* Move hooks for port/host specific methods from ide_hwif_t to
  'struct ide_port_ops'.

* Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info'
  and ide_hwif_t.

* Update host drivers and core code accordingly.

While at it:

* Rename ata66_*() cable detect functions to *_cable_detect() to match
  the standard naming. (Suggested by Sergei Shtylyov)

v2:
* Fix build for bast-ide. (Noticed by Andrew Morton)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

"bootable" should be the default behavior so replace
IDE_HFLAG_BOOTABLE host flag with IDE_HFLAG_NON_BOOTABLE.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

->busproc method is used by HDIO_SET_BUSSTATE ioctl but it has no chance
of working as intended (in 2.4.x days) because to issue an ioctl there
is a device node needed and:

- for BUSSTATE_TRISTATE+OFF it is too late (devices are already gone)

- for BUSSTATE_TRISTATE+ON it is too early (devices are not registered yet)

Just remove ->busproc method for now (it was only implemented by hpt366,
siimage and tc86c001 host drivers).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix kernel oops due to machine check occuring in init_chipset_siimage() on PPC
44x platforms.  These 32-bit CPUs have 36-bit physical address and PCI I/O and
memory spaces are mapped beyond 4 GB; arch/ppc/ code has a fixup in ioremap()
that creates an illusion of the PCI I/O and memory resources being mapped below
4 GB, while arch/powerpc/ code got rid of this fixup with PPC 44x having instead
CONFIG_RESOURCES_64BIT=y -- this causes the resources to be truncated to 32-bit
'unsigned long' type in this driver, and so non-existant memory being ioremap'ed
and then accessed...

Thanks to Valentine Barshak for providing an initial patch and explanations.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove write-only ->sata_misc[] from ide_hwif_t.

* Remove no longer used SATA_{MISC,PHY,IEN}_OFFSET defines.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
  SATA_{ERROR,STATUS}_REG macros.

* Remove no longer needed SATA_*_REG macros.

While at it:

* Remove needless SATA Status register read from sil_sata_reset_poll().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->cable_detect method to ide_hwif_t.

* Call the new method in ide_init_port() if:
  - the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
  - DMA initialization was successful (if hwif->dma_base is not set
    ide_init_port() sets hwif->ultra_mask to zero)
  - "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')

* Convert PCI host drivers to use ->cable_detect method.

While at it:

* Factor out cable detection to separate functions (if not already done).

* hpt366.c/it8213.c/slc90e66.c:
  - don't check cable type if "idex=ata66" is used

* pdc202xx_new.c:
  - add __devinit tag to pdcnew_cable_detect()

* pdc202xx_old.c:
  - rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
  - add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Delete filenames/versions from comments.

I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.

While at it:

* Remove unused VERSION define from ide.c.

* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.

While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Assign drive->quirk_list in ->quirkproc implementations:
  - hpt366.c::hpt3xx_quirkproc()
  - pdc202xx_new.c::pdcnew_quirkproc()
  - pdc202xx_old.c::pdc202xx_quirkproc()

* Make ->quirkproc void.

* Move calling ->quirkproc from do_identify() to probe_hwif().

* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.

* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
  no longer needed drive->present check from is_dev_seagate_sata().

* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
  as an argument.  Then convert ide_register_hw() to accept 'quirkproc'
  argument instead of 'fixup' one.

* Remove no longer needed ->fixup method.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
  what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().

* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
  (aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
  serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
  methods in host drivers that don't (IDE core code guarantees that
  ->set_dma_mode will be called only for modes which are present
  in SWDMA/MWDMA/UDMA masks).

While at it:

* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
  hpt34x/hpt366/pdc202xx_old/serverworks host driver.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename struct ide_pci_device_s to struct ide_port_info.

* Remove ide_pci_device_t typedef.

While at it:

* Fix __ide_pci_register_driver() comment.

* Fix aec62xx_init_one() comment.

* Remove unused 'cds' field from ide_hwgroup_t.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off sil_sata_udma_filter() from sil_udma_filter()
  and rename sil_udma_filter() to sil_pata_udma_filter().

* Rename siimage_busproc() to sil_sata_busproc().

* Rename siimage_reset_poll() to sil_sata_reset_poll()
  and in init_hwif_siimage() set ->reset_poll method only
  for SATA controllers.

* Rename siimage_pre_reset() to sil_sata_pre_reset(),
  in init_hwif_siimage() set ->pre_reset method only for
  SATA controllers and remove redundant is_sata() call.

* Add CONFIG_BLK_DEV_IDE_SATA #ifdef/#endif to pdev_is_sata()
  so compiler will know to throw out unused SATA code for
  CONFIG_BLK_DEV_IDE_SATA=n case (830 bytes saved on x86-32).

* Bump driver version.

Some minor cleanups while at it:

* Convert sil_{pata,sata}_udma_filter() to use ATA_UDMA* defines.

* In siimage_mmio_ide_dma_test_irq() move 'base' variable
  under 'if (SATA_ERROR_REG)' block.

* Simplify sil_sata_reset_poll() a bit.

* Cache is_sata() result in init_hwif_siimage() 
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:

generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method

it821x.c:
* if memory allocation fails drive->autotune won't be set
  (but there also won't be ->set_pio_mode method in such case)

piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)

However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so
they were not converted by commit 44c10138.

Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.

* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
  setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
  method may still override them).

* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.

While at it:

* Use ATA_{UDMA,MWDMA,SWDMA}* defines.

* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.

* serverworks.c: fix DMA masks being set before checking DMA base.

v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags.  Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define.  Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The siimage uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.

This fixes it by using the new ide_get_paired_drive() helper instead.

Bart: patch description fixes
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* hpt34x.c: disable DMA masks for HPT345
  (hwif->autodma is zero so DMA won't be enabled anyway).

* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
  (hwif->autodma is zero so DMA won't be enabled anyway).

* Check noautodma global variable instead of drive->autodma in ide_tune_dma().

  This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
  au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.

* Remove hwif->autodma (it was not checked by IDE core code anyway) and
  drive->autodma (was set by all host drivers - except HPT345/TRM290 special
  cases - unless "ide=nodma" was used).

While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
  (this setting was always later over-ridden by host drivers anyway)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check.  All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio()
  (->set_pio_mode method) so the controller is always programmed correctly for
  PIO transfers (this is important if DMA is not going to be used).

* Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset().

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets
  PIO mode on the device.

* Add missing ide_get_best_pio_mode() call to sil_tuneproc() so
  "pio" == 255 (autotune) is handled correctly (previously PIO0 was used)
  and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0).

* Add code limiting maximum PIO mode according to the pair device capabilities
  to sil_tuneproc().

* Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and
  sil_tuneproc().  This fixes PIO fallback in siimage_config_drive_for_dma() to
  use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio()
  used wrong arguments for ide_get_best_pio_mode() and as a results always
  tried to set PIO4).

* Remove no longer needed siimage_taskfile_timing()
  and config_siimage_chipset_for_pio().

* Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
  from siimage_speedproc()

* Bump driver version.

v2:
* Fix issues noticed by Sergei:
  - correct pair device check
  - trim only taskfile PIO to the slowest of the master/slave
  - enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
    from siimage_speedproc()
  - add TODO item for IORDY bugs
  - minor cleanups
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>