They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.

CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdf
http://download.intel.com/design/Pentium4/specupdt/30235221.pdf

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Compute the highest possible value for memnode_shift, in order to reduce
footprint of memnodemap[] to the minimum, thus making all users
(phys_to_nid(), kfree()), more cache friendly.

Before the patch :

 Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
 Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
 Using 23 for the hash shift. Max adder is 3ffffffff

After the patch :

 Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
 Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
 Using 33 for the hash shift.

In this case, only 2 bytes of memnodemap[] are used, instead of 2048
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This allows to run 64bit signal handlers in 64bit processes that run small
code snippets in compat mode.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs.  The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)

The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports.  So the old code just assumed all, which would
lead to this memory wastage.

This implements some new heuristics:

 - If the BIOS specified disabled CPUs in the ACPI/mptables assume they
   can be enabled later (this is bending the ACPI specification a bit,
   but seems like a obvious extension)
 - The user can overwrite it with a new additionals_cpus=NUM option
 - Otherwise use half of the available CPUs or 2, whatever is more.

Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Minor victory on the continuous quest against all stray extern.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Minor cleanup - remove obsolete extern
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.

This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped.  Druing boot, all the processors will use this as their
level4 pgt.  On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses.  On AP's we will zap the low mappings as
soon as we jump to C code.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.

This also adds a generic numa_node_id to all the topology includes

Suggested by Eric Dumazet
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix

  arch/x86_64/kernel/aperture.c: In function #iommu_hole_init#:
  arch/x86_64/kernel/aperture.c:199: warning: #aper_order# may be used uninitialized in this function
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.

AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove duplicate __cpuinit in smp.c. Already defined in init.h which is
already included.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI.  It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.

The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540.  This is much bigger
than NR_IRQS (224 for both i386 and x86_64).  Also, there aren't enough
vectors to go around.  There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F.  So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.

Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.

bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.

APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.

AK: added some ifdefs to make it compile on UP
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The VM needs to know about lost memory in zones to accurately
balance dirty pages. This patch accounts mem_map in there too,
which fixes a constant errror of a few percent. Also some
other misc mappings and the kernel text itself are accounted
too.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The code should deal with an additional empty zone, so fix up the
#error.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

IA64 traditionally had a 4GB DMA32 zone. Set the compatibility flag
to keep old drivers working.

For new drivers it would be better to use ZONE_DMA32 now.

Cc: tony.luck@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.

As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone.  We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.

But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.

So this patch adds both zones.

This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.

Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata).  They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices.  With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.

One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.

The new zone is so far added only for x86-64.

For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.

One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64  use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.

These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rerun and enable autofs 4, relayfs and softdog
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit.  With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000.  Oops.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

No longer maintained

Patch from Nicolas Pitre

We have an optimized sha1 routine (arch/arm/lib/sha1.S) meant to
override the generic one in lib/sha1.c.

Unfortunately lib/lib.a is listed _before_ arch/arm/lib/lib.a in the
link argument list and therefore the architecture specific lib functions
are not picked up before the generic versions.

This patch is a quick fix to change that ordering for ARM.  Here's what
the kbuild maintainer had to say about it (was also CC'd on lkml):

On Wed, 2 Nov 2005, Sam Ravnborg wrote:
> This looks like an obvious way to achive correct ordering.
> We could change it so arch defines always took precedence but
> the above is so simple that it is not worth the effort.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Todd Poynor

Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Dave Jiang

This provides support for IXP2xxx error interrupt handling. Previously there was a patch to remove this (although the original stuff was broken). Well, now the error bits are needed again. These are used extensively by the micro-engine drivers according to Deepak and also we will need it for the new EDAC code that Alan Cox is trying to push into the main kernel.

Re-submit of 3072/1, generated against git tree pulled today. AFAICT, this git tree pulled in all the ARM changes that's in arm.diff. Please let me know if there are additional changes. Thx!
Signed-off-by: NDave Jiang <djiang@mvista.com>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

ARM processors that have pld instructions are not using those copy_user
implementation anymore.  Let's remove the useless PLD lines which were
half wrong anyway.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

IXDP2401 config file has wrong baudrate and both boards have 3 UARTs.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Using a llx format to print addresses that might possibly be (only) 36
bits wide make sense.  However making it a zero padded 16 char wide
field is a bit excessive and useless.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The 'K' extension adds several new instructions to the ARMv6 ISA
which are primerily useful for SMP.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

register_vpa() doesn't actually do a VPA register call it just uses the flags
you pass it, so rename it to vpa_call() to be clearer.

We can then define register_vpa() and unregister_vpa() which are both simple
wrappers around vpa_call(). (we'll need unregister_vpa() for kexec soon)

We can then cleanup vpa_init(), and because vpa_init() is only called from
platforms/pseries we remove the definition in asm-ppc64/smp.h.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

This adds missing header and thus fix the warning issued by ming prototype.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Current comment on top of m8xx_cpm_dpinit is wrong.
Signed-off-by: NMarcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes these warnings:

      Building modules, stage 2.
      MODPOST
    *** Warning: "__ide_mm_insl" [drivers/ide/ide-core.ko] undefined!
    *** Warning: "__ide_mm_outsw" [drivers/ide/ide-core.ko] undefined!
    *** Warning: "__ide_mm_insw" [drivers/ide/ide-core.ko] undefined!
    *** Warning: "__ide_mm_outsl" [drivers/ide/ide-core.ko] undefined!
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently there is no Kconfig symbol to indicate that we want nvram
support on 64-bit kernels; it's assumed we always want it, so make
the powermac setup code always initialize the pmac nvram code if
64-bit.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The latest updates to bug.h generate build warnings in traps.c in
arch/ppc.  Fix print format specifiers to account for change of line type
to long from int.
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>