VxLAN offloading is not functional if the NIC is running in multichannel
mode (UMC, FLEX-10, VNIC...). Enabling this additionally kills whole
connectivity through the NIC and the device needs to be down and up to
restore it. The firmware should take care about it and does not allow
the conversion of interface to tunnel type (be_cmd_manage_iface) or should
support VxLAN offloading if multichannel config is enabled.
I have tested this on the latest available firmware (10.6.144.21).

Result:
[root@sm-04 ~]# ip link set enp5s0f0 up[root@sm-04 ~]# ip addr add 172.30.10.50/24 dev enp5s0f0
[root@sm-04 ~]# ping -c 3 172.30.10.254PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
64 bytes from 172.30.10.254: icmp_seq=1 ttl=64 time=0.317 ms
64 bytes from 172.30.10.254: icmp_seq=2 ttl=64 time=0.187 ms
64 bytes from 172.30.10.254: icmp_seq=3 ttl=64 time=0.188 ms

 --- 172.30.10.254 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 0.187/0.230/0.317/0.063 ms
[root@sm-04 ~]# ip link add link enp5s0f0 vxlan10 type vxlan id 10 remote 172.30.10.60 dstport 4789
[root@sm-04 ~]# ip link set vxlan10 up
[ 7900.442811] be2net 0000:05:00.0: Enabled VxLAN offloads for UDP port 4789
[ 7900.455722] be2net 0000:05:00.1: Enabled VxLAN offloads for UDP port 4789
[ 7900.468635] be2net 0000:05:00.2: Enabled VxLAN offloads for UDP port 4789
[ 7900.481553] be2net 0000:05:00.3: Enabled VxLAN offloads for UDP port 4789
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.

 --- 172.30.10.254 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms

[root@sm-04 ~]# ip link set vxlan10 down
[ 7959.434093] be2net 0000:05:00.0: Disabled VxLAN offloads for UDP port 4789
[ 7959.444792] be2net 0000:05:00.1: Disabled VxLAN offloads for UDP port 4789
[ 7959.455592] be2net 0000:05:00.2: Disabled VxLAN offloads for UDP port 4789
[ 7959.466416] be2net 0000:05:00.3: Disabled VxLAN offloads for UDP port 4789
[root@sm-04 ~]# ip link del vxlan10
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.

 --- 172.30.10.254 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 1999ms

[root@sm-04 ~]# ip link set enp5s0f0 down
[root@sm-04 ~]# ip link set enp5s0f0 up
[ 8071.019003] be2net 0000:05:00.0 enp5s0f0: Link is Up
[root@sm-04 ~]# ping -c 3 172.30.10.254
PING 172.30.10.254 (172.30.10.254) 56(84) bytes of data.
64 bytes from 172.30.10.254: icmp_seq=1 ttl=64 time=0.318 ms
64 bytes from 172.30.10.254: icmp_seq=2 ttl=64 time=0.196 ms
64 bytes from 172.30.10.254: icmp_seq=3 ttl=64 time=0.194 ms

 --- 172.30.10.254 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 0.194/0.236/0.318/0.057 ms

Cc: Sathya Perla <sathya.perla@avagotech.com>
Cc: Ajit Khaparde <ajit.khaparde@avagotech.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NAjit Khaparde <ajit.khaparde@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma_mapping_error() function returns true or false.  We should
return -ENOMEM if it there is a dma mapping error.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed.  In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.

Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY.  Closing and re-opening the interface would
restore the MAC link parameters to the correct values.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current filer rule optimization is broken in several ways:
 (1) Can perform reads/writes beyond end of allocated tables.
     (gianfar_ethtool.c:1326).

(2) It breaks badly for rules with more than 2 specifiers
     (e.g. matching ip, port, tos).

Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND         Q:00           ctrl:00000080 prop:00000210
01: FPR  == 00000210 AND CLE     Q:00           ctrl:00000281 prop:00000210
02: MASK == ffffffff AND         Q:00           ctrl:00000080 prop:ffffffff
03: DPT  == 00000003 AND         Q:00           ctrl:0000008e prop:00000003
04: TOS  == 00000003 AND         Q:00           ctrl:0000008a prop:00000003
05: DIA  == 0a000003 AND         Q:11           ctrl:0000448c prop:0a000003
06: DPT  == 00000002 AND         Q:00           ctrl:0000008e prop:00000002
07: TOS  == 00000002 AND         Q:00           ctrl:0000008a prop:00000002
08: DIA  == 0a000002 AND         Q:09           ctrl:0000248c prop:0a000002
09: DIA  == 0a000001 AND         Q:00           ctrl:0000008c prop:0a000001
0a: DPT  == 00000001 AND         Q:00           ctrl:0000008e prop:00000001
0b: TOS  == 00000001     CLE     Q:01           ctrl:0000060a prop:00000001
ff: MASK >= 00000000             Q:00           ctrl:00000020 prop:00000000

(Entire cluster gets AND-ed together).

 (3) We observed that the masking rules it generates do not
     play well with clustering on P2020.  Only first rule
     of the cluster would ever fire.  Given that optimizer
     relies heavily on masking this is very hard to fix.

Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1  action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2  action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3  action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND         Q:00           ctrl:00000080 prop:00000210
01: FPR  == 00000210 AND CLE     Q:00           ctrl:00000281 prop:00000210
02: MASK == ffffffff AND         Q:00           ctrl:00000080 prop:ffffffff
03: DPT  == 00000003 AND         Q:00           ctrl:0000008e prop:00000003
04: DIA  == 0a000003             Q:11           ctrl:0000440c prop:0a000003
05: DPT  == 00000002 AND         Q:00           ctrl:0000008e prop:00000002
06: DIA  == 0a000002             Q:09           ctrl:0000240c prop:0a000002
07: DIA  == 0a000001 AND         Q:00           ctrl:0000008c prop:0a000001
08: DPT  == 00000001     CLE     Q:01           ctrl:0000060e prop:00000001
ff: MASK >= 00000000             Q:00           ctrl:00000020 prop:00000000

Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules.  We found no errata covering this.

The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: NAleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAX_FILER_IDX is the last usable index.  Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.

We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.

Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.

This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were missing curly braces so it means we call add_debugfs_mem()
unintentionally.

Fixes: 3ccc6cf7 ('cxgb4: Adds support for T6 adapter')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit "e29aa339 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.

Fixes: e29aa339 ("bna: Enable Multi Buffer RX")
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NRasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PP2 controller is capable of per-CPU TX processing, which means there are
per-CPU banked register sets and queues. Current version of the driver supports
TX packet coalescing - once on given CPU sent packets amount reaches a threshold
value, an IRQ occurs. However, there is a single interrupt line responsible for
CPU0/1 TX and RX events (the latter is not per-CPU, the hardware does not
support RSS).

When the top-half executes the interrupt cause is not known. This is why in
NAPI poll function, along with RX processing, IRQ cause register on both
CPU's is accessed in order to determine on which of them the TX coalescing
threshold might have been reached. Thus the egress processing and releasing the
buffers is able to take place on the corresponding CPU. Hitherto approach lead
to an illegal usage of on_each_cpu function in softirq context.

The problem is solved by resigning from TX coalescing interrupts and separating
egress finalization from NAPI processing. For that purpose a method of using
hrtimer is introduced. In main transmit function (mvpp2_tx) buffers are released
once a software coalescing threshold is reached. In case not all the data is
processed a timer is set on this CPU - in its interrupt context a tasklet is
scheduled in which all queues are processed. At once only one timer per-CPU can
be running, which is controlled by a dedicated flag.

This commit removes TX processing from NAPI polling function, disables hardware
coalescing and enables hrtimer with tasklet, using new per-CPU port structure
(mvpp2_port_pcpu).
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mvpp2 driver allows usage of per-CPU TX processing. Once the packets are
prepared independetly on each CPU, the hardware enqueues the descriptors in
common TX queue. After they are sent, the buffers and associated sk_buffs
should be released on the corresponding CPU.

This is why a special index is maintained in order to point to the right data to
be released after transmission takes place. Each per-CPU TX queue comprise an
array of sent sk_buffs, freed in mvpp2_txq_bufs_free function. However, the
index was used there also for obtaining a descriptor (and therefore a buffer to
be DMA-unmapped) from common TX queue, which was wrong, because it was not
referring to the current CPU.

This commit enables proper unmapping of sent data buffers by indexing them in
per-CPU queues using a dedicated array for keeping their physical addresses.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using spinlocks protection during one-time driver initialization is not
necessary. Moreover it resulted in invalid GFP_KERNEL allocation under the lock.

This commit removes redundant spinlocks from buffer manager part of mvpp2
initialization.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reported-by: NAlexandre Fournier <alexandre.fournier@wisp-e.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

failed to configure the page size for architectures with page size
different than 4K.

Fixes: 938fe83c ("net/mlx5_core: New device capabilities handling")
Signed-off-by: NCarol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are paths in the driver such as an unrecoverable error (UE) detection
followed by a driver unload wherein be_clear() is invoked twice.
Individual data structures are reset so that they are not cleaned/freed
twice. This patch does the same for eqo->affinity_mask. It is freed only
if EQs haven't yet been destroyed. This fixes a possible crash when
affinity_mask is freed twice.
Signed-off-by: NKalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An RX stall issue was seen on Lancer adapters, when RXQs are destroyed
while they are in an "out of buffer" state. This patch fixes this issue
by posting 64 buffers to each RXQ before destroying them in the close path.
This is done after ensuring that no more new packets are selected for
transfer to the RXQs by disabling interface filters.
Signed-off-by: NKalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW issues were observed on Lancer adapters if IFACE filters
(flags, mac addrs etc) are enabled *before* creating RXQs.  This patch
changes the driver design by enabling filters in be_open() --
instead of be_setup() -- after RXQs are created and buffers posted.
Two new wrapper functions, be_enable_if_filters() and
be_disable_if_filters() are introduced to enable/disable IFACE filters in
be_open()/be_close() respectively. In be_setup() the IFACE is now created
only with the RSS flag.
Signed-off-by: NKalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: NSathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch b1c17215: "stmmac: add ipq806x glue layer", leads to the
following static checker warning:

.../stmmac/dwmac-ipq806x.c:314 ipq806x_gmac_probe()
warn: double left shift '1 << (1 << gmac->id)'

The NSS_COMMON_CLK_SRC_CTRL_OFFSET macro is used once as an offset, and
once as a mask, which is a bug indeed. We'll fix it by defining the
offset as the real offset value and computing the mask from it when
required.

