Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 15 1月, 2015 11 次提交
  3. 10 1月, 2015 1 次提交
  5. 09 1月, 2015 5 次提交
  7. 08 1月, 2015 4 次提交
    • A
      arm64/efi: add missing call to early_ioremap_reset() · 0e63ea48
      由 Ard Biesheuvel 提交于 
      The early ioremap support introduced by patch bf4b558e
("arm64: add early_ioremap support") failed to add a call to
early_ioremap_reset() at an appropriate time. Without this call,
invocations of early_ioremap etc. that are done too late will go
unnoticed and may cause corruption.

This is exactly what happened when the first user of this feature
was added in patch f84d0275 ("arm64: add EFI runtime services").
The early mapping of the EFI memory map is unmapped during an early
initcall, at which time the early ioremap support is long gone.

Fix by adding the missing call to early_ioremap_reset() to
setup_arch(), and move the offending early_memunmap() to right after
the point where the early mapping of the EFI memory map is last used.

Fixes: f84d0275 ("arm64: add EFI runtime services")
Cc: <stable@vger.kernel.org>
Signed-off-by: NLeif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
      0e63ea48
    • G
      ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region · ac084688
      由 Grygorii Strashko 提交于 
      Now local variables kernel_x_start and kernel_x_end defined using
'unsigned long' type which is wrong because they represent physical
memory range and will be calculated wrongly if LPAE is enabled.
As result, all following code in map_lowmem() will not work correctly.

For example, Keystone 2 boot is broken because
 kernel_x_start == 0x0000 0000
 kernel_x_end   == 0x0080 0000

instead of
 kernel_x_start == 0x0000 0008 0000 0000
 kernel_x_end   == 0x0000 0008 0080 0000
and as result whole low memory will be mapped with MT_MEMORY_RW
permissions by code (start > kernel_x_end):
		} else if (start >= kernel_x_end) {
			map.pfn = __phys_to_pfn(start);
			map.virtual = __phys_to_virt(start);
			map.length = end - start;
			map.type = MT_MEMORY_RW;

			create_mapping(&map);
		}

Hence, fix it by using phys_addr_t type for variables kernel_x_start
and kernel_x_end.
Tested-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      ac084688
    • M
      ARM: 8249/1: mm: dump: don't skip regions · cca547e9
      由 Mark Rutland 提交于 
      Currently the arm page table dumping code starts dumping page tables
from USER_PGTABLES_CEILING. This is unnecessary for skipping any entries
related to userspace as the swapper_pg_dir does not contain such
entries, and results in a couple of unfortuante side effects.

Firstly, any kernel mappings which might exist below
USER_PGTABLES_CEILING will not be accounted in the dump output. This
masks any entries erroneously created below this address.

Secondly, if the final page table entry walked is part of a valid
mapping the page table dumping code will not log the region this entry
is part of, as the final note_page call in walk_pgd will trigger an
early return when 0 < USER_PGTABLES_CEILING. Luckily this isn't seen on
contemporary systems as they typically don't have enough RAM to extend
the linear mapping right to the end of the address space.

Due to the way addr is constructed in the walk_* functions, it can never
be less than USER_PGTABLES_CEILING when walking the page tables, so it
is not necessary to avoid dereferencing invalid table addresses. The
existing checks for st->current_prot and st->marker[1].start_address are
sufficient to ensure we will not print and/or dereference garbage when
trying to log information.

This patch removes both problematic uses of USER_PGTABLES_CEILING from
the arm page table dumping code, preventing both of these issues. We
will now report any low mappings, and the final note_page call will not
return early, ensuring all regions are logged.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      cca547e9
    • R
      ARM: wire up execveat syscall · 841ee230
      由 Russell King 提交于 
      Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      841ee230
  9. 07 1月, 2015 7 次提交
  11. 06 1月, 2015 2 次提交
  13. 05 1月, 2015 3 次提交
  15. 04 1月, 2015 2 次提交
  17. 31 12月, 2014 2 次提交
  19. 30 12月, 2014 1 次提交
    • S
      Add USB_EHCI_EXYNOS to multi_v7_defconfig · 007487f1
      由 Steev Klimaszewski 提交于 
      Currently we enable Exynos devices in the multi v7 defconfig, however, when
testing on my ODROID-U3, I noticed that USB was not working.  Enabling this
option causes USB to work, which enables networking support as well since the
ODROID-U3 has networking on the USB bus.

[arnd] Support for odroid-u3 was added in 3.10, so it would be nice to
backport this fix at least that far.
Signed-off-by: NSteev Klimaszewski <steev@gentoo.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      007487f1
  21. 29 12月, 2014 2 次提交