Fixed a problem with the internal Owner ID allocation and
deallocation mechanisms for control method execution and
recursive method invocation.  This should eliminate the
OWNER_ID_LIMIT exceptions and "Invalid OwnerId" messages
seen on some systems.  Recursive method invocation depth
is currently limited to 255.  (Alexey Starikovskiy)

http://bugzilla.kernel.org/show_bug.cgi?id=4892

Completely eliminated all vestiges of support for the
"module-level executable code" until this support is
fully implemented and debugged.  This should eliminate the
NO_RETURN_VALUE exceptions seen during table load on some
systems that invoke this support.

http://bugzilla.kernel.org/show_bug.cgi?id=5162

Fixed a problem within the resource manager code where
the transaction flags for a 64-bit address descriptor were
handled incorrectly in the type-specific flag byte.

Consolidated duplicate code within the address descriptor
resource manager code, reducing overall subsystem code size.
Signed-off-by: NRobert Moore <Robert.Moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAlexey Y. Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NYann Droneaud <ydroneaud@mandriva.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Implemented a full bytewise compare to determine if a table load
request is attempting to load a duplicate table. The compare is
performed if the table signatures and table lengths match. This
will allow different tables with the same OEM Table ID and
revision to be loaded.

Although the BIOS is technically violating the ACPI spec when
this happens -- it does happen -- so Linux must handle it.
Signed-off-by: NRobert Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds back the code that was taken out, thus re-enabling:

* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer

This patch is used by the gianfar driver, and other drivers which are in
development.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Bugfix (usage of uninitialized pointer in zfcp_port_dequeue) and compile
fixes for the zfcp device driver.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NJames Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

struct zfcp_port::scsi_id was removed by commit
  3859f6a2Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

[ Same race and same patch also by Steven Rostedt <rostedt@goodmis.org> ]

I have a laptop (G3 powerbook) which will pretty reliably hit a race
between con_open and con_close late in the boot process and oops in
vt_ioctl due to tty->driver_data being NULL.

What happens is this: process A opens /dev/tty6; it comes into
con_open() (drivers/char/vt.c) and assign a non-NULL value to
tty->driver_data.  Then process A closes that and concurrently process
B opens /dev/tty6.  Process A gets through con_close() and clears
tty->driver_data, since tty->count == 1.  However, before process A
can decrement tty->count, we switch to process B (e.g. at the
down(&tty_sem) call at drivers/char/tty_io.c line 1626).

So process B gets to run and comes into con_open with tty->count == 2,
as tty->count is incremented (in init_dev) before con_open is called.
Because tty->count != 1, we don't set tty->driver_data.  Then when the
process tries to do anything with that fd, it oopses.

The simple and effective fix for this is to test tty->driver_data
rather than tty->count in con_open.  The testing and setting of
tty->driver_data is serialized with respect to the clearing of
tty->driver_data in con_close by the console_sem.  We can't get a
situation where con_open sees tty->driver_data != NULL and then
con_close on a different fd clears tty->driver_data, because
tty->count is incremented before con_open is called.  Thus this patch
eliminates the race, and in fact with this patch my laptop doesn't
oops.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
[ Same patch
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
  in http://marc.theaimsgroup.com/?l=linux-kernel&m=112450820432121&w=2 ]
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes a severe problem with 2.6.13-rc7.

Due to recent SCSI changes it is not possible to add any LUNs to the zfcp
device driver anymore.  With registration of remote ports this is fixed.
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Acked-by: NJames Bottomley <jejb@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I know that scsi procfs is legacy code but this is a fix for a memory leak.

While reading through sg.c I realized that the implementation of
/proc/scsi/sg/devices with seq_file is leaking memory due to freeing the
pointer returned by the next() iterator method.  Since next() might return
NULL or an error this is wrong.  This patch fixes it through using the
seq_files private field for holding the reference to the iterator object.

Here is a small bash script to trigger the leak. Use slabtop to watch
the size-32 usage grow and grow.

#!/bin/sh

while true; do
	cat /proc/scsi/sg/devices > /dev/null
done
Signed-off-by: NJan Blunck <j.blunck@tu-harburg.de>
Acked-by: NJames Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fixed race between submitting streaming URBs in the driver and starting
the actual transfer in hardware (demodulator and USB controller) which
sometimes lead to garbled data transfers. URBs are now submitted first,
then the transfer is enabled. Dibusb devices and clones are now fully
functional again.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes a bug in the capifs initialization code, where the
filesystem is not unregistered if kern_mount() fails.
Signed-off-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When acpi_sleep_prepare was moved into a shutdown method we
started calling it for all shutdowns.

