There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks

Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.

fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.

Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Simplify confusing code and get rid of an unnecessary variable.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When beacons are being added or removed for an interface, ieee80211_beacon_get
will sometimes not return a beacon. This is normal and should not result in
useless logspam.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove sc->curband because the band is already stored in the current channel.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sc->curmode is set but never used. Remove it and the helper function. Also the
ath5k_rate_update which is refered to in the comment does not exist (any more?)
so we don't need to setup the band in that place.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

They are unused in ath5k and a more detailled definition is in
ath/regd_common.h.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the 802.11j (20MHz channel width) channels to the allowed channels. This
still does not enable 802.11j in ath5k since these frequencies are out of the
configured range. A later patch will deal with that.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename ath5k_copy_channels() to ath5k_setup_channels() - nothing is copied
here.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use mac80211 channel mapping function instead of own homegrown version.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Try all xmit queues until the hardware buffers are full.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a misc file to show hardware op-mode, irq setup,
number of various types of VIFs and more.

Also, previous patches were using the wrong xmit queue
indexes.  Change to use the internal ath9k indexes instead
of the mac80211 queue indexes.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.

This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.

The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NBrian Prodoehl <bprodoehl@gmail.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The system can get into a state where the xmit queue
is stopped, but there are no packets pending, so
the queue will not be restarted.

Add logic to the xmit watchdog to attempt to restart
the xmit logic if this situation is detected.

Example 'dmesg' output:

ath: txq: f4e723e0 axq_qnum: 2, mac80211_qnum: 2 axq_link: f4e996c8 pending frames: 1 axq_acq empty: 1 stopped: 0 axq_depth: 0  Attempting to restart tx logic.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To try to figure out why xmit logic hangs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The stations hold the ath_node, which holds the tid
and other xmit logic structures.  In order to debug
stuck xmit logic, we need a way to print out the tid
state for the stations.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Show counters for pkts sent directly to hardware and
those queued in software.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the txq->axq_q is empty, the code was breaking out
of the tx_processq logic without checking to see if it should
transmit other queued AMPDU frames (txq->axq_acq).

This patches ensures ath_txq_schedule is called.

This needs review.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Should help debug strange tx lockup type issues.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previous code left it NULL.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I thought this might help track down stuck queues, etc.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This particular error isn't about multicast.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The notification wait support code is shared
between 4965 and other AGN devices, so 4965
also has to initialize the data structures
for it, otherwise it crashes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously I hacked this with an msleep(300)
which was fine since we never had longer PAN
time slots, but now that we will have them I
need to fix that. Use the new notification
wait support to properly wait for the WIPAN
deactivation complete signal from the ucode.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to implement waiting for notifications,
add a structure that captures the information,
and a list of such structures that will be
traversed when a command is received from the
ucode.

Use sparse checking to make sure calls to the
prepare/wait/cancel functions are always nested
correctly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not used or likely to be needed from other
files, so it can be static.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When running as a 4-addr station against an AP that has the 4-addr VLAN
interface and the main 3-addr AP interface bridged together, sometimes
frames originating from the station were looping back from the 3-addr AP
interface, causing the bridge code to emit warnings about receiving frames
with its own source address.
I'm not sure why this is happening yet, but I think it's a good idea to
drop all frames (except 802.1x/EAP frames) that do not match the configured
addressing mode, including 4-address frames sent to a 3-address station.
User test reports indicate that the problem goes away with this patch.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, mac80211 always advertises that it may send
up to 64 subframes in an aggregate. This is fine, since
it's the max, but might as well be set to zero instead
since it doesn't have any information.

However, drivers might have that information, so allow
them to set a variable giving it, which will then be
used. The default of zero will be fine since to the
peer that means we don't know and it will just use its
own limit for the buffer size.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.

In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.

Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mesh is disabled, mac80211 was returning
beacons with an empty mesh ID. That isn't
desirable, even if drivers shouldn't be trying
to get beacons to start with.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered.  Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.

In addtion, use the vif type instead of hardware opmode
when dealing with beacons.

Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9285 carrier leakage calibration related workaround on high
temperature is not applicable for AR9271.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mppath is mesh related parameter and maybe unused
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>