Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Patch 4 implements error handlers for pcie_portdrv.
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Patch 3 implements the core part of PCI-Express AER and aerdrv
port service driver.

When a root port service device is probed, the aerdrv will call
request_irq to register irq handler for AER error interrupt.

When a device sends an PCI-Express error message to the root port,
the root port will trigger an interrupt, by either MSI or IO-APIC,
then kernel would run the irq handler. The handler collects root
error status register and schedules a work. The work will call
the core part to process the error based on its type
(Correctable/non-fatal/fatal).

As for Correctable errors, the patch chooses to just clear the correctable
error status register of the device.

As for the non-fatal error, the patch follows generic PCI error handler
rules to call the error callback functions of the endpoint's driver. If
the device is a bridge, the patch chooses to broadcast the error to
downstream devices.

As for the fatal error, the patch resets the pci-express link and
follows generic PCI error handler rules to call the error callback
functions of the endpoint's driver. If the device is a bridge, the patch
chooses to broadcast the error to downstream devices.
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Patch 2 exports pcie_port_bus_type.
Signed-off-by: NZhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Have pcie_port_bus_register() notice and return errors.
Mark it __must_check so that its caller(s) must check its return value.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce msi_ht_cap_enabled() to check the MSI capability in the
Hypertransport configuration space.
It is used in a generic quirk quirk_msi_ht_cap() to check whether
MSI is enabled on hypertransport chipset, and a nVidia specific quirk
quirk_nvidia_ck804_msi_ht_cap() where two 2 HT MSI mappings have to
be checked.
Both quirks set the PCI_BUS_FLAGS_NO_MSI bus flag when MSI is disabled.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

0x08 is the HT capability, while PCI_CAP_ID_HT_IRQCONF would be
the subtype 0x80 that mpic_scan_ht_pic() uses.
Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HT.

And by the way, use it in the ipath driver instead of defining its
own HT_CAPABILITY_ID.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Export the PCI_BUS_FLAGS_NO_MSI flag of a PCI bus in the sysfs files
of its parent device and make it writable. Could be used to:
* disable MSI on a device which has not been blacklisted yet
* allow MSI when some setpci hacks enable MSI support (for instance
  on the ServerWorks HT2000 chipset where the MSI HT cap is disabled
  by default).
Architecture where some bus have no parent chipset cannot use this
strategy to change MSI support.

If the chipset does not have a subordinate bus, its 'bus_msi' file
is empty.

Also document and warn about the possible danger of changing the flag.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

pci_enable_msi() and pci_enable_msix() use the same code to detect
whether MSI might be enabled on this device. Factorize this code in
pci_msi_supported(). And improve the documentation about the fact
that only the root chipset must support MSI, but it is hard to
find the root bus so we check all parent busses MSI flags.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move MSI quirks in CONFIG_PCI_MSI, document why the serverworks quirk
does not simply set PCI_BUS_FLAGS_NO_MSI, and create a generic quirk
for other chipsets where setting PCI_BUS_FLAGS_NO_MSI is fine.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Hack uart_suspend_port() and uart_resume_port() so that serial console
ports are not suspended if CONFIG_DISABLE_CONSOLE_SUSPEND is set.

This makes it possible to debug the suspend and resume routines of all
device drivers as well as the lowest-level swsusp code with the help of the
serial console.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove the atomic counter for slab_reclaim_pages and replace the counter
and NR_SLAB with two ZVC counter that account for unreclaimable and
reclaimable slab pages: NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE.

Change the check in vmscan.c to refer to to NR_SLAB_RECLAIMABLE.  The
intend seems to be to check for slab pages that could be freed.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not display HIGHMEM memory sizes if CONFIG_HIGHMEM is not set.

Make HIGHMEM dependent texts and make display of highmem counters optional

Some texts are depending on CONFIG_HIGHMEM.

Remove those strings and remove the display of highmem counter values if
CONFIG_HIGHMEM is not set.

[akpm@osdl.org: remove some ifdefs]
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some buggy systems can machine check when config space accesses
happen for some non existent devices.  i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.

This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.

Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: NAndi Kleen <ak@suse.de>

virtual addresses don't belong into kernel logs for non debugging

Cc: clemens@ladisch.de
Signed-off-by: NAndi Kleen <ak@suse.de>

This patch (as783) simplifies the driver core slightly by removing four
unnecessary _get and _put methods.

It is vital that when a driver is removed from its bus's klist of
registered drivers, or when a device is removed from a driver's klist
of bound devices, that the klist updates complete synchronously.
Otherwise the kernel might try binding an unregistered driver to a
newly-registered device, or adding a device to the klist for a new
driver before it has been removed from the old driver's klist.

Since the removals must be synchronous, they don't need to update any
reference counts.  Hence the _get and _put methods can be dispensed
with.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a potential deadlock in the driver core.  It boils down to
the fact that bus_remove_device() calls klist_remove() instead of
klist_del(), thereby waiting until the reference count of the
klist_node in the bus's klist of devices drops to 0.  The refcount
can't reach 0 so long as a modprobe process is trying to bind a new
driver to the device being removed, by calling __driver_attach().  The
problem is that __driver_attach() tries to acquire the device's
parent's semaphore, but the caller of bus_remove_device() is quite
likely to own that semaphore already.

