Currently hisi_sas_device.device_id is a u64. This can create a problem
in selecting the queue for a device, in that this code does a 64b
division on device id. For some 32b systems, 64b division is slow and
the lib reference must be explicitly included.

The device id does not need to be 64b in size, so, as a solution, just
make as an int.

Also, struct hisi_sas_device elements are re-ordered to improve packing
efficiency.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch is a workaround for a SoC bug where an internal abort command
may timeout. In v2 hw, the channel should become idle in order to finish
abort process. If the target side has been sending HOLD, host side
channel failed to complete the frame to send, and can not enter the idle
state. Then internal abort command will timeout.

As this issue is only in v2 hw, we deal with it in the hw layer.  Our
workaround solution is: If abort is not finished within a certain period
of time, we will check HOLD status. If HOLD has been sending, we will
send break command.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch provides a workaround a SoC bug where SATA IPTTs for
different devices may conflict.

The workaround solution requests the following:
1. SATA device id must be even and not equal to SAS IPTT.
2. SATA device can not share the same IPTT with other SAS or
   SATA device.

Besides we shall consider IPTT value 0 is reserved for another SoC bug
(STP device open link at firstly after SAS controller reset).

To sum up, the solution is: Each SATA device uses independent and
continuous 32 even IPTT from 64 to 4094, then v2 hw can only support 63
SATA devices.  All SAS device(SSP/SMP devices) share odd IPTT value from
1 to 4095.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After resetting the controller, the process of scanning SATA disks
attached to an expander may fail occasionally. The issue is that the
controller can't close the STP link created by target if the max link
time is 0.

To workaround this issue, we reject STP link after resetting the
controller, and change the corresponding PHY to accept STP link only
after receiving data.

We do this check in cq interrupt handler. In order not to reduce
efficiency, we use an variable to control whether we should check and
change PHY to accept STP link.

The function phys_reject_stp_links_v2_hw() should be called after
resetting the controller.

The solution of another SoC bug "SATA IO timeout", that also uses the
same register to control STP link, is not effective before the PHY
accepts STP link.
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.

Regardless, it is not right to release this early.

This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().

It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.

The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.

This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NXiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently the all the slot processing for the completion queue is done
in ISR context. It is judged that the slot processing can take a long
time, especially when a SATA NCQ completes (upto 32 slots).

So, as a solution, defer the bulk of the ISR processing to tasklet
context. Each CQ will have its down tasklet.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NXiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: NHanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add the function to set PHY min and max linkrate through
sysfs interface.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Sometimes the value of hisi_sas_device.running_req
would go negative unless we have the check for
running_req >= 0 before trying to decrement.

This is because using running_req is not thread-safe.

As such, the value for running_req may be actually incorrect,
so use atomic64_t instead.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NXiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently slots are allocated from queues in a round-robin fashion.
This causes a problem for internal commands in device mode. For this
mode, we should ensure that the internal abort command is the last
command seen in the host for that device. We can only ensure this when
we place the internal abort command after the preceding commands for
device that in the same queue, as there is no order in which the host
will select a queue to execute the next command.

This queue restriction makes supporting scsi mq more tricky in
the future, but should not be a blocker.

Note: Even though v1 hw does not support internal abort, the
      allocation method is chosen to be the same for consistency.
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The hip06 D03 and hip07 D05 boards have different reference clock
frequencies for the SAS controller.

Register PHY_CTRL needs to be programmed differently according to this
frequency, so add support for this.

The default register setting in PHY_CTRL is for 50MHz, so only update
this register when the refclk frequency is 66MHz.

For ACPI we expect the _RST handler to set the correct value for
PHY_CTRL (we're forced to take different approach for DT and ACPI as
ACPI does not support fixed-clock device).
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NXiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Optimise by saving an avoidable read in the get_free_slot function.  The
delivery queue write pointer will only be updated by software, so don't
bother re-reading what was already written in the previous call to
start_delivery function.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Optimise by saving an avoidable read in the cq interrupt.  The queue
read pointer will only be updated by software, so don't bother
re-reading what was already written in the previous interrupt.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add main code for internal abort functionality.

The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.

Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.

Two modes of internal abort are supported:

 - device
 - individual command

For device, when the internal abort is issued all commands in the host
for that device are aborted.  For a single command, only that command is
aborted if it is still in the host.

In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add methods to use HW specific versions of functions to allocate slot
and device.  HW specific methods are permitted to workaround device id
vs IPTT collision issue in v2 hw.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.

Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.

Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Acked-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add a function to abort a slot (task) in the target
device and then cleanup and complete the task.
The function is called from work queue context as
it cannot be called from the context where it is
triggered (interrupt).
Flag hisi_sas_slot.abort is added as the flag used
in the slot error handler to indicate whether the
slot needs to be aborted in the sdev prior to
cleanup and finish.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The hisi_sas driver is required to support both device tree and
ACPI. The scanning of the device properties now uses the Unified Device
Properties API, which serves both OF and ACPI.

Since syscon is not supported by ACPI, syscon is only used in the driver
when device tree is used.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since hisi_sas_itct format is different between v1 and v2 hw, give more
general names for some fields.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since the error record structure is different for v2 hw, make
hisi_sas_err_record opaque and add hisi_sas_err_record_v1.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since v2 hw only supports 2048 itct entries, as opposed to 4096 for v1
hw, set the max itct entries to the lower of the two.

It is not anticipated that any device with v1 will ever require to
connect > 2048 devices.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since v2 hardware permits different numbers of commands to v1, set this
as configurable in hisi_sas_hw.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Relocate DEV_IS_EXPANDER to hisi_sas.h as it will be required for v2 hw
support.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It is preferred that drivers use platform_get_irq() instead of
irq_of_parse_and_map(), so replace.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Originally the driver would use of_irq_count to calculate how much
memory is required for storing the interrupt names, since the number of
interrupt sources for the controller is variable.  Since of_irq_count
cannot be used by the driver, use fixed names.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add method for lldd_control_phy. Currently link rate control and spinup
hold is unsupported.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add functions for scsi host template scan_finished and scan_start
methods.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add support for smp function, which allows devices attached by expander
to be controlled.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add abnormal irq handler. This handler is concerned with phy down event.
Also add port formed and port deformed handlers.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add functions to deal with lldd_dev_found and lldd_dev_gone.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add cq interrupt handler and also slot error handler function.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>