The feature flags list for i40e and i40evf is beginning to become pretty
massive.  I plan to add another 4 or so features to these drivers and
duplicating the flags for each and every flags list is becoming a bit
repetitive.

The primary change here is that we now build our features list around
hw_encap_features.  After that we assign that to vlan_features,
hw_features, and finally map that onto features.  In addition we end up
throwing features onto hw_encap_features that end up having no effect such
as the Rx offloads and SCTP_CRC.  However that should have no impact and
makes things a bit easier for us as hw_encap_features is one of the less
updated features maps available.

For i40evf I went through and sanity checked a few features as well.
Specifically RXCSUM was being set as a read-only feature which didn't make
much sense.  I have updated things so we can clear the NETIF_F_RXCSUM flag
since that is really a software feature and not a hardware one anyway so
disabling it is just a matter of ignoring the result from the hardware.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The newly added x550em_a support causes a link failure on ARM because of
an overly long time passed into udelay():

ERROR: "__bad_udelay" [drivers/net/ethernet/intel/ixgbe/ixgbe.ko] undefined!

There are multiple variants of the ixgbe_acquire_swfw_sync_*() function,
and the other ones all use msleep(), so we can safely assume that all
callers are allowed to sleep, which makes msleep() a better replacement
than mdelay().
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 49425dfc ("ixgbe: Add support for x550em_a 10G MAC type")
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch moves API negotiation into mac_ops.  The general idea here is
that with HyperV on the way we need to make certain that anything that will
have different versions between HyperV and a standard VF needs to be
abstracted enough so that we can have a separate function between the two
so we can avoid changes in one breaking something in the other.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for partial GSO segmentation in the case of
tunnels.  Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header.  This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Also cleanup a case where we're bit shifting a value into place, and use
an unsigned constant. Make use of the unsigned postfix in places where
BIT() macro is not appropriate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make use of GENMASK instead of open coding the equivalent operation
incorrectly.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several areas of ixgbe were written before widespread usage of the
BIT(n) macro. With the impending release of GCC 6 and its associated new
warnings, some usages such as (1 << 31) have been noted within the ixgbe
driver source. Fix these wholesale and prevent future issues by simply
using BIT macro instead of hand coded bit shifts.

Also fix a few shifts that are shifting values into place by using the
'u' prefix to indicate unsigned. It doesn't strictly matter in these
cases because we're not shifting by too large a value, but these are all
unsigned values and should be indicated as such.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is possible on some systems that crosstalk could lead to link flap
on empty SFP+ cages.  A new NVM bit was defined to let SW know it
needs to implement the work around which consists of verifying that
there is a module in the cage before acting on the LSC.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Somehow the wrong fc_setup function was used for x550em_a, so
correct that. Also set setup_link to NULL as its value is
determined later, just like it is with X550EM_x.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement per-queue statistics for packets, bytes and busy poll
specific counters.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This brings the logic closer to how we handle the stats in ixgbe and it
sets us up for introducing per-queue stats.

Use IXGBEVF_STAT and IXGBEVF_NETDEV_STAT for accessing the driver and
netdev stats respectively. This way we don't have to calculate the
stats based on register values which could lead to the counters not
being initialized properly when the interface is down.

IXGBEVF_QUEUE_STATS_LEN is set to include the number of queues.

Also some defines were renamed to use the IXGBEVF prefix.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use a new register to wait for previous register writes to complete
before issuing a register read. This is needed when slower links
are in use.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This field is used to record the RX queue index for a redirect action
passed via ring_cookie field in struct ethtool_rx_flow_spec which is
a u64 value.

For ex: after adding a filter rule to redirect to a VF using ethtool
  # echo 4 > /sys/class/net/p4p1/device/sriov_numvfs
  # ethtool -N p4p1 flow-type ip4 src-ip 192.168.0.1 action 0x100000000

querying for the rule shows the Action as 'Direct to queue 0'

  # ethtool -n p4p1
  4 RX rings available
  Total 1 rules

  Filter: 2045
 	Rule Type: Raw IPv4
	Src IP addr: 192.168.0.1 mask: 0.0.0.0
	Dest IP addr: 0.0.0.0 mask: 255.255.255.255
	TOS: 0x0 mask: 0xff
	Protocol: 0 mask: 0xff
	L4 bytes: 0x0 mask: 0xffffffff
	VLAN EtherType: 0x0 mask: 0xffff
	VLAN: 0x0 mask: 0xffff
	User-defined: 0x0 mask: 0xffffffffffffffff
	Action: Direct to queue 0

With this fix, ethtool will report the right queue index even for VFs.
	Action: Direct to queue 4294967296

Here 4294967296 corresponds to 0x100000000.
We need to update 'ethtool' to report the queue index as a Hex value so
that it is more  user friendly and matches with the 'action' value that
is passed when adding the rule.
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X550EM_a/x did not have a default value for mac->ops.setup_link which
was causing link issues for backplane devices.

