Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: NKenneth Westfield <kwestfie@codeaurora.org>
Acked-by: NBanajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

After commit b2b49ccb (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under sound/.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NNicolin Chen <nicoleotsuka@gmail.com>
Acked-by: NBrian Austin <brian.austin@cirrus.com>
Acked-by: NMark Brown <broonie@kernel.org>

The codec driver uses regmap to do i2c read/write.
The codec driver started to use REGMAP_IRQ since:

5e3363ad
ASoC: rt5677: add GPIO IRQ support
Signed-off-by: NBen Zhang <benzh@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

If no one defined the rt5645->pdata.hp_det_gpio in coreboot/bios.
It will cause kernel to reboot because rt5645->pdata.hp_det_gpio
is 0. So it is worth to add a check in rt5645_jack_detect.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NFang, Yang A <yang.a.fang@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When the codec is connected using i2c, it will only auto-increment
register addresses if msb (0x80) of the register address byte is set.

[Fixes cache sync if multiple adjacent registers are updated -- broonie]
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Commit d74bcaae (ASoC: wm5102: Move ultrasonic response settings
lock to the driver level) created a driver local mutex for protecting
the ultrasonic response settings but neglected to initialize that mutex,
causing loud complaints from lockep and potential runtime failures. Fix
this by initializing the mutex.
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>

The volume blocks have an step of 0.375dB, but TLV uses 0.01dB for
units.  Only use the resolution supported, ignoring the LSB of the
volume register.  This results in half the steps and 0.75dB per step,
but reports accurate levels through TLV.  Update the masks to reflect
that these are registers have the LSB ignored.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

When trying to play a 8kHz file with codec in slave mode we get the following
error on a mx28evk:

$ aplay -Dhw:0,0 stereo_8k.wav
Playing WAVE 'stereo_8k.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
[   21.218647] sgtl5000 0-000a: PLL not supported in slave mode
[   21.224559] sgtl5000 0-000a: 128 ratio is not supported. SYS_MCLK needs to be 256, 384 or 512 * fs
[   21.233687] sgtl5000 0-000a: ASoC: can't set sgtl5000 hw params: -22
aplay: set_params:1123: Unable to install hw params:

This error happens because we are using 'sys_fs' instead of 'frame_rate' in the
valid ratio check.

Use the real'frame_rate' so that the ratio is correctly calculated and the
playback can run.

sgtl5000 codec manual states that in 'Synchronous SYS_MCLK input' mode that the
following SYS_CLK frequencies are allowed: 256*fs, 384*fs, 512*fs.

, where fs is the sampling frequency, which can be in the range of:
8, 11.025, 16, 22.5, 32, 44.1, 48, 96 kHz.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.

When running the codec as slave, the master should generate MCLK in the range of
256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK input mode.

In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.

Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Remove the manual transition back to SND_SOC_BIAS_STANDBY in resume. This
is already be automatically handled by the ASoC core.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. While we are at it also remove the unused codec field from
the cq93vc struct so the whole probe function can be removed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

The "changed" variable should be set to false at the start.

Fixes: a35daac7 ('ASoC: sigmadsp: Add support for fw v2')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>

We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: NZidan Wang <b50113@freescale.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

After the patch "ASoC: rt5677: Use specific r/w function for DSP mode", the
regmap_range "rt5677_ranges" was not registered in rt5677_regmap_physical, and
it caused that the regmap_range "rt5677_ranges" cannot be accessed by the
specific r/w function. The patch fixes this issue.
Signed-off-by: NOder Chiou <oder_chiou@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch will enable ASRC for DMIC if ASRC is useable.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To use ASRC, the sysclk should be faster than 384 times sample rate of I2S1.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

There are 3 JD modes in RT5645. This patch configure register
values according to platform data.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

sound/soc/codecs/sigmadsp.c:656:1-4: WARNING: end returns can be simpified and declaration on line 636 can be dropped

 Simplify a trivial if-return sequence.  Possibly combine with a
 preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Fix off by one read beyond the end of a table.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend. This makes the code a bit shorter and cleaner.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the regcache_mark_dirty()
from the suspend handler since it is already called by the ASoC core.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.

Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.

The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@kernel.org>