Instead of allocating space for the whole xhci_hcd structure at the end of
usb_hcd, make the USB core allocate enough space for a pointer to the
xhci_hcd structure.  This will make it easy to share the xhci_hcd
structure across the two roothubs (the USB 3.0 usb_hcd and the USB 2.0
usb_hcd).

Deallocate the xhci_hcd at PCI remove time, so the hcd_priv will be
deallocated after the usb_hcd is deallocated.  We do this by registering a
different PCI remove function that calls the usb_hcd_pci_remove()
function, and then frees the xhci_hcd.  usb_hcd_pci_remove() calls
kput() on the usb_hcd structure, which will deallocate the memory that
contains the hcd_priv pointer, but not the memory it points to.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Make sure to call into the USB core's link, unlink, and giveback URB
functions with the usb_hcd pointer found by using urb->dev->bus.  This
will avoid confusion later, when the xHCI driver will deal with URBs from
two separate buses (the USB 3.0 roothub and the faked USB 2.0 roothub).

Assume xhci_urb_dequeue() will be called with the proper usb_hcd.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Commit d199c96d by Alan Stern ensured that low speed and full speed
devices below a high speed hub without a transaction translator (TT) would
never get enumerated.  Simplify the check for a TT in the xHCI virtual
device allocation to only check if the usb_device references a parent's
TT.

Make sure not to set the TT information on LS/FS devices directly
connected to the roothub.  The xHCI host doesn't really have a TT, and the
host will throw an error when those virtual device TT fields are set for a
device connected to the roothub.  We need this check because the xHCI
driver will shortly register two roothubs: a USB 2.0 roothub and a USB 3.0
roothub.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Make the USB 3.0 roothub registered by the USB core have a SuperSpeed
Endpoint Companion Descriptor after the interrupt endpoint.  All USB 3.0
devices are required to have this, and the USB 3.0 bus specification
(section 10.13.1) says which values the descriptor should have.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

In USB 3.0, there are two types of resets: a "hot" port reset and a "warm"
port reset.  The hot port reset is always tried first, and involves
sending the reset signaling for a shorter amount of time.  But sometimes
devices don't respond to the hot reset, and a "Bigger Hammer" is needed.

External hubs and roothubs will automatically try a warm reset when the
hot reset fails, and they will set a status change bit to indicate when
there is a "BH reset" change.  Make sure the USB core clears that port
status change bit, or we'll get lots of status change notifications on the
interrupt endpoint of the USB 3.0 hub.

(Side note: you may be confused why the USB 3.0 spec calls the same type
of reset "warm reset" in some places and "BH reset" in other places.  "BH"
reset is supposed to stand for "Big Hammer" reset, but it also stands for
"Brad Hosler".  Brad died shortly after the USB 3.0 bus specification was
started, and they decided to name the reset after him.  The suggestion was
made shortly before the spec was finalized, so the wording is a bit
inconsistent.)
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Update the USB core to deal with USB 3.0 hubs.  These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size.  Change the USB core's hub descriptor to have a
union for the last fields that differ.  Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.

Translate the new version of the hub port status field into the old
version that khubd understands.  (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)

Add new code to handle link state change status.  Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.

This patch is a modified version of the original patch submitted by John
Youn.  It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>

The USB core will set hcd->state to HC_STATE_RUNNING before calling
xhci_run, so there's no point in setting it twice.  The USB core also
doesn't pay attention to HC_STATE_RUNNING on the resume path anymore; it
uses HCD_RH_RUNNING(), which looks at hcd->flags & (1U <<
HCD_FLAG_RH_RUNNING.  Therefore, it's safe to remove the state set in
xhci_bus_resume().
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

We would like to allow host controller drivers to stop using hcd->state.
Unfortunately, some host controller drivers use hcd->state as an
implicit way of telling the core that a controller has died.  The
roothub registration functions must assume the host died if hcd->state
equals HC_STATE_HALT.