This patch sets mac->ops.setup_link to ixgbe_setup_mac_link_X540 for
X550EM_a/x which is also default for X550. This will result in
mac->ops.setup_link calling the link setup function for the respective
PHY type in case we do not need a special function to deal with it.
Reported-by: NKen Cox <jkc@redhat.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously the PF driver would only set VLAN spoof checking if
the VF had created VLANs. This was done by setting and checking
a counter (vlan_count) whenever a VLAN was created by the VF.
However it is possible for the vlan_count to be !=0 while there are
no VLANs assigned to the VF due to the count incrementing every
time a VLAN 0 is added on ifdown/up, which resulted in VLAN spoofing
always being set for those VFs.

This patch cleans up the logic by unconditionally setting VLAN based on
how the VF is configured (via ip link set ethX vf Y spoofchk on/off).
This change also resolves an issue where the VLAN spoofing can remain
set even after being disabled by the user due to the driver enabling
VLAN spoof checking every time a VLAN is added to the VF, but would
only allow changes in the setting if vlan_count != 0.

Also default_vf_vlan_id and vlans_enabled were removed from the
vf_data_storage structure since they are not being used in the driver.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Consolidate the logic behind configuring spoof checking:

Move the setting of the MAC, VLAN and Ethertype spoof checking into
ixgbe_ndo_set_vf_spoofchk().

Change ixgbe_set_mac_anti_spoofing() to set MAC spoofing per VF similar
to the VLAN and Ethertype functions - this allows us to call the helper
functions in ixgbe_ndo_set_vf_spoofchk() for all spoof check types and
only disable MAC spoof checking when creating MACVLAN.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

vxlan_get_rx_port requires rtnl_lock to be held.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fm10k_open requires rtnl_lock to be held.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for and handle IPv6 extended headers so that Tx checksum offload
can be done. Also use skb_checksum_help for unexpected cases. This was
originally discovered in ixgbe.
Reported-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update every header file and other locations to consistently use
Intel(R) instead of just Intel. Also update copyright year of files
which we modified.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When writing a new default redirection table, we needed to populate
a new RSS table using ethtool_rxfh_indir_default. We populated this
table into a region of memory allocated using kcalloc, but never checked
this for NULL. Fix this by moving the default table generation into
fm10k_write_reta. If this function is passed a table, use it. Otherwise,
generate the default table using ethtool_rxfh_indir_default, 4 at at
time.

Fixes: 0ea7fae4 ("fm10k: use ethtool_rxfh_indir_default for default redirection table")
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Deleting lport when multicast mode is configured to
FM10K_XCAST_MODE_ALLMULTI or FM10K_XCAST_MODE_PROMISC will result in
generating orphaned multicast-group entries in the switch manager.
Before deleting the lport, reset multicast mode to FM10K_XCAST_MODE_NONE
to flush out these multicast-group entries.
Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The original comment may be read incorrectly as referring to checking
the *entire* length is zero. However, it merely checks only the reserved
bits of both length and reserved in a small amount of code. Update the
comment to indicate this is a clever trick and clearly spell out that it
only checks the reserve bits.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use a new #define FM10K_VLAN_OVERRIDE even though we're using the exact
same bit. The reason for this is clarity in the code, otherwise you can
read FM10K_VLAN_CLEAR and think it should be removed. Also add a comment
explaining why the FM10K_VLAN_OVERRIDE bit is set.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The diagram represents bit layout of the multi-bit VLAN update message
format. Typically these diagrams are drawn using some power of 2 as the
base, to more easily grasp where fields split. Although the numbers
above can make it somewhat easy to understand which bit you're looking
at, it makes the break points not line up. Re-draw the numbers using
base 8, and mark the bit values every 8 bits at the top. This should
make it more easy to grasp the table quickly.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

fm10k_tlv_parse_attr is supposed to return FM10K_NOT_IMPLEMENTED for any
TLV who's attribute id lies outside the range of results. It does not do
this today. In addition, the documentation does not indicate that other
attributes which are not implemented for a given TLV will be silently
ignored. Fix this. Clean up the logic so that we don't rely on the fact
that FM10K_NOT_IMPLEMENTED is greater than zero, as this can easily
cause confusion.