Tested on IPQ806x ref designs AP148 & DB149.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to this patch, rx buffer size for each rx queue
of an interface is configurable through dts bindings.
But for an interface, the first rx queue's rx buffer
size is always the usual MTU size (plus usual overhead)
and page size for the remaining rx queues (if they are
enabled by specifying a non-zero rx queue depth dts
binding of the corresponding interface).  This patch
removes the rx buffer size configuration capability.
Signed-off-by: NWingMan Kwok <w-kwok2@ti.com>
Acked-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As well as for kernels built only for ThunderX ARCH_THUNDERX is also enabled
for kernels which support multiple platforms (such as distro kernels). Thus
"default ARCH_THUNDER" is inappropriate.

I believe default m is equally frowned upon, so remove the line completely
rather than "default m if ARCH_THUNDER".
Signed-off-by: NIan Campbell <ijc@hellion.org.uk>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: Derek Chickles <derek.chickles@caviumnetworks.com>
Cc: Satanand Burla <satananda.burla@caviumnetworks.com>
Cc: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Cc: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enforcing this flag in RxConfig for the mentioned chips fixes netdev
watchdog issues prepended with AMD IOMMU message(s) like:
AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x001d address=0x0000000000003000 flags=0x0050]

Note that this flag is also set in Realtek's own driver for these chips.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Tested-by: NAlexander Lindqvist <alexander@bitspace.se>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.

Fix this by initializing the refcount to be coherent with the initial
device status.

Fixes:
8fff755e (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vortex_up is failed, the skb buffers allocated by __netdev_alloc_skb
in vortex_open are not released, which may cause resource leaks.
This bug has been submitted before.
This patch modifies the error handling code to fix it.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing a port's netdevice in 'rocker_remove_ports', we should
also free the allocated 'net_device' structure. Do that by calling
'free_netdev' after unregistering it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Fixes: 4b8ac966 ("rocker: introduce rocker switch driver")
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 50649ab1 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab1 back.

This fixes the following errors when used as a module:
  stmmac_platform: module license 'unspecified' taints kernel.
  Disabling lock debugging due to kernel taint
  stmmac_platform: Unknown symbol devm_kmalloc (err 0)
  stmmac_platform: Unknown symbol stmmac_suspend (err 0)
  stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
  stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
  stmmac_platform: Unknown symbol platform_get_resource (err 0)
  stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
  stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
  stmmac_platform: Unknown symbol of_alias_get_id (err 0)
  stmmac_platform: Unknown symbol stmmac_resume (err 0)
  stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)

Fixes: 50649ab1 ("stmmac: drop driver from stmmac platform code")
Reported-by: NIgor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.

The bflock is obviously obsoleted, its utility has been corroded
over time.  The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines.  The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device.  With these changes, the TX processing is stopped before
gfar_halt().

Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume.  Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.

Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)

Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC      drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
 static void lock_tx_qs(struct gfar_private *priv)
             ^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
 static void unlock_tx_qs(struct gfar_private *priv)
             ^
Reported-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use proper typecasting while performing byte-by-byte copy
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cortina phy does not have kernel driver and we don't attach
device with phy layer for intefaces like XFI, XLAUI etc,
Hence check for interface type before calling disconnect.
Signed-off-by: NThanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a crash when changing rss with multiple traffic flows.

While interface teardown, disable tx queues after all NAPI threads
are done. If done otherwise tx queues might be woken up inside NAPI
if any CQE_TX are processed.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a txq (SQ) remains in stopped state after this timeout its
considered as stuck and interface is reinited.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously TXQ is wakedup whenever napi is executed
and irrespective of if any CQE_TX are processed or not.
Added 'txq_stop' and 'txq_wake' counters to aid in debugging
if there are any future issues.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suppressing standard alloc_pages() warnings. Some kernel configs limit
alloc size and the network driver may fail. Do not drop a kernel
warning in this case, instead just drop a oneliner that the network
driver could not be loaded since the buffer could not be allocated.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixing TSO packages not being counted.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix for memory leak when changing queue/channel count via ethtool
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With earlier configured value sufficient number of CQEs are not
being reserved for transmitted packets. Hence under heavy incoming
traffic load, receive notifications will take away most of the CQ
thus transmit notifications will be lost resulting in tx skbs not
being freed.

Finally SQ will be full and it will be stopped, watchdog timer
will kick in. After this fix receive notifications will not take
morethan half of CQ reserving the rest for transmit notifications.

Also changed CQ & SQ sizes from 16k to 4k.
This is also due to the receive notifications taking first half of
CQ under heavy load and time taken by NAPI to clear transmit notifications
will increase with higher queue sizes. Again results in SQ being stopped.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NAleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>