This patch adds support for USB dongle with device ID 3346 from IMC Networks.
Signed-off-by: NHaitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bit 22 of AR_WA should be set to fix the situation where chip reset
is asynchronous to clock of analog shift registers, such that when
reset is released, it could mess up the values of analog shift registers
and cause some hw issue on AR9280.

This bit is write only, but the driver does a read-modify-write
on AR_WA without setting bit 22 in ar9002_hw_configpcipowersave()
during radio disable. This causes surprise removal of hw. It can
never recover from this state and the hw will become usable only
after a power on/off cycle, and sometimes only during a cold reboot.

This issue can be triggered by doing frequent roaming with the
simple/test-roam script available from the wifi-test project [1]
when roaming between APs quickly. When roaming there is a is a high
possibility that the device being put into idle (radio disable) state
by mac80211 during AUTH->ASSOC. A device hardware reset would fail
and the kernel would output:

[40251.363799] ath: AWAKE -> FULL-SLEEP
[40251.363815] ieee80211 phy17: device no longer idle - working
[40251.363817] ath: Marking phy17 as not-idle
[40251.363819] ath: FULL-SLEEP -> AWAKE
[40251.415978] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[40251.419896] ath: ah->misc_mode 0x4
[40251.428138] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[40251.532247] ath: timeout (100000 us) on reg 0x9860: 0xffffffff & 0x00000001 != 0x00000000
[40251.532250] ath: Unable to reset channel (2462 MHz), reset status -5
[40251.532422] ath: Set channel: 5745 MHz
[40251.540639] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.548826] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.557023] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.565211] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.573415] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581603] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581606] ath: Failed to stop TX DMA. Resetting hardware!
[40251.592679] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff
[40251.703330] ath: timeout (100000 us) on reg 0x7000: 0xffffffff & 0x00000003 != 0x00000000
[40251.703333] ath: RTC stuck in MAC reset
[40251.703334] ath: Chip reset failed
[40251.703335] ath: Unable to reset hardware; reset status -22

This is currently only reproducible with some HB92 (Half Mini-PCIE)
cards but the fix applies to all AR9280 cards. This patch fixes this
issue by setting bit 22 during radio disable.

This patch has fixes for all kernels that has ath9k.

[1] http://wireless.kernel.org/en/developers/Testing/wifi-test

Cc: kyungwan.nam@atheros.com
Cc: amod.bodas@atheros.com
Cc: david.quan@atheros.com
Cc: stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are currently no provisions in place to ensure that the scanning
task has been stopped when the interface is stopped or removed.

This can result in a WARNING at net/wireless/core.c:643 and other badness
when you remove the module while a scan is happening.

Terminate the scanning task during interface stop.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For client STA interfaces, ieee80211_do_stop unsets the relevant
interface's SDATA_STATE_RUNNING state bit prior to cancelling an
interrupted scan.  When ieee80211_offchannel_return is invoked as
part of cancelling the scan, it doesn't bother unsetting the
SDATA_STATE_OFFCHANNEL bit because it sees that the interface is
down.  Normally this doesn't matter because when the client STA
interface is brought back up, it will probably issue a scan.  But
in some cases (e.g., the user changes the interface type while it
is down), the SDATA_STATE_OFFCHANNEL bit will remain set.  This
prevents the interface queues from being started.  So we
cancel the scan before unsetting the SDATA_STATE_RUNNING bit.
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_ps_wakeup() clears the cycle counters after waking up the
hardware using ath9k_hw_setpower, however if power save is disabled,
then the counters will contain useful data, which then gets discarded.
Fix this by checking the old power mode before discarding any data.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IS_ERR and PTR_ERR were called with the wrong pointer, leading to a
crash when cfg80211_get_dev_from_ifindex fails.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch includes the following updates:
 * add D-Link DWA-130 Rev D
 * Netgear has three WNDA3100 versions.
   the original WNDA3100 is now called WNDA3100v1.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Throughput was severely affected in Intel Pinetrail platforms
because of a DMA problem in C3 state. This patch fixes this
issue.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HW opmode is blindly set to monitor type on monitor mode
change notification. This overrides the opmode when one of the
interfaces is still running as non-monitor iftype. So the monitoring
information needs to be maintained seperately.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This bug seems to be due to commit 27ae60f8 ("ipw2x00: replace
"ieee80211" with "libipw" where appropriate"), where Pavel did this:

-       libipw_proc = proc_mkdir(DRV_NAME, init_net.proc_net);
+       libipw_proc = proc_mkdir("ieee80211", init_net.proc_net);

but then the cleanup was kept as

        remove_proc_entry(DRV_NAME, init_net.proc_net);

in both places (both in the failure case and in the unload case). The
error string is also total crap, and says

     "Unable to create " DRV_NAME " proc directory\n");

Even though it doesn't actually create a proc directory named DRV_NAME at all.

