Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.
Signed-off-by: Nfangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:

tty_release: ttyUSB1: read/write wait queue active!

It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.
Signed-off-by: NGustavo Zacarias <gustavo@zacarias.com.ar>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NRui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NAntonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: NPavel Parkhomenko <ra85551@gmail.com>
Tested-by: NPavel Parkhomenko <ra85551@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: Nfangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Hi,

my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn>  (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: NMichal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: Nenrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding support for D-Link DWM-152/C1 and DWM-156/C1 devices.

DWM-152/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e01 Rev= 0.00
S:  Product=USB Configuration
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

DWM-156/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e02 Rev= 0.00
S:  Product=DataCard Device
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: NAlexandr Ivanov <alexandr.sky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch was tested on 3.10.1 kernel.

Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: NDaniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option.  Their
network port is handled by qmi_wwan.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev.  The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.

I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: NGraham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A rebranded Novatel E371 for AT&T's LTE bands.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

/drivers/usb/serial/option.c: Blacklisted Cinterion's PLxx WWAN
Interface (USB Interface 4), because it will be handled by QMI WWAN
driver. Product IDs renamed.
Signed-off-by: NHans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Information from driver description files:

  diag:  VID_19D2&PID_0412&MI_00
  nmea:  VID_19D2&PID_0412&MI_01
  at:    VID_19D2&PID_0412&MI_02
  modem: VID_19D2&PID_0412&MI_03
  net:   VID_19D2&PID_0412&MI_04
Signed-off-by: NTeppo Kotilainen <qubit303@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds PID for Olivetti Olicard 145 in option.c
Signed-off-by: NFilippo Turato <nnj7585@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding support for a Mediatek based device labelled as
D-Link Model: DWM-156, H/W Ver: A7

Also adding two other device IDs found in the Debian(!)
packages included on the embedded device driver CD.

This is a composite MBIM + serial ports + card reader device:

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2001 ProdID=7d01 Rev= 3.00
S:  Manufacturer=D-Link,Inc
S:  Product=D-Link DWM-156
C:* #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=88(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=500us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

add support for Cinterion's products AH6 and PLS8 by adding Product IDs
and USB_DEVICE tuples.
Signed-off-by: NChristian Schmiedl <christian.schmiedl@gemalto.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Another device using CDC ACM with vendor specific protocol to mark
serial functions.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.

The CDC ACM class driver cannot support functions with only 2
endpoints.  The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.

There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface layout:

 00 CD-ROM
 01 debug COM port
 02 AP control port
 03 modem
 04 usb-ethernet

Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0408 ProdID=ea42 Rev= 0.00
S:  Manufacturer=Qualcomm, Incorporated
S:  Product=Qualcomm CDMA Technologies MSM
S:  SerialNumber=353568051xxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

New device with 3 serial interfaces:

 If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend) Sub=ff Prot=ff
 If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
 If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend) Sub=ff Prot=ff
 If#= 3 Alt= 0 #EPs= 2 Cls=08(stor) Sub=06 Prot=50

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PID and special handling for Telit LE920
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding three currently unsupported modems based on information
from .inf driver files:

  Diag  VID_1BBB&PID_0052&MI_00
  AGPS  VID_1BBB&PID_0052&MI_01
  VOICE VID_1BBB&PID_0052&MI_02
  AT    VID_1BBB&PID_0052&MI_03
  Modem VID_1BBB&PID_0052&MI_05
  wwan  VID_1BBB&PID_0052&MI_06

  Diag  VID_1BBB&PID_00B6&MI_00
  AT    VID_1BBB&PID_00B6&MI_01
  Modem VID_1BBB&PID_00B6&MI_02
  wwan  VID_1BBB&PID_00B6&MI_03

  Diag  VID_1BBB&PID_00B7&MI_00
  AGPS  VID_1BBB&PID_00B7&MI_01
  VOICE VID_1BBB&PID_00B7&MI_02
  AT    VID_1BBB&PID_00B7&MI_03
  Modem VID_1BBB&PID_00B7&MI_04
  wwan  VID_1BBB&PID_00B7&MI_05

Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on

  wwan VID_1BBB&PID_0000&MI_04
  wwan VID_1BBB&PID_0017&MI_06

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver description files gives these names to the vendor specific
functions on this modem:

 Diagnostics VID_2357&PID_0201&MI_00
 NMEA        VID_2357&PID_0201&MI_01
 Modem       VID_2357&PID_0201&MI_03
 Networkcard VID_2357&PID_0201&MI_04
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver description files gives these names to the vendor specific
functions on this modem:

 Diag   VID_19D2&PID_0265&MI_00
 NMEA   VID_19D2&PID_0265&MI_01
 AT cmd VID_19D2&PID_0265&MI_02
 Modem  VID_19D2&PID_0265&MI_03
 Net    VID_19D2&PID_0265&MI_04
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Hyundai Petatel Inc. Nexpring NP10T terminal (EV-DO rev.A USB modem) ID
Signed-off-by: NDenis Kaganovich <mahatma@eu.by>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

also known as Alcatel One Touch L100V LTE

The driver description files gives these names to the vendor specific
functions on this modem:

 Application1: VID_1BBB&PID_011E&MI_00
 Application2: VID_1BBB&PID_011E&MI_01
 Modem:        VID_1BBB&PID_011E&MI_03
 Ethernet:     VID_1BBB&PID_011E&MI_04
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver description files gives these names to the vendor specific
functions on this modem:

 diag: VID_19D2&PID_0284&MI_00
 nmea: VID_19D2&PID_0284&MI_01
 at:   VID_19D2&PID_0284&MI_02
 mdm:  VID_19D2&PID_0284&MI_03
 net:  VID_19D2&PID_0284&MI_04
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: NQuentin.Li <snowmanli88@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Huawei E173 will normally appear as 12d1:1436 in Linux.  But
the modem has another mode with different device ID and a slightly
different set of descriptors. This is the mode used by Windows like
this:

  3Modem:      USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
  Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
  Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
  PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003

All interfaces have the same ff/ff/ff class codes in this mode.
Blacklisting the network interface to allow it to be picked up by
the network driver.

Cc: stable <stable@vger.kernel.org>
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NRui li <li.rui27@zte.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>