IS_ERR_VALUE macro should be used only with unsigned long type.
Specifically it works incorrectly with longer types.

The patch follows conclusion from discussion on LKML [1][2].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581

[ralf@linux-mips.org: While it may not immediately be obvious, the type
of st_value in the end is an unsigned long equivalent so the invocation
of IS_ERR_VALUE() was valid but I'm applying the patch anyway for
clarity.]
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12553/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Propagate sNaN payload in quieting in the legacy-NaN mode as well.  If
clearing the quiet bit would produce infinity, then set the next lower
trailing significand field bit, matching the SB-1 and BMIPS5000 hardware
implementations.  Some other MIPS FPU hardware implementations do
produce the default qNaN bit pattern instead.

This reverts some changes made for semantics preservation with commit
dc3ddf42 [MIPS: math-emu: Update sNaN quieting handlers], consequently
bringing back most of the semantics from before commit fdffbafb [Lots of
FPU bug fixes from Kjeld Borch Egevang.], except from the qNaN produced
in the infinity case.  Previously the default qNaN bit pattern was
produced in that case.
Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11483/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Update the ELF personality macros used for individual ABIs to make
actions in the same order across all of them and match formatting too.
Signed-off-by: NMaciej W. Rozycki <macro@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 8cb48fe1 ("MIPS: Provide correct siginfo_t.si_stime"),
MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h
directly before defining MIPS' struct siginfo, in order to get the
necessary definitions needed for the siginfo struct without the generic
copy_siginfo() hitting compiler errors due to struct siginfo not yet
being defined.

Now that the generic copy_siginfo() is moved out to linux/signal.h we
can safely include asm-generic/siginfo.h before defining the MIPS
specific struct siginfo, which avoids the uapi/ include as well as
breakage due to generic copy_siginfo() being defined before struct
siginfo.
Reported-by: NChristopher Ferris <cferris@google.com>
Fixes: 8cb48fe1 ("MIPS: Provide correct siginfo_t.si_stime")
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Petr Malat <oss@malat.biz>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0-
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

octeon_smp_setup and octeon_prepare_cpus are just used during initialization
period, so mark them as __init. And, octeon_prepare_cpus is just used in smp.c,
so make it static as well.
Signed-off-by: NYang Shi <yang.shi@windriver.com>
Cc: david.daney@cavium.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12574/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Remove unneeded leds0 alias.
- Switch to bcm6345-l1-intc interrupt controller.
- Use interrupt-controller instead of periph_intc and cpu_intc.
- Add uart1 node.
- Single ohci and ehci nodes.
- Avoid using underscores in node names.
- Rename uart aliases to serial.
- Remove blank line in cpus node.

[ralf@linux-mips.org: fix references in bcm96368mvwg.dts so the file keeps
building.]
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Remove unneeded leds0 alias.
- Switch to bcm6345-l1-intc interrupt controller.
- Use interrupt-controller instead of periph_intc and cpu_intc.
- Add uart1, ehci and ohci nodes.
- Refactor syscon and syscon-reboot.
- Avoid using underscores in node names.
- Rename uart aliases to serial.
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13043/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This SoC is very similar to BCM63168 and Broadcom usually refers to them as
BCM63268.
Add BCM63268 and missing BCM63168 to device tree documentation.
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13042/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds a device tree example for SFR Neufbox4 (Sercomm version), which
also serves as a real example for brcm,bcm6358-leds.
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13041/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

BCM6358 has a shared TLB which conflicts with current SMP support, so it must
be disabled for now.
BCM6358 uses >= 0xfffe0000 addresses for internal registers, which need to be
remapped (by using a simplified version of BRCM63xx ioremap.h).
However, 0xfff80000 is a better address, since it also covers BCM3368, leaving
the possibility to add it in the future.
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: robh@kernel.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13040/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Just to ease debugging of multiplatform kernel, make sure we print
"Broadcom BMIPS5200" for the BMIPS5200 implementation instead of
Broadcom BMIPS5000.

Fixes: 68e6a783 ("MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13014/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

BMIPS_GENERIC being multiplatform and intended to support BMIPS3200,
BMIPS3300, BMIPS4350, BMIPS4380 and BMIPS5000-class processors, there is
not much more we can put in there since they do not share the same I and
D cache line sizes at all (doubled for every new generation
essentially), some processors have a S-cache, some don't, some have a
FPU, some don't.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13013/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

local_r4k___flush_cache_all() is missing a special check for BMIPS5000
processors, we need to blast the S-cache, just like other MTI processors
since we have an inclusive cache. We also need an additional __sync() to
make sure this is completed.