So that patch looks like total and utter crap to me. The commit message says

  "Keep /proc/net/ieee80211 under the original name to avoid breaking user
    interface."

but the thing is, it really didn't fix anything but that one create
thing. It needs to fix all the other cases too.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On module removal, the sdio version of b43 generates the following warning:

[  851.560519] ------------[ cut here ]------------
[  851.560531] WARNING: at drivers/mmc/core/core.c:237 mmc_wait_for_cmd+0x88/0x90()
[  851.560534] Hardware name: 20552PG
[  851.560536] Modules linked in: b43(-) ssb mmc_block binfmt_misc rfcomm sco bnep ppdev l2cap ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp kvm_intel kvm arc4 iwlagn snd_hda_codec_conexant snd_hda_intel snd_hda_codec iwlcore snd_hwdep snd_pcm thinkpad_acpi mac80211 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq r852 joydev snd_timer sm_common pcmcia nand snd_seq_device cfg80211 sdhci_pci btusb psmouse tpm_tis yenta_socket nand_ids lp snd pcmcia_rsrc nand_ecc bluetooth sdhci tpm pcmcia_core parport mtd snd_page_alloc serio_raw tpm_bios soundcore nvram led_class sha256_generic aes_i586 aes_generic dm_crypt i915 drm_kms_helper drm ahci intel_agp i2c_algo_bit intel_gtt e1000e libahci video agpgart output
[  851.560620] Pid: 2504, comm: rmmod Not tainted 2.6.36-titan0+ #1
[  851.560622] Call Trace:
[  851.560631]  [<c014a102>] warn_slowpath_common+0x72/0xa0
[  851.560636]  [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90
[  851.560641]  [<c04d94c8>] ? mmc_wait_for_cmd+0x88/0x90
[  851.560645]  [<c014a152>] warn_slowpath_null+0x22/0x30
[  851.560649]  [<c04d94c8>] mmc_wait_for_cmd+0x88/0x90
[  851.560655]  [<c0401585>] ? device_release+0x25/0x80
[  851.560660]  [<c04df210>] mmc_io_rw_direct_host+0xa0/0x150
[  851.560665]  [<c04df370>] mmc_io_rw_direct+0x30/0x40
[  851.560669]  [<c04e06e7>] sdio_disable_func+0x37/0xa0
[  851.560683]  [<f8dfcb80>] b43_sdio_remove+0x30/0x50 [b43]
[  851.560687]  [<c04df8cc>] sdio_bus_remove+0x1c/0x60
[  851.560692]  [<c016d39f>] ? blocking_notifier_call_chain+0x1f/0x30
[  851.560697]  [<c0404991>] __device_release_driver+0x51/0xb0
[  851.560701]  [<c0404a7f>] driver_detach+0x8f/0xa0
[  851.560705]  [<c0403c83>] bus_remove_driver+0x63/0xa0
[  851.560709]  [<c0405039>] driver_unregister+0x49/0x80
[  851.560713]  [<c0405039>] ? driver_unregister+0x49/0x80
[  851.560718]  [<c04dfad7>] sdio_unregister_driver+0x17/0x20
[  851.560727]  [<f8dfcb42>] b43_sdio_exit+0x12/0x20 [b43]
[  851.560734]  [<f8dfe76f>] b43_exit+0x17/0x3c [b43]
[  851.560740]  [<c017fb8d>] sys_delete_module+0x13d/0x200
[  851.560747]  [<c01fd7d2>] ? do_munmap+0x212/0x300
[  851.560752]  [<c010311f>] sysenter_do_call+0x12/0x28
[  851.560757] ---[ end trace 31e14488072d2f7d ]---
[  851.560759] ------------[ cut here ]------------

The warning is caused by b43 not claiming the device before calling
sdio_disable_func().
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: NArnd Hannemann <arnd@arndnet.de>
Tested-by: NArnd Hannemann <arnd@arndnet.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed two small issues in mac80211/debugfs_key.c::key_key_read while
reading through the code. Patch below.