A future extension could look into some way of reporting unknown TLVs
in order to make issues more easily discoverable. We can't just return
FM10K_NOT_IMPLEMENTED here because we don't want to drop the entire
message if it has an unknown TLV.

While here, update the copyright year.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

fm10k_io_error_detected() does not need to call pci_disable_device(). In
the cases where the reset needs to occur, the stack flow will result in
calling fm10k_remove() which already disables the PCI device. If we
leave the pci_disable_device(), we result in a warning about disabling
an already disabled device.

Many PCI drivers do call pci_disable_device() in their .error_detected()
routines, but it does not appear to be required. In addition, these
drivers have a check "is_pci_enabled()" call in their remove routines,
which is how they chose to handle the duplicate device disable.

This seems incorrect, since the PCI device structure is reference
counted. It is very possible that the reference count for the PCI device
could be greater than 1. In this case, you would remove the PCI device
within the error_detected routine, reducing count to 1, then remove it
again in the remove function, reducing it to zero. This would result in
yet another disable somewhere else failing. Thus, we shouldn't be using
is_pci_enabled() to check for this issue. Instead, just remove the
extraneous pci_device_disable() found within the error_detected routine.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, any error responses from the switch manager after an
LPORT_MAP request are silently ignored. At most the mailbox message will
be reported as an error. This can result in unexpected behavior when the
switch manager has configured a port with zero bandwidth. Add support
for reading the fm10k_swapi_error structure from LPORT_MAP responses.

If the message contains the necessary TLV and has a non-zero error code,
report link down, clear the dglort_map, and delay the next
get_host_state call by a reasonable delay. Also log an error message
indicating that the LPORT_MAP request failed.

The delay ensures preventing an interrupt storm on the switch manager,
and reduces the number of mailbox messages we send in this scenario
drastically.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Multicast mode checking is no longer a requirement to perform unicast
and multicast address syncs. Specifically, a device operating in
promiscuous and/or all multicast mode is not excluded. The issue occurs
when the netdev is pre-configured to either multicast mode and is
enabled for the first time. The multicast-group table in the Switch
Manager will be missing obvious multicast entries associated to this
netdev.

Changes were also made to disallow unicast and multicast syncs with
VLAN 0. The Switch Manager considers VLAN 0 to be an invalid entry.
Requests with VLAN 0 by the netdev are only generated when the driver is
freshly installed and the default VID is not set.
Signed-off-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 1588 support within fm10k does not work correctly with the current
version of the switch management software, and likely never worked
correctly to begin with. Remove support for PTP/1588. Update copyright
year for all these files while we're touching them.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During an AER action response, we were calling fm10k_close without
holding the rtnl_lock() which could lead to possible RCU warnings being
produced due to 64bit stat updates among other causes. Similarly, we
need rtnl_lock() around fm10k_open during fm10k_io_resume. Follow the
same pattern elsewhere in the driver and protect the entire open/close
sequence.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use DRV_SUMMARY, similar to DRV_VERSION so that we don't have to
duplicate the driver summary in multiple places.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables bulk free in Tx cleanup for fm10k and cleans up the
boolean logic in the polling routines for fm10k in the hopes of avoiding
any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes an (ab)use of the ethtool stats API, which could
result in corrupt memory or misleading stat output. The ethtool stats
API is not robust enough to handle varying number of statistics due to
how it requests the size and allocates memory. Remove the poorly conceived
support originally added for extra debug statistics. In the future,
a new stats API may open up the ability to display these statistics.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refector broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set.

We can't simply remove the check of the upper 16 bits and the call to
fm10k_iov_select vid, because this would remove the checks for default
VID and for ensuring no other VLANs can be enabled except pf_vid when it
has been set. To resolve that issue, this revision uses the
iov_select_vid when we have a single-bit update, and denies any
multi-bit update when the VLAN was administratively set by the PF. This
should be ok since the PF properly updates VLAN_TABLE when it assigns
the PF vid. This ensures that requests to add or remove the PF vid work
as expected, but a rogue VF could not use the multi-bit update as
a loophole to attempt receiving traffic on other VLANs.
Reported-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet.  Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)."  It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.

I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.

Fixes: 2d37490b ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update ixgbe version number.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for x550em_a-based KR backplane devices.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for an SGMII backplane interface.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>