There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.

This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.

This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.

I am going to chalk this up as a bug and fix it now.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.

There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the queuing that was previously done for L4 packets
as it is not needed. The filter does not provide functionality, and it
is possible that queue setup here could trample settings done else-where
in the driver. (for example it may use a queue which isn't setup.)
Setting of the queue is not required for hardware timestamping and could
have inadverdent side effects.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes a magic number that was used for the ETQF used for
filtering L2 ptp packets and replaces it with the supplied define that
previously existed. The intent is to clarify that this filter is already
set aside for L2 1588 work.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reformats the output of the Tx/Rx descriptor dumps to more
appropriately align the output of the ixgbe_dump and improve readability.
Prevents empty Tx descriptors from being displayed to decrease the size
of the dump and make it more manageable.
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

bnx2x_hsi.h was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides extensions to VXLAN for supporting Distributed
Overlay Virtual Ethernet (DOVE) networks. The patch includes:

	+ a dove flag per VXLAN device to enable DOVE extensions
	+ ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint
		answers ARP requests from the local bridge on behalf of
		remote DOVE clients
	+ route short-circuiting (aka L3 switching). Known destination IP
		addresses use the corresponding destination MAC address for
		switching rather than going to a (possibly remote) router first.
	+ netlink notification messages for forwarding table and L3 switching
		misses

Changes since v2
	- combined bools into "u32 flags"
	- replaced loop with !is_zero_ether_addr()
Signed-off-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Various drivers depend on INET because they used to select INET_LRO,
but they have all been converted to use GRO which has no such
dependency.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2cb1deb5 ('ehea: Remove LRO
support') left behind the Kconfig depends/select and feature flag.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit fa37a958 ('mlx4_en: Moving to
work with GRO') left behind the Kconfig depends/select, some dead
code and comments referring to LRO.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.

With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move to circular buffers management macro and correct an error
with circular buffer initial condition.

Without this patch, the macb_tx_ring_avail() function was
not reporting the proper ring availability at startup:
macb macb: eth0: BUG! Tx Ring full when queue awake!
macb macb: eth0: tx_head = 0, tx_tail = 0
And hanginig forever...

I remove the macb_tx_ring_avail() function and use the
proven macros from circ_buf.h. CIRC_CNT() is used in the
"consumer" part of the driver: macb_tx_interrupt() to match
advice from Documentation/circular-buffers.txt.
Reported-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow an unpriviled user who has created a user namespace, and then
created a network namespace to effectively use the new network
namespace, by reducing capable(CAP_NET_ADMIN) calls to
ns_capable(net->user_ns,CAP_NET_ADMIN) calls.

Allow setting of the tun iff flags.
Allow creating of tun devices.
Allow adding a new queue to a tun device.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NSerge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qlcnic_hw.c:1337:17: warning: cast removes address space of expression
qlcnic_hw.c:1337:17: warning: incorrect type in argument 2 (different address spaces)
qlcnic_hw.c:1337:17:    expected void volatile [noderef] <asn:2>*addr
qlcnic_hw.c:1337:17:    got void *<noident>
qlcnic_hw.c:1337:17: warning: cast removes address space of expression
qlcnic_hw.c:1337:17: warning: incorrect type in argument 1 (different address spaces)
qlcnic_hw.c:1337:17:    expected void const volatile [noderef] <asn:2>*addr
qlcnic_hw.c:1337:17:    got void *<noident>

The above warnings are originating from the macros QLCNIC_RD_DUMP_REG and
QLCNIC_WR_DUMP_REG.
The warnings are fixed and macros are replaced with equivalent functions
in the only file from where it is called.

The following warnings are fixed by making the functions static.

qlcnic_hw.c:543:5: warning: symbol 'qlcnic_set_fw_loopback' was not declared. Should it be static?
qlcnic_init.c:1853:6: warning: symbol 'qlcnic_process_rcv_diag' was not declared. Should it be static?
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following warnings:

qlcnic_main.c: In function 'qlcnic_update_cmd_producer':
qlcnic_main.c:119:51: warning: unused parameter 'adapter' [-Wunused-parameter]
qlcnic_main.c:119: warning: unused parameter adapter
qlcnic_init.c: In function qlcnic_process_lro
qlcnic_init.c:1586: warning: unused parameter sds_ring
qlcnic_init.c: In function qlcnic_process_rcv_diag
qlcnic_init.c:1854: warning: unused parameter sds_ring
qlcnic_init.c: In function qlcnic_fetch_mac
qlcnic_init.c:1938: warning: unused parameter adapter