The key_key_read() function returns ssize_t and the value that's actually
returned is the return value of simple_read_from_buffer() which also
returns ssize_t, so let's hold the return value in a ssize_t local
variable rather than a int one.

Also, memory is allocated dynamically with kmalloc() which can fail, but
the return value of kmalloc() is not checked, so we may end up operating
on a null pointer further on. So check for a NULL return and bail out with
-ENOMEM in that case.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For the SD8686, we cannot rely on the scratch register to read the firmware
load status, because the same register is used for storing RX packet length.
Broaden the check to account for this.

The module can now be unloaded/reloaded successfully.

Based on the implementation from libertas_tf.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NSteve deRosier <steve@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The index variable to access the rate flags should be obtained from the
inner loop counter which corresponds to the rate table structure.This
fixes the invalid rate selection i.e when the supported basic rate is
invalid on a particular band and also the following warning message.
Thanks to Raj for finding this out.

Call Trace:

 [<ffffffff8104ee4a>] warn_slowpath_common+0x7a/0xb0

 [<ffffffff8104ee95>] warn_slowpath_null+0x15/0x20

 [<ffffffffa0583c45>] ath_get_rate+0x595/0x5b0 [ath9k]

 [<ffffffff811a0636>] ? cpumask_next_and+0x36/0x50

 [<ffffffffa0405186>] rate_control_get_rate+0x86/0x160 [mac80211]

 [<ffffffffa040dfac>] invoke_tx_handlers+0x81c/0x12d0 [mac80211]

 [<ffffffffa040eae9>] ieee80211_tx+0x89/0x2b0 [mac80211]

 [<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0

 [<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211]

 [<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211]

 [<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]

 [<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150
[mac80211]

 [<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0

 [<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211]

 [<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211]

 [<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]

 [<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150
[mac80211]

 [<ffffffffa03f8896>] ieee80211_scan_work+0x146/0x600 [mac80211]

 [<ffffffff8133a375>] ? schedule+0x2f5/0x8e0

 [<ffffffffa03f8750>] ? ieee80211_scan_work+0x0/0x600 [mac80211]

 [<ffffffff81064fcf>] process_one_work+0x10f/0x380

 [<ffffffff81066bc2>] worker_thread+0x162/0x340

 [<ffffffff81066a60>] ? worker_thread+0x0/0x340

Cc: stable@kernel.org
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If ath5k_hw_attach fails it will free sc->ah (local variable ah) before
returning. However, when it reports failure the caller (ath5k_pci_probe)
will also free sc->ah. Let the caller handle the deallocation, it does
so on further errors as well.
Signed-off-by: NJones Desougi <jones.desougi@27m.se>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 651b5225 added DS Parameter Set
information into Probe Request frames that are transmitted on 2.4 GHz
band, but it failed to increment local->scan_ies_len to cover this new
information. This variable needs to be updated to match the maximum IE
data length so that the extra buffer need gets reduced from the driver
limit.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Netgear WNDA3200 device uses ar7010 firmware but it is failed to set
correct firmware offset on firmware download which causes device initialization
failure.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Completing aggregate frames can lead to new buffers being pushed into
the tid queues due to software retransmission.
When the tx queues are being drained, all pending aggregates must be
completed before the tid queues get drained, otherwise buffers might be
leaked.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apart from locking the start and stop PCU we need
to ensure we also content starting and stopping the PCU
between hardware resets.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The real way to lock RX is to contend on the PCU
and reset, this will be fixed in the next patch but for
now just do the renames so that the next patch which changes
the locking order is crystal clear.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was some locking for starting some parts of
RX but not for starting the PCU. Include this otherwise
we can content against stopping the PCU.

This can potentially lead to races against different
buffers on the PCU which can lead to to the DMA RX
engine writing to buffers which are already freed.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k locks for starting RX but not for stopping RX. We could
potentially run into a situation where tried to stop RX
but immediately started RX. This allows for races on the
the RX engine deciding what buffer we last left off on
and could potentially cause ath9k to DMA into already
free'd memory or in the worst case at a later time to
already given memory to other drivers.

Fix this by locking stopping RX.

