ret = hid_output_raw_report(A, B, C, HID_FEATURE_REPORT);
is equivalent to
  ret = hid_hw_raw_request(A, B[0], B, C, HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
whatever the transport layer is.

So use the new API where available
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid-input do not use anymore hid_output_raw_report() to set the LEDs.
Use the correct implementation now and make them working again.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

If there is no urbout when sending a output report, ENOSYS (Function
not implemented) is a better error than EIO (I/O error).
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Having our own .request() implementation does not give anything,
so use the generic binding.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add output_report and raw_request to i2c-hid.
The current implementation of i2c_hid_output_raw_report decides
by itself if it should use a direct send of the output report
or use the data register (SET_REPORT). Split that by reimplement
the logic in __i2c_hid_output_raw_report() which will be dropped
soon.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

.request() can be emulated through .raw_request()
we can implement this emulation in hid-core, and make .request
not mandatory for transport layer drivers.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

uHID is missing a SET_REPORT protocol implementation, but as
.hid_get_raw_report() as been removed from struct hid_device,
there were no means to access GET_REPORT in uhid.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This reverts commit 4a76d370. Removing
it was a mistake, as we need a means to access GET_REPORT.
Reported-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

uhid_hid_output_report() can be implemented through a simple call
to uhid_hid_output_raw().
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This function is now unused since cafebc05 ("HID: remove
hid_get_raw_report in struct hid_device").
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add a helper to access hdev->hid_output_raw_report().

To convert the drivers, use the following snippets:

for i in drivers/hid/*.c
do
  sed -i.bak "s/[^ \t]*->hid_output_raw_report(/hid_output_raw_report(/g" $i
done

Then manually fix for checkpatch.pl
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

dev->hid_get_raw_report(X) and hid_hw_raw_request(X, HID_REQ_GET_REPORT)
are strictly equivalent. Switch the hid subsystem to the hid_hw notation
and remove the field .hid_get_raw_report in struct hid_device.
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Well, no use to keep twice the same code.
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

All the different transport drivers use now the generic event handling
in hid-input. We can remove the handler definitively now.
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid-logitech-dj uses its own ->hidinput_input_event() instead of
the generic binding in hid-input.
Moving the handling of LEDs towards logi_dj_output_hidraw_report()
allows two things:
- remove hidinput_input_event in struct hid_device
- hidraw user space programs can also set the LEDs
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add the uhid_output_report transport-driver function to the uhid driver.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Acked-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add raw_request, set_raw_report and output_report transport-driver functions to
the USB HID driver.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Acked-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Use the naming scheme 'devicename:colour' for the Dualshock 4
LED lightbar controls as specified in Documentation/leds/leds-class.txt
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add annotated HID descriptor for the Dualshock 4.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Retrieve and cache the output report for the Dualshock 4 in sony_probe()
instead of repeatedly walking the report list in the worker function.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Use a modified HID descriptor for the Dualshock 4 to assign the gyroscope
sensors and accelerometers to axes.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix cosmetic spacing in the device definitions.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Use regular HID output reports instead of raw reports in the
dualshock4_state_worker function.  (Thanks Simon Mungewell)
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Use separate identifiers for Dualshock 4 controllers connected via USB and
Bluetooth.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Added support of RITMIX ROM-316 mouse to hid-holtek-mouse workaround module
Signed-off-by: NAlexey Kharlamov <derlafff@ya.ru>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This addresses regression caused by commit id "751d17e2"
 iio: hid-sensors: Fix power and report state.
This commit removed a quirk, to change the enumeration base
to 1 from 0 based on an CONFIG paramter. There was objection to
add more changes under this quirk, instead suggested to add an
HID quirk. But there is no easy way to add HID qurik as the
reports are not properly using collection class.

The solution was to use logical minimum, which is a correct way.
There were changes done in firmware to address this.

Unfortunately some devices, still use old FW and can't be upgraded
to newer version on Linux devices as there is no FW upgrade tool
available for Linux devices. So we need to fix report descriptors,
for such devices. This will not have any impact, if the FW uses
logical 1 as minimum.

In this patch we look for usage id for "power and report state", and
modify logical minimum value to 1.

Background on enum:
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This fix (not very clean though) should fix the long time USB3
issue that was spotted last year. The rational has been given by
Hans de Goede:

 ----

I think the most likely cause for this is a firmware bug
in the unifying receiver, likely a race condition.

The most prominent difference between having a USB-2 device
plugged into an EHCI (so USB-2 only) port versus an XHCI
port will be inter packet timing. Specifically if you
send packets (ie hid reports) one at a time, then with
the EHCI controller their will be a significant pause
between them, where with XHCI they will be very close
together in time.

The reason for this is the difference in EHCI / XHCI
controller OS <-> driver interfaces.