To facilitate drivers that don't want to set hcd->state to
HC_STATE_RUNNING in their initialization routines, we set the state to
running before calling the host controller's start function.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The xHCI driver doesn't ever test hcd->state for HC_STATE_HALT.  The USB
core recently stopped using it internally, so there's no point in setting
it in the driver.  We still need to set HC_STATE_RUNNING in order to make
it past the USB core's hcd->state check in register_roothub().
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears
Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's
too short and often cause dmesg shows "Host controller not halted, aborting
reset." message when rmmod xhci-hcd.

Modify the time limit to comply with xHCI 1.0 specification and prevents the
warning message showing when remove xhci-hcd.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Set hcd->state = HC_STATE_SUSPENDED if there is a power loss during system
resume or the system is hibernated, otherwise leave it be. The variable
old_state is redundant and made an unreachable code path, so remove it.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The xhci_bus_suspend() and xhci_bus_resume() functions are a bit hard to
read, because they have an ambiguously named variable "port".  Rename it
to "port_index".  Introduce a new temporary variable, "max_ports" that
holds the maximum number of roothub ports the host controller supports.
This will reduce the number of register reads, and make it easy to change
the maximum number of ports when there are two roothubs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The USB core only allows up to 31 (USB_MAXCHILDREN) ports under a roothub.
The xHCI driver keeps track of which ports are suspended, which ports have
a suspend change bit set, and what time the port will be done resuming.
It keeps track of the first two by setting a bit in a u32 variable,
suspended_ports or port_c_suspend.  The xHCI driver currently assumes we
can have up to 256 ports under a roothub, so it allocates an array of 8
u32 variables for both suspended_ports and port_c_suspend.  It also
allocates a 256-element array to keep track of when the ports will be done
resuming.

Since we can only have 31 roothub ports, we only need to use one u32 for
each of the suspend state and change variables.  We simplify the bit math
that's trying to index into those arrays and set the correct bit, if we
assume wIndex never exceeds 30.  (wIndex is zero-based after it's
decremented from the value passed in from the USB core.)  Finally, we
change the resume_done array to only hold 31 elements.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>

The irq enabling code is going to be refactored into a new function, so
clean up some checkpatch errors before moving it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header.  include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor.  This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.

Remove the bitmap #define and replace instances of it in the host
controller code.  Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>

The test of placing a number of command no-ops on the command ring and
counting the number of no-op events that were generated was only used
during the initial xHCI driver bring up.  This test is no longer used, so
delete it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The PM core reacts badly when the return code from usb_runtime_suspend()
is not 0, -EAGAIN, or -EBUSY.  The PM core regards this as a fatal error,
and refuses to run anymore PM helper functions.  In particular,
usbfs_open() and other usbfs functions will fail because the PM core will
return an error code when usb_autoresume_device() is called.  This causes
libusb and/or lsusb to either hang or segfault.

If a USB device cannot suspend for some reason (e.g. a hub doesn't report
it has remote wakeup capabilities), we still want lsusb and other
userspace programs to work.  So return -EBUSY, which will fill people's
log files with failed tries, but will ensure userspace still works.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The Tegra2 USB controller doesn't properly deal with misaligned DMA
buffers, causing corruption.  This is especially prevalent with USB
network adapters, where skbuff alignment is often in the middle of a
4-byte dword.

To avoid this, allocate a temporary buffer for the DMA if the provided
buffer isn't sufficiently aligned.
Signed-off-by: NRobert Morell <rmorell@nvidia.com>
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.