Fixes: d74b0172 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13012/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

BMIPS5000 and BMIPS5200 processor have no D cache aliases, and this is
properly handled by the per-CPU override added at the end of
r4k_cache_init(), the problem is that the output of probe_pcache()
disagrees with that, since this is too late:

Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

With the change moved earlier, we now have a consistent output with the
settings we are intending to have:

Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes

Fixes: d74b0172 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13011/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

BMIPS5000 and BMIPS52000 processors have their I-cache filling from the
D-cache. Since BMIPS_GENERIC does not provide (yet) a
cpu-feature-overrides.h file, this was not set anywhere, so make sure
the R4K cache detection takes care of that.

Fixes: d74b0172 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13010/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bmips_be_defconfig
since this is a necessary option to parse the built-in flash partition
table on BMIPS big-endian SoCs (Cable Modem and DSL).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12256/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bcm63xx_defconfig
since this is a necessary option to parse the built-in flash partition
table on BCM63xx SoCs.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: simon@fire.lp0.eu
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12255/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Add DMA device
- Add NAND device
- Add GPIO device
- Add LED device
- Update the defconfig and rename it to loongson1b_defconfig
- Fix ioremap size
- Other minor fixes
Signed-off-by: NKelvin Cheung <keguang.zhang@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: dmaengine@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/13033/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fixes wrong bcm7425 SATA AHCI hardware interrupt property value with
periph_intc and SATA PHY unit address, and removes needless
brcm,broken-{ncq,phy} properties what are not used anywhere.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13017/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add UART, I2C, SATA device tree nodes on Broadcom BCM7xxx MIPS-based
platforms.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13016/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In Kconfig "=n" is not correct syntax, "!" is the preferred way for
false-positive expression.
Signed-off-by: NYang Shi <yang.shi@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12572/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When debugging a relocated kernel, the addresses of the relocated
symbols and the offset applied is essential information. If the kernel
is compiled with debugging information, then print this information
during bootup using the same function as the panic notifier.

[ralf@linux-mips.org: Fixed spelling mistake pointed out by
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>.]
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12989/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds KASLR to the MIPS kernel.

Entropy is derived from the banner, which will change every build and
random_get_entropy() which should provide additional runtime entropy.
Additionally the bootloader may pass entropy via the /chosen/kaslr-seed
node in device tree.

The kernel is relocated by up to RANDOMIZE_BASE_MAX_OFFSET bytes from
its link address (PHYSICAL_START). Because relocation happens so early
in the kernel boot, the amount of physical memory has not yet been
determined. This means the only way to limit relocation within the
available memory is via Kconfig.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12990/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Early access to the kernel command line requires early access to the FDT
for platforms which pass the command line within the device tree. There
was no common way to retrieve the location of the FDT without incurring
side effects, such as plat_mem_setup which, on Malta at least,
initializes a bunch of other stuff.

This patch adds plat_get_ftd() for IMG platforms.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12988/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add option to KConfig to enable the kernel to relocate itself at
runtime.

Relocation is supported R2 and later of the MIPS architecture, 32bit
and 64bit. The platform is also required to provide support through
plat_get_fdt() added in a later patch.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12987/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The kernel reserves all memory before the _end symbol as bootmem,
however, once the kernel can be relocated elsewhere in memory this may
result in a large amount of wasted memory. The assumption is that the
memory between the link and relocated address of the kernel may be
released back to the available memory pool.

Memory statistics for a Malta with the kernel relocating by
16Mb, without the patch:
Memory: 105952K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 25120K reserved, 0K cma-reserved)
And with the patch:
Memory: 122336K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 8736K reserved, 0K cma-reserved)

The 16Mb offset is removed from the reserved region and added back to
the available region.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12986/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

If CONFIG_RELOCATABLE is enabled, call relocate_kernel.

This function will return the entry point of the relocated kernel if
copy/relocate is sucessful or the original entry point if not. The stack
pointer must then be pointed into the new image.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12984/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/kernel/relocate.c contains the functions necessary to relocate
the kernel elsewhere in memory

The kernel makes a copy of itself at the new address. It uses the
relocation table inserted by the relocs tool to fix symbol references
within the new image.

If copy/relocation is sucessful then the entry point of the new kernel
is returned, otherwise fall back to starting the kernel in place.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12985/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When CONFIG_RELOCATABLE is enabled (added in later patch) add
--emit-relocs to vmlinux LDFLAGS so that fully linked vmlinux contains
relocation information.

Run the previously added relocs tool to fill in the .data.relocs section
of vmlinux with a table of relocations. The relocs tool will also remove
(mark as 0 length) the relocation sections added to vmlinux.

When vmlinux is passed to the boot makefile for conversion into a boot
image the now empty relocation sections will be removed and the
populated relocation table will be included in the binary image.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12983/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When CONFIG_RELOCATABLE is enabled, add a new section in the memory map
to be filled with relocation data.