It appears this triggers some systems to power off on reboot.

Avoid this by only calling acpi_sleep_prepare if we are going to power
off the system.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Both revisions share the same PCI device ID and vendor ID but revision 2
of the device uses SysKonnect's chipset whereas revision 3 of the device
uses Realtek's 8169 chipset.

Credit goes to Christiaan Lutzer <mythtv.lutzer@gmail.com> for reporting
the issue and giving the actual value for the different revisions.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Rewrite the mkiss driver to make it SMP-proof following the example of
6pack.c.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't check type of sax25_family; dev_set_mac_address has already done
that before and anyway, the type to check against would have been
ARPHRD_AX25.  We only got away because AF_AX25 and ARPHRD_AX25 both happen
to be defined to the same value.

Don't check sax25_ndigis either; it's value is insignificant for the
purpose of setting the MAC address and the check has shown to break
some application software for no good reason.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

I dropped the timer initialization bits by accident when sending the
p-persistence fix.  This patch gets the driver to work again on halfduplex
links.
Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix bugs for unlikely edge cases noticed by Douglas Gilbert:

- When READ(6)/WRITE(6) sector count == 0, treat it as 256 sectors

- For other READ(x)/WRITE(x), when sector count == 0, error.
  We don't support successfully completing zero-length transfers at
  this time.

Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Currently we may have work scheduled in default kernel workqueue when
the device is going down.  The device could get freed before this
workqueue gets serviced.  I am actually seeing this causing system
hangs.

The following patch fixes this by using ipoib_workqueue which gets
flushed when the device is going down.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add handling for ABORT / STOP RMPP MADs.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix deadlock condition resulting from trying to destroy a cm_id
from the context of a CM thread.  The synchronization around the
ucm context structure is simplified as a result, and some simple
code cleanup is included.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Always make sure that the full membership bit is set in the P_Keys
that IPoIB uses.  This makes sure that all hosts join the correct
multicast groups so that hosts that are partial partition members
can talk to the rest of the network.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add mthca support for shared receive queues (SRQs),
including userspace SRQs.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When creating a table in context memory where the table is smaller
than our chunk size, we don't want to allocate and map a full chunk.
Instead, allocate just enough memory to cover the table.

This can be pretty simple because all tables are a power-of-2 size, so
either the table is a multiple of the chunk size, or it's smaller than
one chunk.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Move the definitions of the WQE structures from mthca_qp.c into
mthca_wqe.h, so that we'll be able to share them when we add the
SRQ code in mthca_srq.c.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Mem-free HCAs never generate error CQEs that complete multiple WQEs,
so just skip the call to mthca_free_err_wqe() for them rather than
having logic to handle the mem-free case in mthca_free_err_wqe().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clean up the allocation of memory for queues by factoring out the
common code into mthca_buf_alloc() and mthca_buf_free().  Now CQs and
QPs share the same queue allocation code, which we'll also use for SRQs.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add SRQ support to userspace verbs module.  This adds several commands
and associated structures, but it's OK to do this without bumping the
ABI version because the commands are added at the end of the list so
they don't change the existing numbering.  There are two cases to
worry about:

1. New kernel, old userspace.  This is OK because old userspace simply
   won't try to use the new SRQ commands.  None of the old commands are
   changed.

2. Old kernel, new userspace.  This works perfectly as long as
   userspace doesn't try to use SRQ commands.  If userspace tries to
   use SRQ commands, it will get EINVAL, which is perfectly
   reasonable: the kernel doesn't support SRQs, so we couldn't do any
   better.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make the required core API additions and changes for
shared receive queues (SRQs).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set the max_msg_sz port property correctly in mthca's port_query
function.  Also zero out the attr struct so that we don't leave
any other members uninitialized.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we call the INIT_IB firmware command to bring up a port, use
the actual port width capability returned by the QUERY_DEV_LIM
command instead of always trying to enable both 1X and 4X.  This
fixes breakage seen when the firmware is build to allow 4X only.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Remove unneeded includes of <linux/version.h>.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Change ib_mad_thread_completion_handler to conform to ib_comp_handler
declaration.
Signed-off-by: NHal Rosenstock <halr@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Use the generic key_to_hw_index() function instead of the Arbel-specific
version in mthca_free_region().
Signed-off-by: NGuy German <guyg@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make sure that all FMRs are unmapped before we deallocate them so that
we don't leak references to our protection domain when destroying an
FMR pool.  (Bug reported by Guy German <guyg@voltaire.com>)
Signed-off-by: NRoland Dreier <rolandd@cisco.com>