The Nomadik PL080 variant has some extra protection bits that
may be set, so we need to check these bits to see if the
channels are actually available for the DMAengine to use.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Cc: Alessandro Rubini <rubini@gnudd.com>
Reviewed-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

For some reason I can't figure out we're reading the PL080_INT_STATUS
register instead of PL080_TC_STATUS when checking for the terminal
count. The PL080_INT_STATUS is a logical OR between the error and
terminal count status register and may not report what we want it
to, especially if there is an error and a terminal count at the same
time and the former is not lowered in time for the check in the TC
register. Make sure we read what we're actually interested in.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Add context parameter to device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to allow passing client/target specific information associated
with the data transfer.
Modify all affected DMA engine drivers.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Provide a common function to initialize a channels cookie values.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Now that we have the completed cookie in the dma_chan structure, we
can consolidate the tx_status functions by providing a function to set
the txstate structure and returning the DMA status.  We also provide
a separate helper to set the residue for cookies which are still in
progress.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Provide a common function to do the cookie mechanics for completing
a DMA descriptor.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Everyone deals with assigning DMA cookies in the same way (it's part of
the API so they should be), so lets consolidate the common code into a
helper function to avoid this duplication.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Add a local private header file to contain definitions and declarations
which should only be used by DMA engine drivers.

We also fix linux/dmaengine.h to use LINUX_DMAENGINE_H to guard against
multiple inclusion.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Every DMA engine implementation declares a last completed dma cookie
in their private dma channel structures.  This is pointless, and
forces driver specific code.  Move this out into the common dma_chan
structure.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Flow controller information is passed now from DMA_SLAVE_CONFIG option. This
patch makes changes in pl08x driver to use device_fc from it instead of platform
data.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Rewrite a duplicated test to test the correct value

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E;
@@

(
* E
  || ... || E
|
* E
  && ... && E
)
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Currently, if plchan->phychan is true, we return immediately from
prep_phy_chan(). We must configure txd->ccfg and increment phychan_hold before
returning. Otherwise, request line number wouldn't be configured in this txd.
Reported-by: NRajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NVinod Koul <vinod.koul@intel.com>

fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves dma/drivers/* to use new enum

Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Cc: Boojin Kim <boojin.kim@samsung.com>
Cc: Barry Song <Baohua.Song@csr.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

In pl08x_free_txd(), check if pool is allocated successfully before freeing it.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Untill now, sg_len greater than one is not supported. This patch adds support to
do that.

Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Before converting the dma channel to our private data structure, first
check that the channel is indeed one which our driver registered.  We
do this by ensuring that the underlying device is bound to our driver.

This avoids potential oopses if we try to reference 'plchan->name'
against a foreign drivers dma channel.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

pl08x_prep_channel_resources() is calling kfree() directly for txd(). To
maintain consistency in code call pl08x_free_txd() instead.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow
controller for DMA transfer. Currently DMA controller driver didn't support
peripheral flow controller configurations.

This patch adds device_fc field in struct pl08x_channel_data, which will be used
only for slave transfers and is not used in case of mem2mem transfers.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

When we have DMA transfers between peripheral and memory, then we shouldn't
reduce width of peripheral at all, as that may be a strict requirement. But we
can always reduce width of memory access, with some compromise in performance.
Thus, we must select peripheral as master and not memory.

Also this rearranges code to make it shorter.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Currently lli_len is aligned to min of two widths, which looks to be incorrect.
Instead it should be aligned to max of both widths.

Lets say, total_size = 441 bytes

MIN: lets check if min() suits or not:

CASE 1: srcwidth = 1, dstwidth = 4
min(src, dst) = 1

i.e. We program transfer size in control reg to 441.
Now, till 440 bytes everything is fine, but on the last byte DMAC can't transfer
1 byte to dst, as its width is 4.

CASE 2: srcwidth = 4, dstwidth = 1
min(src, dst) = 1

i.e. we program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
So, here too 1 byte is left, but on the source side.

MAX: Lets check if max() suits or not:

CASE 3: srcwidth = 1, dstwidth = 4
max(src, dst) = 4

Aligned size is 440

i.e. We program transfer size in control reg to 440.
Now, all 440 bytes will be transferred without any issues.

CASE 4: srcwidth = 4, dstwidth = 1
max(src, dst) = 4

Aligned size is 440

i.e. We program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
Now, also all 440 bytes will be transferred without any issues.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.

Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.

Below is summary of mail exchange with them:

[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.

[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.

So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:

        Total transfer size
        ------------------- = 40
          <source width>

[Viresh] Will this change if source is 4 bytes and dest is 2?

[David] Yes - the calculation then becomes:

        Total transfer size
        ------------------- =20
          <source width>

Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.

This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Pl080 Manual says: "Bursts do not cross the 1KB address boundary"

We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.

Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"

What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.

[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.

The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.

Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Currently, if error interrupt occurs, nothing is done in interrupt handler (just
clearing the interrupts). We must somehow indicate this to the user that DMA is
over, due to ERR interrupt or TC interrupt.

So, this patch just schedules existing tasklet, with a print showing error
interrupt has occurred on which channels.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

We have just executed following in pl08x_get_phy_channel():
	ch->signal = -1;

We don't have to compare "ch->signal < 0", as this will always be true.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits.
Also as per manual, for bit 3-31 of DMACConfiguration register:
"read undefined, write as 0"

So, we must not rely on values read from this registers bit 3-31.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in
to action where used.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

For 8 memory and 16 slave channels 35 boot print lines are printed. And that is
too much. Most of this would be more useful for debugging. So moving few of them
to dev_dbg instead of dev_info. Now only 3 prints will be printed.

This also rearrange one of the debug message to fit into two lines.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Similar comment is present over routine also pl08x_choose_master_bus(). Keeping
one of them. Also rewrite that comment to convey message clearly.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

As mentioned in Documentation/CodingStyle,

The preferred form for passing a size of a struct is the following:
   p = kmalloc(sizeof(*p), ...);

The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not.

This patch replaces (struct xyz) with *ptr at several occurrences in driver.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Header files included in driver are not present in alphabetical order. Rearrange
them in alphabetical order.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Something changed during the 3.1 merge window in the include files
which now causes the pl08x DMA engine driver to fail to build.  Fix
this by adding the now necessary dma-mapping.h include:

drivers/dma/amba-pl08x.c: In function ■pl08x_unmap_buffers■:
drivers/dma/amba-pl08x.c:1524: error: implicit declaration of function ■dma_unmap_single■
drivers/dma/amba-pl08x.c:1527: error: implicit declaration of function ■dma_unmap_page■
Acked-by: NVinod Koul <vinod.koul@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pl08x_width function does not handle rest of enums for DMA_SLAVE_BUSWIDTH_xxxx
which causes gcc to emit below warining

drivers/dma/amba-pl08x.c: In function 'pl08x_width':
	drivers/dma/amba-pl08x.c:1119: warning: enumeration value
	'DMA_SLAVE_BUSWIDTH_UNDEFINED' not handled in switch
	drivers/dma/amba-pl08x.c:1119: warning: enumeration value
	'DMA_SLAVE_BUSWIDTH_8_BYTES' not handled in switch

this patch adds a default case which returns error
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Now that we have separate cctl values for M>P and P>M transfers, we can
avoid calculating the cctl value each time we prepare a transaction.
Move the bus selection and increment setting to the slave configuration
and initialization functions.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Store the source/destination slave address separately into the channel
structure.  This moves us towards being able to avoid a configuration
call each time we use the channel.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>