Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For uAPSD support we'll need to have per-AC PS
buffers. As this is a major undertaking, split
the buffers before really adding support for
uAPSD. This already makes some reference to the
uapsd_queues variable, but for now that will
never be non-zero.

Since book-keeping is complicated, also change
the logic for keeping a maximum of frames only
and allow 64 frames per AC (up from 128 for a
station).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 will expire normal PS-buffered frames, but
if the device rejected some frames for a sleeping
station, these won't be on the ps_tx_buf queue but
on the tx_filtered queue instead; this is done to
avoid reordering.

However, mac80211 will not expire frames from the
filtered queue, let's fix that.

Also add a more comments to what all this expiry is
doing and how it works.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the TIM bit for a given station is set
and cleared all over the place. Since the logic to
set/clear it will become much more complex when we
add uAPSD support, as a first step let's collect
the entire logic in one place. This requires a few
small adjustments to other places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.

For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.

ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.

Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.

During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.

When setup completes and the peer is authorized, send data directly,
bypassing the AP.

In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).

In addition, make sure all peers are removed on disassociation.

A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Register and implement the TDLS cfg80211 callback functions.

Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.

Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed a possible issue in the max_tp_rate2 management of
minstrel_ht. In particular, if we look up just among max_tp_rate2 of
each group it will be possible that the selected rate will not be the
mcs with second maximum throughput. I wrote this simple patch.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.

This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Send a Mesh Peering Close frame when we deactivate a mesh peer link.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an AP interface is removed without the
AP/VLAN interfaces having been removed before
already, the AP-VLAN interface might still
have sleeping stations and buffer multicast
frames which will happen on the AP interface.
Thus, we need to remove AP/VLAN interfaces
before purging buffered broadcast frames.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "mac80211: stop tx before doing hw config and
rate update" stops the tx queue and call drv_flush so frequently
whenever a beacon got received with 11n htcap. This leads to
massive "Failed to stop TX DMA" logspam on embedded hw. So the
queue stop and flush should be called if and only if there is a
change in the channel type.
Reported-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hw.conf.channel value is not updated properly for drivers that
support HW channel switch.  Since the switch is done entirely by the
driver and we don't call ieee80211_hw_config(), this value remains
untouched.  This patch fixes that by setting the new channel directly in
ieee80211_chswitch_work().
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the
presence of the mesh control header in their QoS header.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to support QoS in mesh, we need to assign queue mapping only
after the next hop has been resolved, both for forwarded and locally
originated frames.  Also, now that this is fixed, remove the XXX comment
in ieee80211_select_queue().

Also, V-Shy Ho reported that the queue mapping was not being applied to
the forwarded frame (fwd_skb instead of skb).  Fixed that as well.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Juuso optimised the timer to not run all the
time in commit 3393a608.
However, after that it will still run once
more even if all frames just expired. Fixing
that also makes the function return value a
little clearer in the process.

Also, while at it, change the return value
to bool (instead of int).

Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Minstrel HT tries very hard to establish a BA session with
each peer once there's some data on the way. However the
stack does not inform minstrel if an aggregation session
is already in place, so it keeps trying and wastes good
cycles in the tx status path.

[ 8149.946393] Open BA session requested for $AP tid 0
[ 8150.048765] Open BA session requested for $AP tid 0
[ 8150.174509] Open BA session requested for $AP tid 0
[ 8150.274376] Open BA session requested for $AP tid 0
...
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The assumption is that during the hw config, transmission was
already stopped by mac80211. Sometimes the AP can be switching
b/w the ht modes due to intolerant or etc where STA is in
the middle of transmission. In such scenario, buffer overflow
was observed at driver side. And also before updating the rate
control, the frames are continued to xmited with older rates.
This patch ensures that the frames are always xmitted with
updated rates and avoid buffer overflow.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx flow control for non-mesh modes of operation only needs to act on the
net device queues: when the hardware queues are full we stop accepting
traffic from the net device.  In mesh, however, we also need to stop
forwarding traffic.  This patch checks the hardware queues before
attempting to forward a mesh frame.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To check whether a frame is in the RMC, we need access to the mesh
header.  This header is encrypted in encrypted data frames, so make this
check after the frame has been decrypted.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To properly maintain the peer's block ack window, the driver needs to be
able to control the new starting sequence number that is sent along with
the BlockAckReq frame.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calls to kzalloc() weren't checked here and it upsets the static
checkers.  Obviously they're not super likely to fail, but we might
as well add some error handling.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this flag is set, Tx A-MPDU sessions will not be started by
mac80211. This flag is required for devices that support Tx A-MPDU setup
in hardware.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removing unnecessary messages saves code and text.

Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to take the mpath state lock when an mpath is removed.
Also, no need checking the lock when reading mpath flags.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>