This patch adds KEYBOARD_ST_KEYSCAN config
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This patch enables SDHCI STI platform driver.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NAjit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

When CPU topology is specified in device tree, cpu_logical_map() does
not return core ID anymore, but rather full MPIDR value. This breaks
existing calculation of PMU register offsets on Exynos SoCs.

This patch fixes the problem by adjusting the code to use only core ID
bits of the value returned by cpu_logical_map() to allow CPU topology to
be specified in device tree on Exynos SoCs.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The pwm driver requires a clocks property referencing the pwm peripheral
clk.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

udphs_clk (USB Device Controller clock) is referenced instead of
uhphs_clk (USB Host Controller clock).
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Correct the typo error for the second "uhphs_clk".
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The i.MX6 reference manual doesn't make a clear distinction
between the fixed clock divider and the enable gate for the
pcie and sata reference clocks. This lead to the lvds mux
inputs in the imx6q clk driver to be parented from the
ref clock (which is the divider) instead of the actual gate,
which in turn prevents the upstream clock to actually be
enabled when lvds clk out is active.

This fixes a hard machine hang regression in kernel 3.16 for
boards where only pcie is active but no sata, as with this
kernel version the imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
Reported-by: NArne Ruhnau <arne.ruhnau@target-sg.com>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NArne Ruhnau <arne.ruhnau@target-sg.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The optimistic spin code assumes regular stores and cmpxchg() play nice;
this is found to not be true for at least: parisc, sparc32, tile32,
metag-lock1, arc-!llsc and hexagon.

There is further wreckage, but this in particular seemed easy to
trigger, so blacklist this.

Opt in for known good archs.
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Reported-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: stable@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/20140606175316.GV13930@laptop.programming.kicks-ass.netSigned-off-by: NIngo Molnar <mingo@kernel.org>

Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: NJiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NJiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Currently, the exynos cpuidle driver works correctly only on exynos4210
and 5250. Trying to use it with just one CPU online on any other exynos
SoCs will lead to system failure, due to unsupported AFTR mode on other
SoCs. This patch fixes the problem by registering the driver only on
supported SoCs and letting others simply use default WFI mode until
support for them is added.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adding the optional clock property for the mfc_pd for
handling the re-parenting while pd on/off.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NShaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

While powering on/off a local powerdomain in exynos5 chipsets, the
input clocks to each device gets modified. This behaviour is based
on the SYSCLK_SYS_PWR_REG registers.
E.g. SYSCLK_MFC_SYS_PWR_REG = 0x0, the parent of input clock to MFC
                             (aclk333) gets modified to oscclk
                            = 0x1, no change in clocks.
The recommended value of SYSCLK_SYS_PWR_REG before power gating any
domain is 0x0. So we must also restore the clocks while powering on
a domain everytime.

This patch adds the framework for getting the required mux and parent
clocks through a power domain device node. With this patch, while
powering off a domain, parent is set to oscclk and while powering back
on, its re-set to the correct parent which is as per the recommended
pd on/off sequence.
Signed-off-by: NPrathyush K <prathyush.k@samsung.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NShaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Currently, the coherency fabric support registers two bus notifiers;
one for platform, one for pci bus types, with the same notifier block.
However, this is illegal and can cause serious issues: the notifier
block is also a link in the notifier list and cannot be inserted twice.

This commit fixes this by using different notifier blocks (with the same
notifier callback) to set the platform and pci bus types notifiers.

Fixes: b0063aad ("ARM: mvebu: use hardware I/O coherency also for PCI devices")
Reported-by: NPaolo Pisati <p.pisati@gmail.com>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1404826657-6977-1-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

In the inline asm part of the function armada_370_xp_pmsu_idle_enter()
the input operand was used. The intent here was to let the compiler
choose this register so it could do the optimization it
needed.

However an input operand is not supposed to be modified by the inline
asm code. This can lead to improper generated instructions.

In some case generated instruction the compiler made the choice to
reuse the same register to store the return value. But in the assembly
part this register was modified, so it can lead to return an wrong
value.

The fix is to use a clobber. Thanks to this the compiler will know
that the value of this register will be modified.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404483736-16938-1-git-send-email-gregory.clement@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This code is not working currently and it can be removed. There is a
conflict in sharing resources with the actual HDMI driver and with
the ASoC HDMI audio DAI driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Let's say clock A and B are two gate clocks that share the same register
bit in hardware.  Therefore they are registered as shared gate clocks
with imx_clk_gate2_shared().

