Add the missing usb controller version info and port0, which is
required during setup usb phy.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Default CoreNet Coherency Bus (CCB) frequency on P3041 is 750MHz, but espi
cannot work at 40MHz with this CCB frequency, so we need to slow down the
clock rate of espi to 35MHz to make it work stable at the CCB frequency.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NTang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

In SGMII riser card different PHY chip are used with different external
IRQ from eTSEC. To support PHY link state auto detect in SGMII mode we
should add another group of PHY nodes for SGMII mode.

For MPC8572DS IRQ6 is used for PHY0~PHY1, IRQ7 is used for PHY2~PHY3.
For MPC8544DS and MPC8536DS IRQ6 is used for PHY0~PHY1.
For P2020DS IRQ5 is used for PHY1~PHY2.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJia Hongtao <B38951@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The board is really P1021RDB-PC, so rename from p1021rdb.* to p1021rdb-pc.*
Signed-off-by: NXu Jiucheng <Jiucheng.Xu@freescale.com>
Signed-off-by: NMatthew McClintock <msm@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add device tree nodes to enable ucc uart support on P1025RDB.
Signed-off-by: NZhicheng Fan <B32736@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

With 2-cell format interrupts of MSI PCIe ethernet card can not work.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJia Hongtao <B38951@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The issue log on core1 is:
root@mpc8572ds:~# ifconfig eth0 10.192.208.244
net eth0: could not attach to PHY
SIOCSIFFLAGS: No such device

To attach PHY node mdio@24520 should not be disabled in dts of core1.
Because all PHYs are controlled through this node as follows:

mdio@24520 {
	phy0: ethernet-phy@0 {
		interrupts = <10 1 0 0>;
		reg = <0x0>;
	};
	phy1: ethernet-phy@1 {
		interrupts = <10 1 0 0>;
		reg = <0x1>;
	};
	phy2: ethernet-phy@2 {
		interrupts = <10 1 0 0>;
		reg = <0x2>;
	};
	phy3: ethernet-phy@3 {
		interrupts = <10 1 0 0>;
		reg = <0x3>;
	};

	tbi0: tbi-phy@11 {
		reg = <0x11>;
		device_type = "tbi-phy";
	};
};
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJia Hongtao <B38951@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.

The BSC9131 SoC includes the following function and features:
    . Power Architecture subsystem including a e500 processor with 256-Kbyte
    shared L2 cache
    . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
    . The Multi Accelerator Platform Engine for Femto BaseStation Baseband
      Processing (MAPLE-B2F)
    . A multi-standard baseband algorithm accelerator for Channel
      Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
      UP/DL Channel processing, and CRC algorithms
    . Consists of accelerators for Convolution, Filtering, Turbo Encoding,
      Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
      Inversion operations
    . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
      with ECC, up to 400-MHz clock/800 MHz data rate
    . Dedicated security engine featuring trusted boot
    . DMA controller
    . OCNDMA with four bidirectional channels
    . Interfaces
    . Two triple-speed Gigabit Ethernet controllers featuring network
      acceleration including IEEE 1588. v2 hardware support and
      virtualization (eTSEC)
    . eTSEC 1 supports RGMII/RMII
    . eTSEC 2 supports RGMII
    . High-speed USB 2.0 host and device controller with ULPI interface
    . Enhanced secure digital (SD/MMC) host controller (eSDHC)
    . Antenna interface controller (AIC), supporting three industry standard
      JESD207/three custom ADI RF interfaces (two dual port and one single
      port) and three MAXIM's MaxPHY serial interfaces
    . ADI lanes support both full duplex FDD support and half duplex TDD
      support
    . Universal Subscriber Identity Module (USIM) interface that facilitates
      communication to SIM cards or Eurochip pre-paid phone cards
    . TDM with one TDM port
    . Two DUART, four eSPI, and two I2C controllers
    . Integrated Flash memory controller (IFC)
    . TDM with 256 channels
    . GPIO
    . Sixteen 32-bit timers

The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.

 BSC9131RDB Overview
 ----------------------
    BSC9131 SoC
    1Gbyte DDR3 (on board DDR)
    128Mbyte 2K page size NAND Flash
    256 Kbit M24256 I2C EEPROM
    128 Mbit SPI Flash memory
    USB-ULPI
    eTSEC1: Connected to RGMII PHY
    eTSEC2: Connected to RGMII PHY
    DUART interface: supports one UARTs up to 115200 bps for console display

 Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NAkhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NRajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This reverts commit 96cc017c.

The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.