CONFIG_RELOCATION_TABLE_SIZE allows the amount of space reserved to be
adjusted if necessary.

The relocs tool will populate this reserved space with relocation
information. The space is reserved within the elf by filling it with
0's, and an invalid entry is left at the start of the space such that
kernel relocation will be aborted if the table is empty.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12982/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Build the relocs tool as part of the kbuild
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12980/
Patchwork: https://patchwork.linux-mips.org/patch/13242/
Patchwork: https://patchwork.linux-mips.org/patch/13233/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This tool is based on the x86/boot/tools/relocs tool.

It parses the relocations present in the vmlinux elf file, building a
table of relocations that will be necessary to run the kernel from an
address other than its link address. This table is inserted into the
vmlinux elf, in the .data.relocs section. The table is subsequently used
by the code in arch/mips/kernel/relocate.c (added later) to relocate the
kernel.

The tool, by default, also marks all relocation sections as 0 length.
This is due to objcopy currently being unable to handle copying the
relocations between 64 and 32 bit elf files as is done when building a
64 bit kernel.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12981/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Previously the seccomp would only support strict mode on O32 userland
programs when the kernel had support for both O32 and N32 ABIs. Remove
kludge and support both ABIs.

With this patch in place, the seccomp_bpf self test now passes
global.mode_strict_support with N32 userland.
Suggested-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12917/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Commit d218af78 ("MIPS: scall: Always run the seccomp syscall
filters") modified the syscall code to always call the seccomp filters,
but missed the case where a filter may redirect the syscall, as
revealed by the seccomp_bpf self test.

The syscall path now restores the syscall from the stack after the
filter rather than saving it locally. Syscall number checking and
syscall function table lookup is done after the filter may have run such
that redirected syscalls are also checked, and executed.

The regular path of syscall number checking and pointer lookup is also
made more consistent between ABIs with scall64-64.S being the reference.

With this patch in place, the seccomp_bpf self test now passes
TRACE_syscall.syscall_redirected and TRACE_syscall.syscall_dropped on
all MIPS ABIs.

Fixes: d218af78 ("MIPS: scall: Always run the seccomp syscall filters")
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Eric B Munson <emunson@akamai.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12916/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The seccomp_bpf self test revealed that a 64bit kernel delivered an
invalid SIG_SYS to a 32bit userspace, because it was falling into the
default of the switch statement. Add a case to handle delivering the
signal.

With this patch, the seccomp_bpf self test now passes the TRAP.handler
case with O32 and N32 userlands.
Signed-off-by: NMatt Redfearn <matt.redfearn@imgtec.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Amanieu d'Antras <amanieu@gmail.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12915/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch updates the compatible string in the easy50712.dts file to the new
"lantiq,danube-pinctrl".
Signed-off-by: NMartin Schiller <mschiller@tdt.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: robh+dt@kernel.org
Cc: pawel.moll@arm.com
Cc: mark.rutland@arm.com
Cc: ijc+devicetree@hellion.org.uk
Cc: galak@codeaurora.org
Cc: john@phrozen.org
Cc: hauke@hauke-m.de
Cc: jogo@openwrt.org
Cc: daniel.schwierzeck@gmail.com
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11589/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Option is long gone, see

  5d9efa7e ("ipv6: Remove privacy config option.")
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/12919/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The generic header file is equivalent to the MIPS one, so use the
generic one instead.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12261/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:

    CPU0                            CPU1

    write to page
    flush_dcache_page
    flush_icache_page
    set_pte_at
                                    map page
    update_mmu_cache

If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.

To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.

When forking a process:

[   15.271842] [<80417630>] __update_cache+0xcc/0x188
[   15.277274] [<80530394>] copy_page_range+0x56c/0x6ac
[   15.282861] [<8042936c>] copy_process.part.54+0xd40/0x17ac
[   15.289028] [<80429f80>] do_fork+0xe4/0x420
[   15.293747] [<80413808>] handle_sys+0x128/0x14c

When exec'ing an ELF binary:

[   14.445964] [<80417630>] __update_cache+0xcc/0x188
[   14.451369] [<80538d88>] move_page_tables+0x414/0x498
[   14.457075] [<8055d848>] setup_arg_pages+0x220/0x318
[   14.462685] [<805b0f38>] load_elf_binary+0x530/0x12a0
[   14.468374] [<8055ec3c>] search_binary_handler+0xbc/0x214
[   14.474444] [<8055f6c0>] do_execveat_common+0x43c/0x67c
[   14.480324] [<8055f938>] do_execve+0x38/0x44
[   14.485137] [<80413808>] handle_sys+0x128/0x14c

These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.

Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Reported-by: NIonela Voinescu <ionela.voinescu@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Fixes: 4d46a67a ("MIPS: Fix race condition in lazy cache flushing.")
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12722/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12721/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>