Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 23 3月, 2012 2 次提交
  3. 19 3月, 2012 1 次提交
    • A
      hwmon: convert drivers/hwmon/* to use module_i2c_driver() · f0967eea
      由 Axel Lin 提交于 
      This patch converts the drivers in drivers/hwmon/* to use the
module_i2c_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
Cc: David George <david.george@ska.ac.za>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
      f0967eea
  5. 17 1月, 2012 1 次提交
  7. 06 1月, 2012 1 次提交
  9. 04 11月, 2011 2 次提交
    • J
      hwmon: (lm90) Make code more readable · b2589ab0
      由 Jean Delvare 提交于 
      Clean up the code to make it more readable:
* Remove reg_ and new_ prefixes from variable names, they made the
  names longer, causing extra line breaks, while not adding much
  value.
* Introduce struct device dev* = &client->dev in two functions, to
  avoid repeating client->dev everywhere in these functions.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
      b2589ab0
    • J
      hwmon: (lm90) Fix warnings · 8dc089d6
      由 Jean Delvare 提交于 
      With some configuration option combinations, we get the following
warnings:

drivers/hwmon/lm90.c: In function 'lm90_detect':
drivers/hwmon/lm90.c:1114: warning: 'chip_id' may be used uninitialized
in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_config1' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_convrate' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_emerg2' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_status2' may be used
uninitialized in this function

We can solve these easily by reading the register values first and
checking for errors later. These errors should be very rare, even in
the case of failed detection, so this change has no impact on
performance. And this makes checkpatch.pl happier.
Reported-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
      8dc089d6
  11. 29 7月, 2011 3 次提交
  13. 28 7月, 2011 1 次提交
  15. 29 4月, 2011 1 次提交
  17. 31 3月, 2011 1 次提交
  19. 29 10月, 2010 12 次提交
  21. 28 5月, 2010 1 次提交
  23. 06 3月, 2010 3 次提交
  25. 15 12月, 2009 3 次提交
  27. 10 12月, 2009 1 次提交
  29. 12 3月, 2009 1 次提交
  31. 27 10月, 2008 2 次提交
    • J
      hwmon: (lm90) Add support for the LM99 16 degree offset · 97ae60bb
      由 Jean Delvare 提交于 
      The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
      97ae60bb
    • J
      hwmon: (lm90) Fix handling of hysteresis value · ec38fa2b
      由 Jean Delvare 提交于 
      There are several problems in the way the hysteresis value is handled
by the lm90 driver:

* In show_temphyst(), specific handling of the MAX6646 is missing, so
  the hysteresis is reported incorrectly if the critical temperature
  is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
  the chip but data->temp_hyst isn't updated accordingly, so there is
  a short period of time (up to 2 seconds) where the old hystereris
  value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
  to compute the value of the hysteresis register lacks
  device-specific handling. As a result, the value of the hysteresis
  register might be incorrect for the ADT7461 and MAX6646 chips.

Fix these 3 bugs.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
      ec38fa2b
  33. 17 10月, 2008 4 次提交