It isn't sufficient just to replace klist_remove() with klist_del().
Doing so runs the risk that the device would remain on the bus's klist
of devices for some time, and so could be bound to another driver even
after it was unregistered.  What's needed is a new way to distinguish
whether or not a device is registered, based on a criterion other than
whether its klist_node is linked into the bus's klist of devices.  That
way driver binding can fail when the device is unregistered, even if
it is still linked into the klist.

This patch (as782) implements the solution, by adding a new bitflag to
indiate when a struct device is registered, by testing the flag before
allowing a driver to bind a device, and by changing the definition of
the device_is_registered() inline.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This provides a build and run-time option to turn on multhreaded probe
for all PCI drivers.  It can cause bad problems on multi-processor
machines that take a while to find their root disks, and play havoc on
machines that don't use persistant device names for block or network
devices.

But it can cause speedups on some machines, my tiny laptop's boot goes
up by 0.4 seconds, and my desktop boots up several seconds faster.

Use at your own risk!!!
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the infrastructure for drivers to do a threaded probe, and
waits at init time for all currently outstanding probes to complete.

A new kernel thread will be created when the probe() function for the
driver is called, if the multithread_probe bit is set in the driver
saying it can support this kind of operation.

I have tested this with USB and PCI, and it works, and shaves off a lot
of time in the boot process, but there are issues with finding root boot
disks, and some USB drivers assume that this can never happen, so it is
currently not enabled for any bus type.  Individual drivers can enable
this right now if they wish, and bus authors can selectivly turn it on
as well, once they determine that their subsystem will work properly
with it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add lots of return-value checking.

<pcornelia.huck@de.ibm.com>: fix bus_rescan_devices()]
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The platform_notify call for Arm and PPC architectures needs to be called
before the driver attaches to the device.  The problem only presents itself
when hotplugging certain devices while the driver is already loaded.
Signed-off-by: NBrian Walsh <brian@walsh.ws>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When CONFIG_HOTPLUG is n, add_bind_files() definition is wrong.
This patch has fixed it.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Driver core: fix comments in drivers/base/power/resume.c
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sysfs_remove_bin_file() void.  If it detects an error,
printk the file name and call dump_stack().

sysfs_hash_and_remove() now returns an error code indicating
its success or failure so that sysfs_remove_bin_file() can
know success/failure.

Convert the only driver that checked the return value of
sysfs_remove_bin_file().
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Makes it easier for devices to create and remove binary attribute files
so they don't have to call directly into sysfs.  This is needed to help
with the conversion from struct class_device to struct device.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When moving class_device usage over to device, we need to handle
class_interfaces properly with devices.  This patch adds that support.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This change creates a devices/virtual/CLASS_NAME tree for struct devices
that belong to a class, yet do not have a "real" struct device for a
parent.  It automatically creates the directories on the fly as needed.


Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The network layer needs this to convert to using struct device instead
of a struct class_device.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds two new callbacks to the class structure:
	int	(*dev_uevent)(struct device *dev, char **envp, int num_envp,
			char *buffer, int buffer_size);
	void	(*dev_release)(struct device *dev);

And one pointer:
	struct device_attribute		* dev_attrs;

which all corrispond with the same thing as the "normal" class devices
do, yet this is for when a struct device is bound to a class.

Someday soon, struct class_device will go away, and then the other
fields in this structure can be removed too.  But this is necessary in
order to get the transition to work properly.

Tested out on a network core patch that converted it to use struct
device instead of struct class_device.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes an oops when a device is attached to a class, yet has no
"parent" device.  An example of this would be the "lo" device in the
network core.

We should create a "virtual" subdirectory under /sys/devices/ for these,
but no one seems to agree on a proper name for it yet...

Oh, and update my copyright on the driver core.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed for the network class devices in order to be able to
convert over to use struct device.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Teach platform_bus about the new suspend_late/resume_early PM calls,
issued with IRQs off.  Do we really need sysdev and friends any more,
or can janitors start switching its users over to platform_device so
we can do a minor code-ectomy?
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds warning when someone tries them from atomic context.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the new suspend_prepare() phase.  It doesn't seem very usable,
has never been tested, doesn't address fault cleanup, and would need
a sibling resume_complete(); plus there are no real use cases.  It
could be restored later if those issues get resolved.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a new PM_SYSFS_DEPRECATED config option to control whether or
not the /sys/devices/.../power/state files are provided.  This will
make it easier to get rid of that mechanism when the time comes,
and to verify that userspace tools work right without it.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updates to match current code:

 - Make writes to the /sys/devices/.../power/state files fail cleanly
   if the device requires the irqs-off call variants.

 - Fix comments describing the /sys/devices/.../power/state file writes
   to match the code; the last several releases have invalidated the
   previous text.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is the first of this series that should actually change any
behavior ...  by issuing the new event, now tha the rest of the kernel is
prepared to receive it.

This converts the PM core to issue the new PRETHAW message, which the rest of
the kernel is now ready to receive.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>