For non periodic endpoints (control, bulk) the EHCI uses a
circular linked-list of commands in dma-memory, which it
follows to execute commands, if the list is empty, it
will go into an idle state and re-check periodically.

The XHCI uses a ring of commands per endpoint, and if the OS
places anything new on the ring it will do an ioport write,
waking up the XHCI making it send the new packet immediately.

For periodic transfers (isoc, interrupt) the delay between
packets when sending one at a time (rather then queuing them
up) will be even larger, because they need to be inserted into
the EHCI schedule 2 ms in the future so the OS driver can be
sure that the EHCI driver does not try to start executing the
time slot in question before the insertion has completed.

So a possible fix may be to insert a delay between packets
being send to the receiver.

 ----

I tested this on a buggy Haswell USB 3.0 motherboard, and I always
get the notification after adding the msleep.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Rename sony_state_worker to sixaxis_state_worker since the function is now
sixaxis specific.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add LED lightbar controls for the Dualshock 4.

The Dualshock 4 light bar has 3 separate RGB LEDs that can range in
brightness from 0 to 255 so a full byte is now needed to store each LED's
state

Changed the module to support an arbitrary number of LEDs instead of being
hardcoded to 4.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Adds the Dualshock 4 to the HID device list and enables force-feedback.

Adds a Dualshock 4 specific worker function since the Dualshock 4 needs a
different report than the Sixaxis.

The right motor in the Dualshock 4 is variable so the full rumble value
is now passed to the worker function and clamped there if necessary.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Reformat and reword some of the comments to make them more understandable.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Currently the return variable ret is always 0.  Set it to other values in
error cases, as used in the direct return.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

we used to set the parent of the input device as the parent of
the hid bus. This was introduced when we created hid as a real bus, and
to keep backward compatibility. Now, it's time to proper set the parent
so that sysfs has an idea of which input device is attached to
which hid device.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add labels for BTN_DPAD_UP, BTN_DPAD_DOWN, BTN_DPAD_LEFT, BTN_DPAD_RIGHT and
BTN_TOOL_QUADTAP.

[jkosina@suse.cz: make changelog more verbose]
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The entries are not needed, as hid-multitouch gets bound correctly
automatically by contact ID.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

For 0xff05 usage in MS ergonomy keyboard quirk, we are falling through
and returning 0 instread of properly (because we've performed new mapping)
returning 1. Fix that.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

[jkosina@suse.cz: refresh to apply after SIS quirk merging]
Signed-off-by: NEmanuel Krenz <emanuelkrenz@web.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix kernel warning and failure to register sensor hub devices with MFD.  Now
many devices has in-built sensor hubs. So by default this HID hub, is properly
parsed and register individual sensors as platform device using MFD framework.
But if a second sensor hub is attached via USB, which has same sensors, it will
result in kernel warning and failure to register MFD cell as the platform
device sysfs file name will be same as created by in-built sensor hubs. This
patch sets MFD cell id to PLATFORM_DEVID_AUTO. In this way there will never be
duplicate sysfs file names.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

hid-logitech-dj.c driver needs hidraw to work correctly. Without
hidraw, hid-logitech-dj.c fails during probe() and Logitech
Unifying devices HID reports aren't recognized.

The unifying receiver has 3 usb interfaces. When hid-logitech-dj driver is
loaded, interfaces 0 and 1 are discarded.

Interface 2 consists of a hid class interface with 3 collections, each of
which sports the 'vendor' usage, thus, there is no reason for hid_input to
claim any of them. On the other hand, hidraw has no issue in claiming the
collections, even if they are 'vendor'. As of today, hid-logitech-dj uses
hidraw api to send configuration/control reports to interface 2 of the
Unifying receiver.

Without the hid-logitech-dj driver, interfaces 0 and 1 are claimed by
hid-input, as they correspond to a keyboard and a mouse. But that is not
relevant to the discussion.

[jkosina@suse.cz: make the changelog more verbose, thanks to Nestor]
Signed-off-by: NOlivier Gay <ogay@logitech.com>
Signed-off-by: NNestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: NMathieu Meisser <mmeisser@logitech.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

I have two Logitech Dual Action gamepads, both have same Vendor/Device id pair.
Newest gamepad (A) can switch between old mode (HID) and XBox gamepad emulation
mode. Old gamepad (B) can only work in HID mode.  In HID mode gamepad A sends
many EPIPE errors during initialization and was disconnected immediately after
connect  to usb port. It works fine in Win and Mac. After adding NOGET quirk in
driver, it was working properly.  Gamepad B works fine before and after
changes. I tested both gamepads with 3.8.0 and 3.11.6 kernels  with modified
driver. Follow patch can apply for current git kernel version. I can send pcap
log from usb bus with both gamepads or any other additional information if it
is needed
Signed-off-by: NVitaly Katraew <zawullon@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>