Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove frame logic from start_pool cb using the new iface
for async send.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove frame logic from transceive cb using new iface
for async send.

For pn533_wq_mi_recv() use pn533_send_cmd_direct_async which
sends the cmd directly to the hardware, skipping cmd queue.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove frame logic from InJmumpForDEP command using
the new iface for async send.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove frame logic from TgSetData and TgGetData commands
using the new iface for async send.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The reference count bump on the llcp Rx path is leading to a memory leak
whenever we're not receiving an I frame.
We fix that by removing the refcount bump (drivers must not free their
received skb) and using it only in the I frame path, when the frame is
actually queued. In that case, the skb will only be freed when someone
fetches it from userspace. in all other cases, LLCP received frames will
be freed when leaving the Rx work queue.
Reported-by: NEric Lapuyade <eric.lapuyade@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Not only it was improperly use to queue backlogged RX skbuffs, but it was
also not processed at all.
If the socket receive queue is full we simply drop the incoming packets.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove obsolate pn533_send_cmd_frame_sync() and use
previously added new iface for sync send.

The new interface require the use of individual skb for each
cmd which removes some memcpy calls and hides frame logic.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Allocate sk_buff for the request.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

It is intended to replace pn533_send_cmd_frame_sync() iface which
requires from the caller to create complete frame.

The new function constructs a complete frame itself and sends it out
in sync manner. This way frame logic is hidden from the caller.

pn533_send_cmd_sync() returns ERR_PTR in case of an error or a pointer
to valid response sk_buff otherwise. The pointer must be freed by the
caller when it's been consumed.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This iface is intended to be used with DEP transfers. It differs
from pn533_send_cmd_async() in the way the response skb is allocated.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is intendend to replace pn533_send_cmd_frame_async() which
requires from the caller to create a complete frame.

The new function constructs a frame and sends it out which hides the
frame logic and avoid code duplication.

The caller has to allocate skb and put its payload there, and finally
provide the skb together with a complete cb to pn533_send_cmd_async().

Response skb is allocated by the core part and pass to the caller cb.
Next, the caller has to free it when is not needed anymore or pass it
up to the stack.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

__pn533_send_cmd_frame_async() is called when lock is held so GFP_KERNEL
flag will be always used. Thus, having extra param does not optimise the
code.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

PN533_CMD_DATAEXCH_HEAD_LEN includes a frame header length which is not
seen at a glance. It can be missleading, so split it and define the
frame header length explicitly.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

in_maxlen and out_maxlen was replaced with PN533_NORMAL_FRAME_MAX_LEN
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Set timestamp in sent and received sk_buffs. timestamp is then put in
msghdr structure in llcp_sock_recvmsg().
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch is an enhacement to mwifiex_pcie driver to use
map/unmap PCI memory APIs. This reduces one memcpy each in TX
path and RX path, and enhances throughput.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds handler to clean PCIe TX rings after disconnect
or bss stop is called for PCIe based mwifiex driver.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch uses pci_alloc_consistent and pci_free_consistent
APIs for mwifiex_pcie driver. Consistent DMA memory is allocated
for TX, RX and event rings. Command buffer and command response
buffer also uses map/unmap memory APIs to download commands and
get command responses.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for init_fw_port handler for PCIe
interface, which resets RXBD read pointer for PCIe.
This fixes issue where RX doesn't work until some TX from
driver happens.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug for few instances where PCIe interrupt
status variable is accessed without holding spin lock.
This can result into missing interrupts.

Fix this by copying interrupt status to a local variable and
then using it for calling specific routine.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new name better matches the use of this variable.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This member is not needed any more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some cores do not have a IRQ assigned and some do not support when an
IRQ is assigned to them, this is now handled and printed out in the
code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The assignment of the IRQs to the cores of the chips by iterating over
the cores is complicated and causes problems with SoC like the BCM4706
with two GMAC core where just one should get a dedicated IRQ number.
Now the code assigns the same IRQs to the cores as the code from the
Broadcom SDK does. If the SoC is not know the current assigned IRQs are
only read out and an error message is printed.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This bcma_find_core_unit() is needed by the mips driver in the next
patch.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

New firmware is required to support
a) Add support for additional ampdu streams
b) Handle corresponding watchdog events to destroy ampdu streams

Bumping firmware API version by one.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, command path waits till all the tx host queues
are empty. Whenever watchdog event is raised, firmware
expects driver to destroy ampdu queues immediately.

This requires corresponding commands i.e.
mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be
sent without waiting for the tx queues to be completely
empty.

Use "watchdog_event_pending" to ensure the above mentioned
two commands are sent down immediately.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With more ampdu streams, we need to handle watchdog
events for the new ampdu streams. Handle these
events appropriately.

Earlier mwl8k_cmd_get_watchdog_bitmap used to return
only one stream index and hence bitwise operations
on the return value were not required. Now the function
returns a bitmap with different bits are mapped with
different stream indices.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, mwl8k_ampdu_stream is passed as one of the
argument to the function mwl8k_destroy_ba. Instead of
this pass only the stream index. This will be helpful
during watchdog event handling when bitmap of stream
indices are received.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, we have 2 ampdu streams that can be created
simultaneously. Firmware is capable of supporting
additional streams. Add support to use these streams.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set ACK policy to NORMAL when its not going to
be an AMPDU packet.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ampdu stream index can be derived from stream->idx.
So we no longer need stream->txq_idx, hence removing it.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>