warning: 'pci_using_dac' may be used uninitialized in this function [-Wmaybe-uninitialized]
qlcnic_main.c:1569:10: note: 'pci_using_dac' was declared here
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit a24006ed ('ptp: Enable clock
drivers along with associated net/PHY drivers') I wrongly made
PTP_1588_CLOCK_PCH depend on PCH_GBE.  The dependency is really the
other way around.  Therefore make PCH_GBE select PTP_1588_CLOCK_PCH
and remove the 'default y' from the latter.
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes addrexceeded member from vxlan_dev struct as it is unused.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simply makes the tilegx net driver call request_irq with a
non-null name. It makes the output in /proc/interrupts more obvious, but
also helps tools that don't expect to find null there.
Signed-off-by: NSimon Marchi <simon.marchi@polymtl.ca>
Acked-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch re-enables Energy Detect Power Down (EDPD) mode for the
LAN8710/LAN8720.  EDPD mode was disabled in a previous commit,
(b629820d), because it was causing the
PHY to not be able to detect a link when cold started without a cable
connected.

The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of
each other in order to set the ENERGYON bit and exit EDPD mode.  If a
link partner does send the pulses within this interval, the PHY will
remained powered down.

This workaround will manually toggle the PHY on/off upon calls to
read_status in order to generate link test pulses if the link is down.
If a link partner is present, it will respond to the pulses, which will
cause the ENERGYON bit to be set and will cause the EDPD mode to be
exited.
Signed-off-by: NPatrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver supports GRCAN and CRHCAN CAN controllers available in the GRLIB
VHDL IP core library.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.

So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: Nliu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch extends the esd_usb2 driver to support the
tiny CAN-USB/Micro CAN/USB interface.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add listen-only mode for esd_usb2 driver.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Patch adds support for CANpro/104-Plus Opto CAN board. Board uses PLX9030
bridge and two NXP SJA1000 CAN controllers. Patch is generated and tested with
kernel 3.6.1.
Signed-off-by: NMuhammad Ghias <mghias@connecttech.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
[mkl: minor adjustments to commit message]
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add hardware checksum statistic counters to the ring structures and
then during packet processing update those counters instead of the
global counters in the adapter structure.  Only update the adapter
structure counters when all other statistics are gathered in the
ixgbevf_update_stats() function.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The spinlocks are not required during reset.  There won't be any
contention for the mailbox resource.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function pointers will always be set - there is no good reason to
check them.  Also just remove get_bus_info() call as the VF has no bus
info to report.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is unused - remove it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove dereference of hw pointer from adapter structure since a pointer
to the hw structure has already been allocated off the stack.  Also clean
up useless parenthesis.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Moves allocation of local variable to section where it is needed and
removes unnecessary if statement.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This reverts commit aa731872.

As pointed out by Ben Hutchings, this change is not correct.

mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.

Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move network stack halt APIs before halting the hardware to ensure no
packets are queued to hardware during closing the device during
suspend sequence.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having a host of different register offsets in the device tree,
this patch simplifies the CPSW code by letting the driver set the proper
register offsets automatically, based on the CPSW version.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPGMAC SubSystem consist of various sub-modules, like, mdio, cpdma,
cpsw, etc... These sub-modules are also used in some of Davinci family
of devices. Now based on requirement, use-case and available technology
nodes the integration of these sub-modules varies across devices.

So coming back to Linux net driver, currently separate and independent
platform devices & drivers for CPSW and MDIO is implemented. In case of
Davinci they both has separate control, from resources perspective,
like clock.

In case of AM33XX, the resources are shared and only one register
bit-field is provided to control module/clock enable/disable, makes it
difficult to handle common resource.

So the solution here implemented in this patch is,

Create parent<->child relationship between both the drivers, making
CPSW as a parent and MDIO as its child and enumerate all the child nodes
under CPSW module.
Both the drivers will function exactly the way it was operating before,
including runtime-pm functionality. No change is required in MDIO driver
(for that matter to any child driver).

As this is only supported during DT boot, the parent<->child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making MDIO as a child to CPSW node.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By mistake (most likely a copy-paste), instead of pm_runtime_get_sync()
api, driver is calling pm_runtime_put_sync() api in resume callback
function. The bug was introduced by commit id (ae2c07aaf74:
davinci_mdio: runtime PM support).

Now, the reason why it didn't impact functionality is, the patch has
been tested on AM335x-EVM and BeagleBone platform while submitting;
and in case of AM335x the MDIO driver doesn't control the module
enable/disable part, which is handled by CPSW driver.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

irq_cnt is no longer reliable since rxq_cnt can be independently configured.

Update version to 3.127.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>