To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node.  This node assumes that the localbus 'ranges'
property is sorted in chip-select order.  That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc.  This is how the 'ranges' property is
supposed to be arranged.

Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS.  Linux normally does not care, since it does not program the
localbus.  But the indirect-mode code on the P1022DS does care.

The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome.  The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.

Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses.  This code is simpler and more reliable, and it does not require
a U-boot or device tree change.

Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

NAND on p2041 uses CS1 as chip select.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This reference board dates back to 2004, and is largely a legacy
EOL product.  The MPC8560 is a pre e500v2 CPU.  The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.

Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.

Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJin Qing <b24347@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NTang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add EEPROM to the P1010RDB device tree.
The 24c01 acts as a memory SPD so it shouldn't be overwritten without
care.
The 24c256 is a general purpose memory.
Signed-off-by: NGustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This reverts commit 0c00f656.
The initial commit was my fault. There are two boards out there:
P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have
a RDB board in front of me while I the RDB-PC. This patch makes it work
for the RDB-PC variant and breaks it for the RDB. Now there is a device
tree file available for the RDB-PC which was not there earlier. So with
this revert, everything gets back to normal :)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add spi support for mgcoge into the platform code and the dts
file. Additionaly SPIDEV is switched on in the defconfig and the
updates for the newer kernel version are committed. The SPI
interface is used to drive the Maxim DS3106 clock chip.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the RTC support into the p1022ds device tree
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Commit 430b01e8 ("[POWERPC] Kill
flatdevtree.c") killed the two files including flatdevtree_env.h. It was
apparently just an oversight to not kill that header too. Kill it now.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently we build all board files regardless of the final zImage
target.  This is sub-optimal (in terms on compilation) and leads to
problems in one platform needlessly causing failures for other
platforms.

Use the Kconfig variables to selectively construct this board files to
build.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NMai La <mla@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The association in the decice tree between PCI and MSI
using fsl,msi property was an artificial one and it does
not reflect the actual hardware.
Signed-off-by: NDiana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit c55aef0e "powerpc/boot: Change the load address for the wrapper
to fit the kernel" adjusted the laod address if the uncompressed kernel
was too large.  Ps3 does not compress the kernel and uses a different
linker script, so do not adjust the load address in that case.

fixes this build error:

powerpc64-linux-ld: section .text loaded at [0000000000e00000,0000000000e0721b] overlaps section .kernel:dtb loaded at [0000000000e00000,0000000000e0066f]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add DTS file for a4m072 board and add its name to the list
of the supported boards.
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Grant Likely <grant.likely@secretlab.ca>
cc: devicetree-discuss@ozlabs.org
cc: Wolfgang Denk <wd@denx.de>
cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

This patch updates the dts file for bluestone board with support:
- UART1
- L2 cache
- NAND with NDFC
- PCI-E
Signed-off-by: NVinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The MSIIR register for each MSI bank is aliased to a different
address. The MSI node reg property was updated to contain this
address:

e.g. reg = <0x41600 0x200 0x44140 4>;

The first region contains the address and length of the MSI
register set and the second region contains the address of
the aliased MSIIR register at 0x44140.
Signed-off-by: NDiana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Create mpc8548cds_36b.dts. Support 36-bit mode.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Create mpc8548cds.dtsi
* Move lbc, soc and pci0 nodes to mpc8548cds_32b.dtsi
* Change cuImage.mpc8548cds to cuImage.mpc8548cds_32b
* Rename mpc8548cds.dts to mpc8548cds_32b.dts
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Correct ethernet1 and add ethernet2 and ethernet3.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix the compatible string of sec 4.0 to match with CAAM driver according
to Documentation/devicetree/bindings/crypto/fsl-sec4.txt
Signed-off-by: NLiu Shuo <shuo.liu@freescale.com>
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The mpc836x_mds platform has been broken since the commit
6fe32649

  "netdev/phy: Use mdiobus_read() so that proper locks are taken"

which caused the fsl_pq_mdio TBI autoprobe to oops.  The oops
was "fixed" in commit 28d8ea2d

  "fsl_pq_mdio: Clean up tbi address configuration"

by simply removing the the autoscan code, and making tbi nodes
mandatory.  Some of the newer reference platforms were updated
to have tbi nodes in 22066949

  "powerpc: Add TBI PHY node to first MDIO bus"

but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:

 fsl-pq_mdio: probe of e0102120.mdio failed with error -16
   ...
 net eth0: Could not attach to PHY
 eth0: Cannot initialize PHY, aborting.

Add a TBI node and use the 1st free address for it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>