In a scenario that only clock A is enabled by clk_enable(A) while B is
not used, the shared gate will be unexpectedly disabled in hardware.
It happens because clk_enable(A) increments the share_count from 0 to 1,
while clock B is unused to clock core, and therefore the core function
will just disable B by calling clk->ops->disable() directly.  The
consequence of that call is share_count is decremented to 0 and the gate
is disabled in hardware, even though clock A is still in use.

The patch fixes the issue by initializing the share_count per hardware
state and returns enable state per share_count from .is_enabled() hook,
in case it's a shared gate.

While at it, add a check in clk_gate2_disable() to ensure it's never
called with a zero share_count.
Reported-by: NFabio Estevam <fabio.estevam@freescale.com>
Fixes: f9f28cdf ("ARM: imx: add shared gate clock support")
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Currently CLK_FOUT_EPLL was set as one of the parents of AUDSS mux.
As per the user manual, it should be CLK_MAU_EPLL.

The problem surfaced when the bootloader in Peach-pit board set
the EPLL clock as the parent of AUDSS mux. While booting the kernel,
we used to get a system hang during late boot if CLK_MAU_EPLL was
disabled.
Signed-off-by: NTushar Behera <tushar.b@samsung.com>
Signed-off-by: NShaik Ameer Basha <shaik.ameer@samsung.com>
Reported-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Almost all Exynos-series of SoCs that run in secure mode don't need
additional offset for every CPU, with Exynos4412 being the only
exception.

Tested on Origen-Quad (Exynos4412) and Arndale-Octa (Exynos5420).

While at it, fix the coding style (space around *).
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Tested-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The revision checking in l2c310_enable() was not correct; we were
masking the part number rather than the revision number.  Fix this
to use the correct macro.

Fixes: 4374d649 ("ARM: l2c: add automatic enable of early BRESP")
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently, child nodes of the gpmc node are iterated and probed
regardless of their 'status' property. This means adding 'status =
"disabled";' has no effect.

This patch changes the iteration to only probe nodes marked as
available.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The DSP platform device for TI DSP/Bridge is currently
created unconditionally whenever CONFIG_TIDSPBRIDGE is
enabled. This device should only be created on OMAP34xx/
OMAP36xx SoCs, and not for other OMAP3 derived SoCs or when
booting multi-arch images on other SoCs. So, add a check for
the SoC family both before creating the device and allocating
the carveout memory for the device.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.

Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.

The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.

This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.

CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap44xx_restart is defined as a static void inline when DRA7/AM437X is
defined alone, which implies that the restart function is no longer
functional even though it is built in. So, fix the definition of the
same.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The divider value provided to the _dpll_test_fint can reach value of
256 with J type DPLLs (USB etc.), which causes an overflow with the u8
datatype. Fix this by changing the parameter to be an int instead.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: changed type of 'n' to unsigned int]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the sysconfig class bits for the Super Speed USB
controllers
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NRajendra Nayak <rnayak@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Get rid of optional clock as that is now managed by the
AHCI platform driver.

Correct .mpu_rt_idx to 1 as the module register space (SYSCONFIG..)
is passed as the second memory resource in the device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NRajendra Nayak <rnayak@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The commit 7be914f2 {ARM: OMAP3: PRM/CM: Cleanup unused header} removed
some of the macros used by the TI DSP/Bridge driver. This fixes the
following build errors when trying to build DSP/Bridge driver (disabled
at present), otherwise results in the following build errors:

drivers/staging/tidspbridge/core/tiomap3430.c:531:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430.c:531:31: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/staging/tidspbridge/core/tiomap_io.c: In function 'sm_interrupt_dsp':
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap_io.c:414:12: error: 'OMAP3430_IVA2_DPLL_FREQSEL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:415:12: error: 'OMAP3430_EN_IVA2_DPLL_SHIFT' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap_io.o] Error 1
drivers/staging/tidspbridge/core/tiomap3430_pwr.c: In function 'dsp_clk_wakeup_event_ctrl':
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: error: 'OMAP3430_GRPSEL_GPT5_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:455:19: error: 'OMAP3430_GRPSEL_GPT6_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:468:19: error: 'OMAP3430_GRPSEL_GPT7_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:481:19: error: 'OMAP3430_GRPSEL_GPT8_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:494:19: error: 'OMAP3430_GRPSEL_MCBSP1_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:546:19: error: 'OMAP3430_GRPSEL_MCBSP5_MASK' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430_pwr.o] Error 1
make[2]: *** [drivers/staging/tidspbridge] Error 2

Fixes: 7be914f2 (ARM: OMAP3: PRM/CM: Cleanup unused header)
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This partly reverts commits 55360050 (ARM: sunxi: Remove reset code from
the platform) and 5e669ec5 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.