This is part of a series that will help resolve the bug:

https://bugzilla.kernel.org/show_bug.cgi?id=14624

For more details about this issue refer to:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Timing issues in microcode for some devices can cause a compressed BA to
be sent to the driver prior to returning any a-MPDU notification.
Traces show RTS-CTS is exchanged and then the timer fires which causes an
empty BA to be sent which acknowledges nothing.  This results in a noisy
printk. Only print the message if the bitmap is non-zero.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since aggregation is usually triggered by tx completion, a hardware
reset (because of beacon stuck, tx hang or baseband hang) can
significantly delay the transmission of the next AMPDU (until the next
tx completion event).
Fix this by rescheduling aggregation after such a reset.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the following mishap:

BUG: scheduling while atomic: wpa_supplicant/4164/0x00000002
Modules linked in: carl9170 mac80211 [...]
Pid: 4164, comm: wpa_supplicant Not tainted 2.6.36-wl+ #119
Call Trace:
 [<c13779a9>] ? schedule+0x349/0x4c0
 [<c13780d6>] ? schedule_timeout+0x106/0x1e0
 [<c1037f50>] ? process_timeout+0x0/0x10
 [<c1377e8d>] ? wait_for_common+0x9d/0x140
 [<c1029110>] ? default_wake_function+0x0/0x10
 [<f80c6080>] ? carl9170_exec_cmd+0xf0/0x250 [carl9170]
 [<f80c695e>] ? carl9170_set_mac_reg+0x5e/0x70 [carl9170]
 [<f80c3f76>] ? carl9170_op_add_interface+0x176/0x310 [carl9170]
 [...]

rcu_read_unlock() call was erroneously placed after the
sync. function carl9170_mod_virtual_mac.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Station addition in ieee80211_ibss_rx_queued_mgmt is not updating
sta->last_rx which is causing station expiry in ieee80211_ibss_work
path. So sta addition and deletion happens repeatedly.

CC: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The wl1251 move accidently renamed wl1251_sdio and wl1251_spi
modules to just sdio and spi. Restore proper module names.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k aggregation code was already checking the rate control probe flag
to prevent starting an aggregate frame with a sampling rate. What was missing
was closing an aggregate before adding a probing frame to it.
Without that, rate control cannot have precise control over probing, which
delays using faster rates when the channel conditions improve.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If ah->curchan is uninitialized, the channel index is bogus, which leads
to invalid memory access when the cycle counters are updated.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We are not handling all divide by zero cases in paprd.
Add additional checks for divide by zero cases in papard.

This patch has fixes intended for kernel 2.6.36.

Cc: stable@kernel.org
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates the initvals for the AR9003 2.2 chipsets. The initvals
are the initial register values we use for our registers upon hardware
reset. This synchs up the initvals to match what our latest recommendation
from our systems engineering team.

The description of changes in this update:

        Improves ability to support very strong Rx conditions.
        Enhances DFS support for AP-mode.
        Improves performance of Tx carrier leak calibration.
        Adds support for Japan channel 14 Tx filtering requirements.
        Improves Tx power accuracy.

Impact:

        Update required to address degraded throughput at very short range.
        Update required for AP-mode DFS certification.
        Update required to comply to IEEE Tx carrier leak specification.
        May not meet expected +/- 2 dB Tx power accuracy without update.

The most important fix here would be the TX carrier leakage required
to comply with IEEE 802.11 specifications. The group of changes have
been tested all together in one release.

References:

	Osprey 2.2 header file ver #33

Checksums:

$ ./initvals -f ar9003-2p2
0x000000004a488fc7        ar9300_2p2_radio_postamble
0x0000000046cb1300        ar9300Modes_lowest_ob_db_tx_gain_table_2p2
0x00000000e912711f        ar9300Modes_fast_clock_2p2
0x0000000037ac0ee8        ar9300_2p2_radio_core
0x00000000047a7700        ar9300Common_rx_gain_table_merlin_2p2
0x0000000003f783bb        ar9300_2p2_mac_postamble
0x00000000301fc841        ar9300_2p2_soc_postamble
0x000000005ec8075f        ar9200_merlin_2p2_radio_core
0x0000000083372ffa        ar9300_2p2_baseband_postamble
0x00000000c4f59974        ar9300_2p2_baseband_core
0x00000000e20d2e72        ar9300Modes_high_power_tx_gain_table_2p2
0x000000007fd55c70        ar9300Modes_high_ob_db_tx_gain_table_2p2
0x0000000029495000        ar9300Common_rx_gain_table_2p2
0x0000000042cb1300        ar9300Modes_low_ob_db_tx_gain_table_2p2
0x00000000c4739cd6        ar9300_2p2_mac_core
0x000000003521a300        ar9300Common_wo_xlna_rx_gain_table_2p2
0x00000000a15ccf1b        ar9300_2p2_soc_preamble
0x0000000029734396        ar9300PciePhy_pll_on_clkreq_disable_L1_2p2
0x000000002d834396        ar9300PciePhy_clkreq_enable_L1_2p2
0x0000000029834396        ar9300PciePhy_clkreq_disable_L1_2p2