The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add generic access ops for controllers with a ulpi viewport register
(e.g. Chipidea/ARC based controllers).
Signed-off-by: NBenoit Goby <benoit@android.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I picked up a new DAK-780EX(professional digitl reverb/mix system),
which use CH341T chipset to communication with computer on 3/2011
and the CH341T's vendor code is 1a86

Looking up the CH341T's vendor and product id's I see:

1a86  QinHeng Electronics
  5523  CH341 in serial mode, usb to serial port converter

CH341T,CH341 are the products of the same company, maybe
have some common hardware, and I test the ch341.c works
well with CH341T

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On a laptop I see these errors on (most) resumes:
    hub 3-0:1.0: over-current change on port 1
    hub 3-0:1.0: over-current change on port 2

Since over-current conditions can disappear quite quickly it's better to
downgrade that message to debug level, recheck for an over-current
condition a little later and only print and over-current condition error
if that condition (still) exists when it's rechecked.

Add similar logic to hub over-current changes. (That code is untested,
as those changes do not occur on this laptop.)
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the following section mismatch warning:

WARNING: drivers/usb/built-in.o(.data+0x74c): Section mismatch in reference from the variable ehci_atmel_driver to the function .init.text:ehci_atmel_drv_probe()
The variable ehci_atmel_driver references
the function __init ehci_atmel_drv_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adding support for the OLIMEX ARM-USB-OCD-H JTAG device (id 15ba:002b)
based on FTDI FT2232H
Signed-off-by: NJF Argentino <jf.argentino@free.fr>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On https://bugs.launchpad.net/ubuntu/+source/linux/+bug/636091, one of
the cases reported is a big timeout on option_send_setup, which causes
some side effects as tty_lock is held. Looks like some of ZTE MF626
devices also don't like the RTS/DTR setting in option_send_setup, like
with 4G XS Stick W14. The reporter confirms which this it solves the
long freezes in his system.
Signed-off-by: NHerton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Direct access to PMIC register is not safe and will impact battery
charging. New IPC command supported in SCU FW for VBus power control.
USB OTG driver will switch to such commands instead of direct access
to PMIC register for safety and SCU FW will handle the actual work
after got the request(IPC command).

Due to this change, usb driver should wait more time for sync OTGSC
with USBCFG by SCU. Update wait time from 2ms to 5ms.
Signed-off-by: NHao Wu <hao.wu@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
This patch changes these boards to use the common implementation for GPIO
controlled pullup in the UDC driver.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.

Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).

Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.

So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit ab1666c1 (USB: quirk PLL power down mode)
added code that reads the revision ID from the PCI configuration register while
it's stored by PCI subsystem in the 'revision' field of 'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a problem with my previous patch series where there's a great
risk that the kernel will crash when unplugging interrupt devices from
the USB port. These lines must have got missing when I rebased the
patches from the older kernel I was working with to 2.6.37 and 2.6-next:

This fixes a bug where the kernel may crash if you unplug a USB device
that has active interrupt transfers.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The hcd->state variable is a disaster.  It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes.  It's
not protected by any locks.  And there's no mechanism to prevent it
from going through an invalid transition.

This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died.  Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information.  The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).

The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them.  Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT.  Nevertheless, the new code is a
big improvement over the current code.

The patch makes one other change.  The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.

This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NAlex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

timeout variable is not used anywhere in int write_cmd_usb, remove it
Signed-off-by: NHuzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

is_iso variable is not used anywhere, remove it
Signed-off-by: NHuzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

trivial patch to remove unused delay_t varible
Signed-off-by: NHuzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Driver was taking max() of a size_t and u32 which causes complaint
about comparison of different types.

Stumbled on this accidently in my config, never used.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In wusb_cluster_id_get(), if no zero bits exist in wusb_cluster_id_table,
find_first_zero_bit() returns CLUSTER_IDS.

But it is impossible to detect that the bitmap is full because there
is an off-by-one error in the return value check.  It will cause
unexpected memory access by setting bit out of wusb_cluster_id_table
bitmap, and caller will get wrong cluster id.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The SH EHCI/OHCI driver hardcoded the CPU type in {ehci,ohci}-hcd.c.
So if we will add the new CPU, we had to add to the hcd driver each time.
The patch adds the CONFIG_USB_{EHCI,OHCI}_SH configuration. So if we
want to use the SH EHCI/OHCI, we only enable the configuration.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>