Call igb_setup_link() when the PHY is powered up.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Reported-by: NJeff Westfahl <jeff.westfahl@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return a 0 directly rather than a constant.
Reported-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the defaults on probe for the packet buffer size registers for the
i210.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove cases where useless bare return is left at end of function.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes issue found by updated coccicheck.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:AVOID_EXTERNS found by checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes implementation to remove use of DEFINE_PCI_DEVICE_TABLE.
This patch fixes WARNING:DEFINE_PCI_DEVICE_TABLE
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes ERROR:INITIALISED_STATIC from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:MSLEEP found by checkpatch check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:LONG_LINE found with checkpatch check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes ERROR:RETURN_PARENTHESES from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:MISSING_BREAK found with checkpatch check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes ERROR:ASSIGN_IN_IF found with checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:NETWORKING_BLOCK_COMMENT_STYLE from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:LEADING_SPACE, WARNING:SPACING, ERROR:SPACING,
WARNING:SPACE_BEFORE_TAB and ERROR_CODE_INDENT from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:BRACES and ERROR:OPEN_BRACE from
checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:PREFER_PR_LEVEL and WARNING:SPLIT_STRING
from checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RQDPC on i210/i211 is R/W not ReadClear. Clear after reading.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

last_rx_timestamp should be updated only when rx time stamp is
read. Also it's only used with NICs that have per-interface time
stamping resources so it can be moved to adapter structure and
set in igb_ptp_rx_rgtstamp().
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)

@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.

Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Prior to cd14ef54 (igb: Change to use statically allocated array for
MSIx entries), having msix_entries different from NULL was an indicator
that MSIX is enabled.
In igb_set_interrupt_capabiliy we may fall back to MSI-only. Prior to
the above patch msix_entries was set to NULL by
igb_reset_interrupt_capability.

However, now we are checking the flag for IGB_FLAG_HAS_MSIX and so the
stack gets completly confused:

[   42.659791] ------------[ cut here ]------------
[   42.715032] WARNING: CPU: 7 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x15c/0x1fb()
[   42.848263] NETDEV WATCHDOG: eth0 (igb): transmit queue 0 timed out
[   42.923253] Modules linked in:
[   42.959875] CPU: 7 PID: 0 Comm: swapper/7 Not tainted 3.14.0-rc2-mptcp #437
[   43.043184] Hardware name: HP ProLiant DL165 G7, BIOS O37 01/26/2011
[   43.119215]  0000000000000108 ffff88023fdc3da8 ffffffff81487847 0000000000000108
[   43.208165]  ffff88023fdc3df8 ffff88023fdc3de8 ffffffff81034e7d ffff88023fdc3dd8
[   43.297120]  ffffffff813fff10 ffff880236018000 ffff880236b178c0 0000000000000008
[   43.386071] Call Trace:
[   43.415303]  <IRQ>  [<ffffffff81487847>] dump_stack+0x49/0x62
[   43.484174]  [<ffffffff81034e7d>] warn_slowpath_common+0x77/0x91
[   43.556049]  [<ffffffff813fff10>] ? dev_watchdog+0x15c/0x1fb
[   43.623759]  [<ffffffff81034f2b>] warn_slowpath_fmt+0x41/0x43
[   43.692511]  [<ffffffff813fff10>] dev_watchdog+0x15c/0x1fb
[   43.758141]  [<ffffffff813ffdb4>] ? __netdev_watchdog_up+0x64/0x64
[   43.832091]  [<ffffffff8103cd04>] call_timer_fn+0x17/0x6f
[   43.896682]  [<ffffffff8103cebe>] run_timer_softirq+0x162/0x1a2
[   43.967511]  [<ffffffff81038520>] __do_softirq+0xcd/0x1cc
[   44.032104]  [<ffffffff81038689>] irq_exit+0x3a/0x48
[   44.091492]  [<ffffffff81026d43>] smp_apic_timer_interrupt+0x43/0x50
[   44.167525]  [<ffffffff8148c24a>] apic_timer_interrupt+0x6a/0x70
[   44.239392]  <EOI>  [<ffffffff8100992c>] ? default_idle+0x6/0x8
[   44.310343]  [<ffffffff81009b31>] arch_cpu_idle+0x13/0x18
[   44.374934]  [<ffffffff81066126>] cpu_startup_entry+0xa7/0x101
[   44.444724]  [<ffffffff81025660>] start_secondary+0x1b2/0x1b7
[   44.513472] ---[ end trace a5a075fd4e7f854f ]---
[   44.568753] igb 0000:04:00.0 eth0: Reset adapter
[   46.206945] random: nonblocking pool is initialized
[   46.465670] irq 44: nobody cared (try booting with the "irqpoll" option)
[   46.545862] CPU: 7 PID: 0 Comm: swapper/7 Tainted: G        W    3.14.0-rc2-mptcp #437
[   46.640610] Hardware name: HP ProLiant DL165 G7, BIOS O37 01/26/2011
[   46.716641]  ffff8802363f8c84 ffff88023fdc3e38 ffffffff81487847 00000000a03cdb6d
[   46.805598]  ffff8802363f8c00 ffff88023fdc3e68 ffffffff81068489 0000007f81825400
[   46.894539]  ffff8802363f8c00 0000000000000000 0000000000000000 ffff88023fdc3ea8
[   46.983484] Call Trace:
[   47.012714]  <IRQ>  [<ffffffff81487847>] dump_stack+0x49/0x62
[   47.081585]  [<ffffffff81068489>] __report_bad_irq+0x35/0xc1
[   47.149295]  [<ffffffff81068683>] note_interrupt+0x16e/0x1ea
[   47.217006]  [<ffffffff8106679e>] handle_irq_event_percpu+0x116/0x12e
[   47.294075]  [<ffffffff810667e9>] handle_irq_event+0x33/0x4f
[   47.361787]  [<ffffffff81068c95>] handle_fasteoi_irq+0x83/0xd1
[   47.431577]  [<ffffffff81003d5b>] handle_irq+0x1f/0x28
[   47.493047]  [<ffffffff81003567>] do_IRQ+0x4e/0xd4
[   47.550358]  [<ffffffff8148b06a>] common_interrupt+0x6a/0x6a
[   47.618066]  <EOI>  [<ffffffff8100992c>] ? default_idle+0x6/0x8
[   47.689016]  [<ffffffff81009b31>] arch_cpu_idle+0x13/0x18
[   47.753605]  [<ffffffff81066126>] cpu_startup_entry+0xa7/0x101
[   47.823397]  [<ffffffff81025660>] start_secondary+0x1b2/0x1b7
[   47.892146] handlers:
[   47.919301] [<ffffffff812fbd7d>] igb_intr