$ ./initvals -f ar9003-2p2 | sha1sum
0ceddb5cf66737610fb51f04cf3e9ff71870c7b4  -

Cc: stable@kernel.org
Cc: Yixiang Li <yixiang.li@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch 4f366c5d:

	wireless: only use alpha2 regulatory information from country IE

removed some complex intersection we were always doing between the AP's
country IE info and what we got from CRDA. When CRDA sent us back a
regulatory domain we would do some sanity checks on that regulatory
domain response we just got. Part of these sanity checks included
checking that we already had performed an intersection for the
request of NL80211_REGDOM_SET_BY_COUNTRY_IE type.

This mean that cfg80211 was only processing country IEs for cases
where we already had an intersection, but since we removed enforcing
this this is no longer required, we should just apply the country
IE country hint with the data received from CRDA.

This patch has fixes intended for kernels >= 2.6.36.

Cc: stable@kernel.org
Reported-by: NEaswar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch continues where the previous commit:
	"carl9170: fix async command buffer leak"
left off.

Similar to carl9170_reboot/carl9170_powersave, the
carl9170_async_regwrite* macros would leak the
temporary command buffer, if __carl9170_exec_cmd
fails to upload the command to the device.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I found this bug while poking around with a pure-gn AP.

Commit:
cfg80211/mac80211: Use more generic bitrate mask for rate control

Added some sanity checks to ensure that each tx rate index
is included in the configured mask and it would change any
rate indexes if it wasn't.

But, the current implementation doesn't take into account
that the invalid rate index "-1" has a special meaning
(= no further attempts) and it should not be "changed".
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If __carl9170_exec_cmd fails to upload an asynchronous
command to the device, the functions: carl9170_reboot
and carl9170_powersave will leak the temporary command
assembly buffer.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, lockdep splats, at the least:

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 0, comm: swapper Not tainted 2.6.36-rc8-wl+ #32
Call Trace:
 [<c075d940>] ? printk+0xf/0x17
 [<c045507a>] register_lock_class+0x5a/0x29e
 [<c0456af5>] __lock_acquire+0xa2/0xb8c
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c041a540>] ? acpi_get_override_irq+0x85/0x8c
 [<c0455536>] ? trace_hardirqs_off+0xb/0xd
 [<c0457639>] lock_acquire+0x5a/0x78
 [<f8126835>] ? ath5k_ani_calibration+0x24/0x52b [ath5k]
 [<c075f6ed>] _raw_spin_lock_bh+0x20/0x2f
 [<f8126835>] ? ath5k_ani_calibration+0x24/0x52b [ath5k]
 [<f8126835>] ath5k_ani_calibration+0x24/0x52b [ath5k]
 [<c0438f99>] ? tasklet_action+0x3b/0xc6
 [<f8123c2b>] ath5k_tasklet_ani+0x18/0x22 [ath5k]
 [<c0438fd1>] tasklet_action+0x73/0xc6
 [<c043945f>] __do_softirq+0x86/0x111
 [<c0439520>] do_softirq+0x36/0x5a
 [<c0439659>] irq_exit+0x35/0x69
 [<c0403fb9>] do_IRQ+0x86/0x9a
 [<c04034ee>] common_interrupt+0x2e/0x40
 [<c045007b>] ? do_adjtimex+0x223/0x55e
 [<c0408245>] ? mwait_idle+0x5c/0x6c
 [<c040227f>] cpu_idle+0x4e/0x6b
 [<c074b6e9>] rest_init+0x8d/0x92
 [<c09758ea>] start_kernel+0x320/0x325
 [<c09750d0>] i386_start_kernel+0xd0/0xd7
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, lockdep splats, at the least:

