* Set the correct hwif->dma_base for the second channel in
  ide_get_or_set_dma_base().

* Remove DMA enable code from cs5520_set_pio_mode(), this can
  be handled by the generic ->dma_host_on method now.

* Add VDMA check to ide_config_drive_speed().

* drive->using_dma was never enabled since cs5520 host driver's
  ->ide_dma_on method overrided the generic ->ide_dma_on (so
  __ide_dma_on() was never called, drive->using_dma was never set
  and VDMA was never used since it depends on drive->using_dma).

  Fix it by using ->dma_host_on method instead of ->ide_dma_on
  (also add matching ->dma_host_off method).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE core guarantees that ->set_dma_mode will be called only
for DMA modes set in SWDMA/MWDMA/UDMA masks.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Program register 0x40 in sl82c105_resetproc().

* Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Program DMA timings in sl82c105_dma_start() (->dma_start method)
  before starting DMA transfer.

* Add sl82c105_dma_end() (->ide_dma_end method) to switch back to
  PIO timings when DMA transfer is complete.

* In sl82c105_set_pio_mode() program timings regardless of ->using_dma
  setting and in sl82c105_set_dma_mode() only cache the new timings.

* Remove no longer needed sl82c105_{ide_dma_on,off_quietly}().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

->ide_dma_on method is called only after successful ide_dma_check() call
(ide_dma_check()->ide_tune_dma() checks DMA blacklist) or if drive->using_dma
has been previously enabled for a given device (->ide_dma_on is the only place
which sets drive->using_dma to '1').

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* ->dma_off_quietly is always called before ide_set_dma()
  so the call can be moved inside ide_set_dma().

* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
  call for 'rc == -1' case is redundant, remove it.

* '0' and '-1' are the only values returned by ide_dma_check()
  so remove dead code for other cases.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_set_dma() calls ->ide_dma_on method itself and returns zero
only if ->ide_dma_on call succeeded.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on pata_sc1200.c.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
  what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().

* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
  (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
  serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
  methods in host drivers that don't (IDE core code guarantees that
  ->set_dma_mode will be called only for modes which are present
  in SWDMA/MWDMA/UDMA masks).

While at it:

* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
  hpt34x/hpt366/pdc202xx_old/serverworks host driver.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out UDMA programming code from sis_set_dma_mode() to per
  chipset family helpers: sis_{ata33,ata133}_program_udma_timings().

* Add sis_program_udma_timings() helper.

* Remove unneeded casts to 'unsigned long'.

* Minor cleanups.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move PIO programming code from pdcnew_set_mode() to pdcnew_set_pio_mode().

* Rename pdcnew_set_mode() to pdcnew_set_dma_mode().

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move the common code from ide_dump_{ata,atapi}_status() to
  ide_dump_status().

* ide_dump_{ata,atapi}_status() -> ide_dump_{ata,atapi}_error().

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Export ide_get_lba_addr().

* Convert idedisk_{read_native,set}_max_address() to use ide_get_lba_addr().

* Remove incorrect comment from idedisk_read_native_max_address()
  (noticed by Sergei).

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

power4:

drivers/ide/ide-lib.c: In function `ide_dump_sector':
drivers/ide/ide-lib.c:516: warning: long long unsigned int format, u64 arg (arg 2)

We don't know what type is used to implement u64 hence it must always be cast
when printed.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out code reading taskfile registers from ide_end_drive_cmd()
  to the new ide_tf_read() helper.

* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
  particular IDE taskfile register in ide_tf_read().

* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.

* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.

* Factor out code getting sector address from ide_dump_ata_status()
  to the new ide_dump_sector() function.

* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().

* Remove no longer needed ide_read_24().

The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix registers loading order in ide_dump_ata_status()/ide_read_24().

Load registers in this order:
* IDE_SECTOR_REG
* IDE_LCYL_REG
* IDE_HCYL_REG
* IDE_SELECT_REG

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_DMA_PIO_FALLBACK taskfile flag to indicate the need
  to skip loading taskfile registers in do_rw_taskfile().

* Export do_rw_taskfile().

* Convert __ide_do_rw_disk() to use do_rw_taskfile().

* Unexport ide_tf_load().

* Unexport {pre_task_out,task_in}_intr() and make it static.

* Remove incorrect comment about do_rw_taskfile() from <linux/ide.h>.

There should be no functionality changes caused by this patch.

v2:
* Add missing blk_fs_request() check to task_dma_ok() (for VDMA).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_tf_set_cmd() helper for selecting/setting command and data phase
  (note: DMA data phases are there for completness, they are not required ATM).

* Set IDE_TFLAG_WRITE taskfile flag for write requests in __ide_do_rw_disk().

* Convert __ide_do_rw_disk() to use the new ide_tf_set_cmd() helper.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

s/WAIT_CMD/WAIT_WORSTCASE/ to make the timeout the same as in do_rw_taskfile()
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_CUSTOM_HANDLER taskfile flag and use it for internal requests
  which require custom handlers.  Check the flag in do_rw_taskfile() and set
  handler accordingly.

