Fix tx gain table index on fast channel change for AR953x.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean ucode selection, fix choice of firmware for LCN, drop some goto-s,
add new devices.
Tested on 14e4:4312, 14e4:4315, 14e4:4328, 14e4:432b, 14e4:4353.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For consistency with other drivers, replace a magic number by a macro.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For consistency with other drivers, replace a magic number by a macro.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: NPeter Wu <peter@lekensteyn.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for external PA and clean code a bit.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The users of the fwil put an error message in the log so there is
no need to do the same in the lower level functions in fwil when
the firmware on the device returns an error. Some errors can be
ignored for the driver to function and this will avoid driver users
to point at the low-level error message as potential bug.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of controlling mpc setting during scan operation, initialize
mpc setting and then let firmware take care of it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NDaniel Kim <dekim@broadcom.com>
[arend@broadcom.com: keep mpc setting for bcm4329]
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All log messages were set to TRACE level, which is intended
for function entry and exit. Using INFO instead in other
places. Also reducing an error message that always popped
up upon module unload.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Passing a pointer from user space and using it directly in driver is not a
preferable behavior. Switch to cfg80211 vendor mode for dongle command for
better cross platform compatibility.
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the USB devices also have Bluetooth inside. These devices
can with specific firmware result in a composite USB device. This
change will update the driver such that it will also accept the
correct interface of composite devices. It is backward compatible
with old non-composite USB fw.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After updating 2G bandwidth capability clear ht info. This will be properly
set upon calling brcmf_update_wiphy_bands().
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the USB 43566 device to the supported devices list. The 43566
is a WiFi-only variant of the 43569. It uses the same FW as 43569.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added usb device id for the new device 43569 to the list of
supported devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Applying ++ to a bool is equivalent to setting it true, regardless of
its initial value (bools are not uint1_t). Hence the function
wl_get_vif_state_all can only ever return true/false. The only in-tree
caller uses its return value as a boolean. So update its return type,
and since the list traversal and bit testing have no side effects,
just return true immediately. Its return value tells if any vif is in
the specified state, so also rename it to brcmf_get_vif_state_any.

Reviewed-by: Arend van Spriel<arend@broadcom.com>
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sleep Confirm command is sent separately while other commands
are handled through cmd_pending_q. Print sleep_confirm cmd and
its response as well as power save events so that we have a
clearer picture of power save handshake in driver log.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates mwifiex Copyright to 2014.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some SDIO controllers do not support MMC_PM_KEEP_POWER properly.
To test host sleep feature without putting the system into sleep
we need to simulate host sleep configuration & handshake between
driver and firmware using customized parameters.
This patch adds hscfg debugfs item, with which user could change
host sleep parameters for debugging.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware dump feature is added for SDIO based chipsets
which can be used with the help of ethtool commands.

1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff

When the operation is completed, udev event will be sent to
trigger external application.

2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_sdio", ACTION=="change", RUN+="/sbin/mwifiex_sdio_fw_dump.sh"

mwifiex_sdio_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log

ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log

ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log

ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/APU.log

ethtool --set-dump mlan0 4
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/CIU.log

ethtool --set-dump mlan0 5
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ICU.log

ethtool --set-dump mlan0 6
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As we can derive host pointer from adapter, maintaining
a global variable doesn't make sense.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Existing dedicated card_reset work queue is replaced with the
interface specific workqueue pointer provided by mwifiex module.
Also new work flag is added for card reset task.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware dump feature is added for PCIe based chipsets which can
be used with the help of ethtool commands.

1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff

When the operation is completed, udev event will be sent to
trigger external application.

2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_pcie", ACTION=="change", RUN+="/sbin/mwifiex_pcie_fw_dump.sh"

mwifiex_pcie_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log

ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log

ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log

ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/IRAM.log
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver is now responsible for veryfing if the
switch is possible.

Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().

This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).

It is now safe to call ieee80211_chswitch_done()
more than once.

Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel switch finalization is now 2-step. First
step is when driver calls csa_finish(), the other
is when reservation is actually finalized (which
can be deferred for in-place reservation).

It is now safe to call ieee80211_csa_finish() more
than once.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ieee80211_check_combinations() computes
radar_detect accordingly depending on chanctx
reservation status.

This makes it possible to use the function for
channel_switch validation.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.

Such reservations are not finalized until all
assigned interfaces are ready.

This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.

This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).

As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the device fails during a restart, mac80211 now handles the
situation better but we still have a little bit of cleanup to
do in the driver - add the required code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NArikX Nemtsov <arik@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the new API allows multiple priorities, we need to
properly set the beacon's prorities in the TX cmd associated
to it.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use extended beacon notification when supported by FW.
Set last beacon system time to AP or GO interface.
System time of last beacon can be used to avoid TBTT overlapping
between two interfaces, CSA and other uses.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>