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2240, comm: ip Not tainted 2.6.36-rc8-wl+ #32
Call Trace:
 [<c075d940>] ? printk+0xf/0x17
 [<c045507a>] register_lock_class+0x5a/0x29e
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0456af5>] __lock_acquire+0xa2/0xb8c
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0457639>] lock_acquire+0x5a/0x78
 [<f8c5115b>] ? ath9k_config+0x274/0x3d8 [ath9k]
 [<c075f602>] _raw_spin_lock_irqsave+0x2f/0x3f
 [<f8c5115b>] ? ath9k_config+0x274/0x3d8 [ath9k]
 [<f8c5115b>] ath9k_config+0x274/0x3d8 [ath9k]
 [<f8c0ba2e>] ieee80211_hw_config+0x11b/0x125 [mac80211]
 [<f8c17edf>] ieee80211_do_open+0x3c5/0x466 [mac80211]
 [<f8c171d6>] ? ieee80211_check_concurrent_iface+0x21/0x13a [mac80211]
 [<f8c17fdb>] ieee80211_open+0x5b/0x5e [mac80211]
 [<c06ce76b>] __dev_open+0x80/0xae
 [<c06cc99b>] __dev_change_flags+0xa0/0x115
 [<c06ce6bf>] dev_change_flags+0x13/0x3f
 [<c06d7e78>] do_setlink+0x23a/0x51b
 [<c0455037>] ? register_lock_class+0x17/0x29e
 [<c06d847c>] rtnl_newlink+0x269/0x431
 [<c06d8291>] ? rtnl_newlink+0x7e/0x431
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0455de9>] ? mark_held_locks+0x47/0x5f
 [<c075ebcf>] ? __mutex_lock_common+0x2bb/0x2d6
 [<c0456045>] ? trace_hardirqs_on_caller+0x104/0x125
 [<c075ebe0>] ? __mutex_lock_common+0x2cc/0x2d6
 [<c06d8213>] ? rtnl_newlink+0x0/0x431
 [<c06d79e2>] rtnetlink_rcv_msg+0x182/0x198
 [<c06d7860>] ? rtnetlink_rcv_msg+0x0/0x198
 [<c06e503c>] netlink_rcv_skb+0x30/0x77
 [<c06d7859>] rtnetlink_rcv+0x1b/0x22
 [<c06e4e77>] netlink_unicast+0xbe/0x119
 [<c06e5a15>] netlink_sendmsg+0x234/0x24c
 [<c06bf93a>] __sock_sendmsg+0x51/0x5a
 [<c06bfba4>] sock_sendmsg+0x93/0xa7
 [<c04968cf>] ? might_fault+0x47/0x81
 [<c0496904>] ? might_fault+0x7c/0x81
 [<c06c7904>] ? copy_from_user+0x8/0xa
 [<c06c7c2d>] ? verify_iovec+0x3e/0x6d
 [<c06bfd8c>] sys_sendmsg+0x149/0x193
 [<c0455037>] ? register_lock_class+0x17/0x29e
 [<c0455be2>] ? mark_lock+0x1e/0x1de
 [<c0498d7a>] ? __do_fault+0x1fc/0x3a5
 [<c048690a>] ? unlock_page+0x40/0x43
 [<c0498ef7>] ? __do_fault+0x379/0x3a5
 [<c04576dd>] ? lock_release_non_nested+0x86/0x1d8
 [<c04968cf>] ? might_fault+0x47/0x81
 [<c04968cf>] ? might_fault+0x47/0x81
 [<c06c148b>] sys_socketcall+0x15e/0x1a5
 [<c0402f1c>] sysenter_do_call+0x12/0x38
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iee80211_hw->restart_work is the only work which uses the system
workqueue.  Instead of calling flush_scheduled_work() during
iee80211_exit(), cancel the work during unregistration.

This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  Update broken web addresses in arch directory.
  Update broken web addresses in the kernel.
  Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
  Revert "Fix typo: configuation => configuration" partially
  ida: document IDA_BITMAP_LONGS calculation
  ext2: fix a typo on comment in ext2/inode.c
  drivers/scsi: Remove unnecessary casts of private_data
  drivers/s390: Remove unnecessary casts of private_data
  net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
  drivers/infiniband: Remove unnecessary casts of private_data
  drivers/gpu/drm: Remove unnecessary casts of private_data
  kernel/pm_qos_params.c: Remove unnecessary casts of private_data
  fs/ecryptfs: Remove unnecessary casts of private_data
  fs/seq_file.c: Remove unnecessary casts of private_data
  arm: uengine.c: remove C99 comments
  arm: scoop.c: remove C99 comments
  Fix typo configue => configure in comments
  Fix typo: configuation => configuration
  Fix typo interrest[ing|ed] => interest[ing|ed]
  Fix various typos of valid in comments
  ...

Fix up trivial conflicts in:
	drivers/char/ipmi/ipmi_si_intf.c
	drivers/usb/gadget/rndis.c
	net/irda/irnet/irnet_ppp.c