This patch adds a compatible string to support for R-Car E2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>" in patch 2
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the HSUSB controllers of R-Car Gen2 are the same specification
(they have 16 pipes and usb-dmac), this patch changes USBHS_TYPE_R8A7790
and USBHS_TYPE_R8A7791 to USBHS_TYPE_RCAR_GEN2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ffs_closed can race with configfs_rmdir which will call config_item_release, so
add an extra check to avoid calling the unregister_gadget_item with an null
gadget item.
Signed-off-by: NRui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: NSubbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to return error to caller if command is not sent to
controller succesfully.
Signed-off-by: NSubbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Fixes: b09bb642 (usb: dwc3: gadget: implement Global Command support)
Cc: <stable@vger.kernel.org> #v3.5+
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.

The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

After the renesas_usbhs driver is enabled in ARM multi_v7_defconfig,
we now get a new warning:

renesas_usbhs/mod.c: In function 'usbhs_interrupt':
renesas_usbhs/mod.c:246:7: warning: 'intenb1' may be used uninitialized in this function [-Wmaybe-uninitialized]

gcc correctly points to a problem here, for the case that the
device is in host mode, we use the intenb1 variable without
having assigned it first. The state->intsts1 has a similar
problem, but gcc cannot know that.

This avoids the problem by initializing both sides of the
comparison to zero when we don't read them from the respective
registers.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 88a25e02 ("usb: renesas_usbhs: Add access control for INTSTS1 and INTENB1 register")
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

rndis_get_nr() returns either a non-negative value on success
or a negative value on failure. In case of failure an error code
is returned to the caller of rndis_register().
If the "i" is unsigned, the information about error from rndis_get_nr()
is lost. If there is no error but rndis_get_nr() returns a value greater
than 256 the least significant bits of i are zero effectively limiting the
number of configs to 256.

This patch fixes that.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If CONFIG_USB_GADGET_DEBUG_FILES is set then a block is opened and inside
it there is a local variable "i" which hides the "i" local to the
rndis_deregister(). Consequently, a random value is formatted
into the "name" buffer.

This patch removes the block-local i.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The patch:

83210e59
usb: gadget: rndis: use rndis_params instead of configNr

should change all invocations of rndis_signal_(dis)connect().
This patch fixes that.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

INTSTS1 and INTENB1 register of renesas_usbhs can access only Host mode.
This adds process of accessing INTSTS1 and INTENB1 only when renesas_usbhs
is Host mode.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

TUSB1210 ULPI PHY has vendor specific register for eye
diagram tuning. On some platforms the system firmware has
set optimized value to it. In order to not loose the
optimized value, the driver stores it during probe and
restores it every time the PHY is powered back on.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ULPI PHYs need to be bound to their controllers with a
lookup. This adds helpers that the ULPI drivers can use to
do both, the registration of the PHY and the lookup, at the
same time.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Registers DWC3's ULPI interface with the ULPI bus when it's
available.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On some BYT platforms the USB2 PHY needs to be put into
operational mode by the controller driver with GPIOs
controlling the PHYs reset and cs signals.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This allows dwc3_phy_setup() to be more useful later. There
is nothing preventing the PHY configuration registers from
being programmed early. They do not loose their context in
soft reset.

There are however other PHY related operations that should
be executed before the driver request handles to the PHYs,
such as registering DWC3's ULPI interface, which can now be
done in dwc3_phy_setup().

Also, if there ever was need for the two 100ms delays in
dwc3_phy_setup() there isn't anymore. The PHYs are now reset
after the PHY interfaces are setup.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So it can be called from other places later.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So they are available when ULPI interface support is added.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to store it before phys are handled, so we can later
use it in ULPI interface support code.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make selection between ULPI and UTMI+ interfaces possible by
providing definition for the bit in Global USB2 PHY
Configuration Register that controls it.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Definitions for Global USB2 PHY Vendor Control Register
bits. We will need them to access ULPI PHY registers later.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.

There are two major issues that the bus type is meant to
tackle:

Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.

Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit db62b9a8 (usb: dwc2: host: don't
use dma_alloc_coherent with irqs disabled)
introduced a build warning by using NULL
as an integer. Fix that by just using 0 instead
of NULL.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add a debugfs interface - softconnect - for host mode to
connect/disconnect the devices without physically remove the
them.

This adds the capability to re-enumerate the devices which are
permanently mounted on the board with the MUSB controller
together.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.

This patch allocates struct rndis_params on demand in rndis_register().
Coversly, the structure is free()'d in rndis_deregister().
If CONFIG_USB_GADGET_DEBUG_FILES is set, the proc files are created which
is the same behaviour as before, but the moment of creation is delayed
until struct rndis_params is actually allocated.

rnids_init() and rndis_exit() have nothing to do, so they are eliminated.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Don't use a space between function name and parameter list opening bracket.
All other functions in this file comply wich checkpatch rules.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.

This patch prepares the elimination of the said limit by converting all the
functions which accept rndis config number to accept a pointer to the
actual struct rndis_params. Consequently, rndis_register() returns
a pointer to a corresponding struct rndis_params instance. The pointer
is then always used by f_rndis.c instead of config number when it talks
to rndis.c API.

A nice side-effect of the changes is that many lines of code in rndis.c
become shorter and fit in 80 columns.

If a function prototype changes in rndis.h a style cleanup is made
at the same time, otherwise checkpatch complains that the patch
has style problems.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using unnecessary static char buffers isn't good.
Use the %pV extension instead.

Miscellanea:

o the dprintk return value is unused, make it void
o add __printf format and argument verification
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is a subtle typo phys-names should be phy-names. Using the
current example means you don't have working usb (as you fail to
obtain the phys). Also update the example to use the generic phy
type constants which are now used for miphy28.

Additionally also remove the unnecessary new line in the example.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove ifdefs for musb_host_rx to get closer to building in
all the DMA drivers.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can remove the ifdefs by setting up helper functions for
mentor DMA and cppi/tusb DMA.

Note that I've kept the existing formatting as otherwise this
patch becomes pretty much unreadable.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Let's get rid of the horrible ifdef in middle of the expression.
We can do it by adding a variable for short_packet and testing
it separately for DMA related code.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

For musb_core.c we can now just drop the DMA related
ifdef and use the already existing runtime test for
!is_cppi_enabled(musb) instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>