This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

pwm-cells should be 3. Third cell is optional PWM flags. And This flag
supported by this binding is PWM_POLARITY_INVERTED.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: NSachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Commit 1754c42e("ARM: exynos: move sysram info to exynos.c") missed
out the CONFIG_ prefix causing exynos_sysram_init() to get called twice
for SMP configurations.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: NSachin Kamat <sachin.kamat@samsug.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Without the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
532000000

With the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
266000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
133000000

The l3 clock derived from core DPLL is actually a divider clock,
with the default divider set to 2. l4 then derived from l3 is a fixed factor
clock, but the fixed divider is 2 and not 1. Which means the l3 clock is
half of core DPLLs h12x2 and l4 is half of l3 (as seen with this patch)
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTero Kristo <t-kristo@ti.com>

Conditionally compile kprobes test cases for ARMv5 instructions to avoid
compilation errors with ARMv4 targets like:

/tmp/cc7Tx8ST.s:16740: Error: selected processor does not support ARM mode `clz r0,r0'
Signed-off-by: NJon Medhurst <tixy@linaro.org>

ARM data processing instructions which have a register specified shift
are defined as UNPREDICTABLE if PC is used for any register, not just
the shift value as the code was previous assuming. This issue manifests
on A15 devices as either test case failures or undefined instructions
aborts.
Reported-by: NDavid Long <dave.long@linaro.org>
Signed-off-by: NJon Medhurst <tixy@linaro.org>

Due to a long-standing issue with Thumb symbol lookup [1] the jprobes
tests fail when built into a kernel compiled as Thumb mode. (They work
fine for ARM mode kernels or for Thumb when built as a loadable module.)

Rather than have this problem terminate testing prematurely lets instead
emit an error message and carry on with the main kprobes tests, delaying
the final failure report until the end.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2011-August/063026.htmlSigned-off-by: NJon Medhurst <tixy@linaro.org>

Commit 143e1e28 (sched: Rework sched_domain topology definition)
introduced a number of functions with a return value of 'const int'.
gcc doesn't know what to do with that and, if the kernel is compiled
with W=1, complains with the following warnings whenever sched.h
is included.

  include/linux/sched.h:875:25: warning: type qualifiers ignored on function return type
  include/linux/sched.h:882:25: warning: type qualifiers ignored on function return type
  include/linux/sched.h:889:25: warning: type qualifiers ignored on function return type
  include/linux/sched.h:1002:21: warning: type qualifiers ignored on function return type

Commits fb2aa855 (sched, ARM: Create a dedicated scheduler topology table)
and 607b45e9 (sched, powerpc: Create a dedicated topology table) introduce
the same warning in the arm and powerpc code.

Drop 'const' from the function declarations to fix the problem.

The fix for all three patches has to be applied together to avoid
compilation failures for the affected architectures.
Acked-by: NVincent Guittot <vincent.guittot@linaro.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403658329-13196-1-git-send-email-linux@roeck-us.netSigned-off-by: NIngo Molnar <mingo@kernel.org>

The SMP boot on Armada 38x and Armada 375 Z1 is currently broken in
big-endian configurations, and this commit fixes it for both
platforms.

For Armada 375 Z1, the problem was in the
armada_375_smp_cpu1_enable_code part of the code that gets copied to
the Crypto SRAM as a work-around for an issue of the Z1 stepping. This
piece of code was not switching the CPU core to big-endian, and not
endian-swapping the value read from the Resume Address register (the
value is stored little-endian). Due to the introduction of the
conditional 'rev r1, r1' instruction, the offset between the 'ldr r0,
[pc, #4]' instruction and the value it was looking is different
between LE and BE configurations. To solve this, we instead use one
'adr' instruction followed by one 'ldr'.

For Armada 38x, the problem was simply that the CPU core was not
switched to big endian in the secondary CPU startup function.

This change was tested in LE and BE configurations on Armada 385,
Armada 375 Z1 and Armada 375 A0.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404228186-21203-1-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>