So, this patch unsets the flag to indicate that we are not using MSIX.
This patch does exactly this: Unsetting the flag when falling back to MSI.

Fixes: cd14ef54 (igb: Change to use statically allocated array for MSIx entries)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NChristoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When igb_set_interrupt_capability() calls
igb_reset_interrupt_capability() (e.g., because CONFIG_PCI_MSI is unset),
num_q_vectors has been set but no vector has yet been allocated.

igb_reset_interrupt_capability() will then call igb_reset_q_vector,
which assumes that the vector is allocated. As this is not the case, we
are accessing a NULL-pointer.

This patch fixes it by checking that q_vector is indeed different from
NULL.

Fixes: 02ef6e1d (igb: Fix queue allocation method to accommodate changing during runtime)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NChristoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add initial register rd/wr for surprise removal (LER).
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively. Previously a process had to be privileged and could
only set values, it couldn't return what is currently set without
possibly overwriting the value.

This patch adds support for this new operation into igb by keeping a
shadow copy of the config in the adapter structure, which is returned
upon request.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For i350 VLAN stripping for VMs is not enabled in the VMOLR register but in
the DVMOLR register. Making the changes accordingly. It's not necessary to
unset the E1000_VMOLR_STRVLAN bit on i350 as the hardware will simply ignore
it.

Without this change if a VLAN is configured for a VF assigned to a guest
via (i.e.)
ip link set p1p1 vf 0 vlan 10
the VLAN tag will not be stripped from packets going into the VM. Which they
should be because the VM itself is not aware of the VLAN at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Command line parameters QueuePairs, Node, EEE, DMAC and InterruptThrottleRate
do not exist these days. Remove all references to them in the Documentation
folder and update code comments.
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the bh safe variant with the hard irq safe variant.

We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.

Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently added code comment was missing a space that is needed.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where using ethtool for EEE setting was not
working correctly.  This patch also fixes a problem where
the function that checks for EEE status on i354 devices was not being
called and was causing warnings with static analysis tools.
Reported-by: NRashika Kheria <rashika.kheria@gmail.com>
Reported-by: NJosh Triplett <josh@joshtriplett.org>
Reported-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: NTom Herbert <therbert@google.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the license text to remove address of Free Software
Foundation and refer  users to www.gnu.org instead. This patch also updates
the copyright dates in appropriate igb driver files.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes how the driver initializes MSIx and checks
for MSIx configuration.  This change makes it easier to reconfigure the
device when queue changes happen at runtime using ethtool's set_channels
feature.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When changing number of queues using ethtool's set_channels during runtime,
a queue allocation could fail, which can leave the device in a down state.
In order to preserve the usability of the device in this scenario, this patch
changes the driver to allocate the  number of queues only if they have not
been allocated already. The first allocation is then done for the max number
of queues, which is the default queues for this driver.   With this change,
queue quantity changes are not subject to queue allocation failures.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>