* Cleanup ide_init_{specify,restore,setmult}_cmd() and rename it to
  ide_tf_set_{specify,restore,setmult}_cmd().

* Make {set_geometry,recal,set_multmode}_intr() static.

* Remove no longer needed 'handler' field from ide_task_t.

v2:
* 'handler' in do_rw_taskfile() must be set to NULL initially.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->data_phase to set ->handler in do_rw_taskfile() instead of
  setting ->handler in callers of ide_raw_taskfile()/do_rw_taskfile().

* Unexport task_no_data_intr() and make it static.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use task->data_phase in do_rw_taskfile() to decide what to do.

* task->prehandler is only used by TASKFILE[_MULTI]_OUT so just
  use pre_task_out_intr() directly and remove no longer needed
  'prehandler' field from ide_task_t.

* Remove no longer needed ide_pre_handler_t type.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

task->data_phase == TASKFILE_MULTI_{IN,OUT} vs drive->mult_count == 0
check is needed also for ide_taskfile_ioctl() requests that don't have
IDE_TFLAG_FLAGGED taskfile flag set.

Cc: Tejun Heo <htejun@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix __ide_do_rw_disk() to use ->OUTBSYNC instead of ->OUTB
(needed for pmac and scc_pata host drivers).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Save PCI regs values for both IDE ports in one buffer, in order to eliminate
a needless and ugly loop across all hwifs, searching for our PCI device.

Partially based on the previous patch by Jeff Garzik.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_IN_DATA taskfile flag to indicate the need of reading
  IDE_DATA_REG in ide_end_drive_cmd().

  Set the new flag in ide_taskfile_ioctl() if ->in_flags.b.data is set.

* Add IDE_TFLAG_FLAGGED_SET_IN_FLAGS taskfile flag to indicate the
  need of modifying ->in_flags in ide_taskfile_ioctl().

  Set the new flag in flagged_taskfile() and move the code modifying
  ->tf_in_flags to ide_taskfile_ioctl().

  While at it remove the bogus comment: ->tf_in_flags (except .b.data)
  have no effect on selection of registers to read.

* Remove no longer needed 'tf_in_flags' field from ide_task_t.

As the result we finally have the internals of HDIO_DRIVE_TASKFILE ioctl
separated from the core IDE code.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'data_buf' and 'nsect' variables in ide_taskfile_ioctl()
  to cache data buffer pointer and number of sectors to transfer
  (this allows us to have only one ide_diag_taskfile() call).

* Add IDE_TFLAG_WRITE taskfile flag and use it to check whether
  the REQ_RW request flag should be set.

* Move ->command_type handling from ide_diag_taskfile() to
  ide_taskfile_ioctl() and use ->req_cmd instead of ->command_type.

* Add 'nsect' parameter to ide_raw_taskfile().

* Merge ide_diag_taskfile() into ide_raw_taskfile().

* Initialize ->data_phase explicitly in idedisk_prepare_flush(),
  ide_start_power_step() and ide_disk_special().

* Remove no longer needed 'command_type' field from ide_task_t.

* Add #ifndef/#endif __KERNEL__ to <linux/hdreg.h> around no
  longer used by kernel IDE_DRIVE_TASK_* and TASKFILE_* defines.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Given that:

* hpt366.c::hpt3xx_intrproc() is the only user of hwif->intrproc

* hpt366.c::hpt3xx_quirkproc() sets drive->quirk_list to 1 for quirky drives
  which is a value unique to hpt366 host driver

we can remove hwif->intproc and just check for drive->quirk_list == 1
in ide_do_request().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_pktcmd_tf_load() helper and convert ATAPI device drivers to use it.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Load IDE_BCOUNTL_REG before IDE_BCOUNTH_REG when issuing packet command.

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Load IDE_CONTROL_REG before other registers in cdrom_start_packet_command().

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).

While at it move misplaced FIXME comment in the right place.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove atapi_ireason_t.

While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)

v2:
* v1 had CD and IO bits reversed in many places.

* Use CD and IO defines from <linux/hdreg.h>.

v3:
* Fix incorrect "(ireason & IO) == test_bit()". (Noticed by Sergei)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ata_nsector_t, ata_data_t (unused) and atapi_bcount_t.

While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove atapi_feature_t.

While at it:
* replace 'HWIF(drive)' by 'hwif'
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove atapi_error_t.

While at it:
* replace 'HWIF(drive)' by 'drive->hwif'

v2:
* Add {ILI,EOM,LFS}_ERR defines to <linux/hdreg.h>.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ata_status_t (unused) and atapi_status_t.

While at it:
* replace 'HWIF(drive)' by 'drive->hwif' (or just 'hwif' where possible)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>