register allows dumping entries from the Router Unicast Host
Table.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RAUHT register is used to configure and query the Unicast Host Table
in devices that implement the Algorithmic LPM. In other words, it is
used to configure neighbour entries in the device.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to hold some private data for every neigh entry. It would be
possible to do it using neigh_priv_len/ndo_neigh_construct/
ndo_neigh_destroy however only for the port device itself. That would not
work for stacked devices like bridge/team/bond. So introduce a private
neigh table. Hook onto ndos neigh_construct/destroy and add/remove
table entry according to that.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

L2 upper device needs to propagate neigh_construct/destroy calls down to
lower devices. Do this by defining default ndo functions and use them in
team, bond, bridge and vlan.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the following patch will allow upper devices to follow the call down
lower devices, we need to add dev here and not rely on n->dev.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: r6040: Misc updates

Here are some various updates for the r6040 driver, mostly to make it more
modern and catch up with the latest API improvements.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump version to 0.28 and date to 4th of July 2016.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update my email address in the driver and MAINTAINERS file.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We maintain how much work we did in NAPI context, so provide that with
napi_complete_done().
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are already in hard IRQ context, so we can use
__napi_schedule_irqoff() to save a few operations.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kick the transmission only if this is the last SKB to transmit or the
queue is not already stopped.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of taking one interrupt per packet transmitted, re-use the same
NAPI context to free transmitted buffers. Since we are no longer in hard
IRQ context replace dev_kfree_skb_irq() by dev_kfree_skb().
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pad the SKB to the minimum length of ETH_ZLEN by using skb_put_padto()
and take this operation out of the critical section since there is no
need to check any HW resources before doing that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

r6040_xmit() is increasing transmit statistics during transmission while
this may still fail, do this in r6040_tx() where we complete transmitted
buffers instead.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of open coding our own version utilize the library provided
function.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.
Signed-off-by: NWei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 ethtool ntuple steering

This series adds Ethernet ethtool ntuple steering 'ethtool -N|U' and exposes two more
counter sets to Ethtool statistics, RDMA vport and global flow control statistics.

We start from three refactoring patches of the flow steering infrastructure
    - mlx5_add_flow_rule will now receive mlx5 flow spec to simplify and reduce
      number of parameters
    - All low level steering objects are now wrapped in mlx5_flow_steering structure
      for better encapsulation
    - Flow steering object will now be removed properly and generically rather than
      traversing on a well-known steering tree objects

Patch#4 adds the infrastructure and the data structures needed for the ethtool ntuple
steering, all implemented in a new file 'en_fs_ethtool.c'.  Add the support for set_rxnfc
ethtool callback to add/remove/replace a flow spec of ethter type L2.

Patch#5 adds the support for L3/L4 flow specs and a higher priority in favor for L3/L4
rules when interleaving with L2 rules.

Patch#6 adds the support for get_rxnfc ethtool callback.

Patch#7,8 adds RDMA vport and global flow control statistics.

Applied on top: 8186f6e3 ('net-next: mediatek: fix compile error inside mtk_poll_controller()')
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just like per prio counters, the global flow counters are queried from
per priority counters register.
Global flow control counters are stored in priority 0 PFC counters.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the needed descriptors to expose RoCE RDMA counters.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enhance the existing get_rxnfc callback:
1. Get flow rule of specific ID.
2. Get all flow rules.
3. Get number of rules.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to add flow steering rules with ethtool
of L3/L4 flow types (ip4/tcp4/udp4).
Those rules will be in higher priority than l2 flow rules, in order
to prefer more specific rules.

Mask is not supported for l3/l4 flow types.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement etrhtool set_rxnfc callback to support ethtool flow spec
direct steering. This patch adds only the support of ether flow type
spec. L3/L4 flow specs support will be added in downstream patches.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of explicitly cleaning up the well known parts of the steering
tree, we use the generic tree structure to traverse for cleanup.
No functional changes.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having all steering private name spaces and
steering module fields flat in mlx5_core_priv, we wrap
them in mlx5_flow_steering for better modularity and
API exposure.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 80673029 ("net-next: mediatek: add support for IRQ grouping")
adds handling for irq 1 and 2 to the uninit function but did not remove
irq 0 which is not used since irq grouping was introduced. Fix this by
removing the superfluous call to free_irq().
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit f786f356 ("net: ethernet: lpc_eth: use phydev
from struct net_device") the 'pldat' variable became unused, so
just remove it.
Reported-by: NOlof's autobuilder <build@lixom.net>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature patchset includes the following changes:

 - Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)

 - Initial Netlink support by Matthias Schiffer (two patches)

 - Throughput Meter implementation by Antonio Quartulli, a kernel-space
   traffic generator to estimate link speeds. This feature is useful on
   low-end WiFi APs where running iperf or netperf from userspace
   gives wrong results due to heavy userspace/kernelspace overhead.
   (two patches)

 - API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Implement basic FIB offload and router interfaces

Introduce LPM trees management including virtual router management for HW.
Implement basic FIB offloading using switchdev FIB objects. For now only support
local routes and direct routes (next-hop support will be introduced in
a follow-up patchset).

Introduce router interfaces in patches 10-14.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.

The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>