Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.

This fixes display corrupt issue on HP arrandale with new vbios.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.

This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Turns out some machines, like the ThinkPad X40 don't come back if you
don't save/restore this register.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.

This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.

Cc: Stable Team <stable@kernel.org>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: NEric Anholt <eric@anholt.net>

If the device didn't support EDP, we would bail out too soon.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
[anholt: Pulled this patch out of the patch for adding quirks to
enable reclocking.]
Signed-off-by: NEric Anholt <eric@anholt.net>

This hasn't fixed the regressions we were testing against, but clearly
should be required.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).

So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.

At the same time fix the typo error in LVDS center scaling mode.

https://bugs.freedesktop.org/show_bug.cgi?id=23789Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
tested-by: NZhao Jian <jian.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

GFP_ATOMIC without good cause is evil.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:visor: fix race between unthrottle and completion handler

visor_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.

the same bug as opticon.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

many serial subdrivers are clearly written as if throttle/unthrottle
cannot sleep. This leads to unneeded atomic submissions. This
patch converts affected drivers in a way to makes very clear that
throttle/unthrottle can sleep. Thus future misdesigns can be avoided
and efficiency and reliability improved.

This removes any such assumption using GFP_KERNEL and spin_lock_irq()
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:symbolserial: fix race between unthrottle and completion handler

symbol_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.

the same bug as opticon.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:opticon: fix race between unthrottle and completion handler

opticon_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI driver does some bounds checking when it's scheduling an iTD for
an active endpoint.  It sets the local variable start to
stream->next_uframe and moves that variable further in the schedule if
necessary.  However, the driver fails to do anything with start before
jumping to the ready label and setting the URB's starting frame to
stream->next_uframe.  Alan Stern confirms the EHCI driver should set
stream->next_uframe to start before jumping.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1294) fixes a problem that has plagued users for several
kernel releases.  Some USB mass-storage devices don't return any sense
data when they encounter certain kinds of errors.  The SCSI layer
interprets this to mean that the operation should be retried, and the
same thing happens -- over and over again with no limit.  In some
circumstances (such as when a bus reset occurs) that is the right
thing to do, but not here.

The patch checks for this condition (a transport failure with no sense
data) and changes the result code to DID_ERROR and the sense code to
Hardware Error.  This does get only a limited number of retries, and
so the command will fail relatively quickly instead of getting stuck
in an infinite loop.

This fixes a large part of Bugzilla #14118.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NMantas Mikulenas <grawity@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb:usbserial: fix flags in error case of suspension

suspended flag must be reset in error case
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:visor: fix accounting in error case

data not pushed to the tty layer due to an error mustn't be counted
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The generic usbserial driver in Linux 2.6.31 halts its receiving
channel in response to throttle requests from the line discipline.
Unfortunately it drops the contents of the first URB received after
throttling takes effect. This patch corrects that problem.
Signed-off-by: NJoris van Rantwijk <jorispubl@xs4all.nl>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the Dell inspiron mini 10, the GPS is connected via a cp2102. This patch
adds detection of this USB device. (I haven't managed to use the GPS under
Linux yet, though)
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1293) fixes a problem with the ipaq serial driver.  It
tries to bind to all the interfaces, even those that don't have enough
endpoints.  The symptom is an invalid memory reference and oops when
the device is plugged in.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Tested-by: NMatthias Geissert <geissert@mathematik.tu-darmstadt.de>
Tested-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A bunch of places assumed pointers were 32-bits in size (bit checking and
debug output), but none of these affected runtime functionality.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Blackfin port doesn't support HAVE_CLK and the musb driver works fine
with support stubbed out, so take the existing Blackfin clk stubs and move
them to common musb code so we can drop the Kconfig dependency.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When an endpoint is to be dropped from the hardware bandwidth schedule, we
want to clear its add flag.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the host controller dies or is removed while a device is plugged in,
the USB core will attempt to deallocate the struct usb_device.  That will
call into xhci_free_dev().  This function used to attempt to submit a
disable slot command to the host controller and clean up the device
structures when that command returned.  Change xhci_free_dev() to skip the
command submission and just free the memory if the host controller died.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the host controller dies (e.g. it is removed from a PCI card slot),
the xHCI driver cannot expect commands to complete.  The buggy code this
patch fixes would mark an URB as canceled and then expect the URB to be
completed when the stop endpoint command completed.  That would never
happen if the host controller was dead, so the USB core would just hang in
the disconnect code.

If the host controller died, and the driver asks to cancel an URB, free
any structures associated with that URB and immediately give it back.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the host controller card is removed from the system, stop the timer
function to debug the xHCI rings.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current 10ms timeout is too short for some normal USBTMC device
operation, increase it to a value which was tested with previously
affected Tektronix oscilloscopes.
Signed-off-by: NGergely Imreh <imrehg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeter Magdina <peter@magdina.sk>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Stanse found a memory leak in lcd_probe. Instead of returning without
releasing the memory, jump to the error label which frees it.

http://stanse.fi.muni.cz/Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: NElina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method.  This causes some drivers (io_ti in particular) to perform an
invalid memory access.

The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NJean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a regression introduced in
39892da4.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix regression introduced by commit
d4fc4a7b (tty: Fix the PL2303 private
methods for sysrq).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Re-structure read processing.
 - Kill obsolete work queue and always push to tty in completion handler.
 - Use tty_insert_flip_string instead of per character push when
   possible.
 - Fix stalled-read regression in 2.6.31 by using urb status to
   determine when port is closed rather than port count.
 - Fix race with open/close by checking ASYNCB_INITIALIZED in
   unthrottle.
 - Kill private rx_flag and lock and use throttle flags in
   usb_serial_port instead.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>