In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.

Fixes: 450b05c1 ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: NStefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:

drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]

This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.

Fixes: a0627f77 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: NIvan Vecera <cera@cera.cz>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename functions to avoid _ prefix.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename to mv88e6390_g1_stats_set_histogram
  Move into global1.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

_mv88e6xxx_stats_wait() did not check the return value from
 mv88e6xxx_g1_read(), so the compiler complained about set but unused
 err.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Declare the structure ieee802154_ops as const as it is only passed as an
argument to the function  ieee802154_alloc_hw. This argument is of type
const struct ieee802154_ops *, so ieee80254_ops structures having this
property can be declared as const.
Done using Coccinelle:

@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ieee802154_ops i@p = {...};

@ok1@
identifier r1.i;
position p;
expression e1;
@@
ieee802154_alloc_hw(e1,&i@p)

@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ieee802154_ops  i={...};

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ieee802154_ops  i;

The before and after size details of the affected files are:

   text	   data	    bss	    dec	    hex	filename
   8669	   1176	     16	   9861	   2685	drivers/net/ieee802154/adf7242.o
   8805	   1048	     16	   9869	   268d	drivers/net/ieee802154/adf7242.o

   text	   data	    bss	    dec	    hex	filename
   7211	   2296	     32	   9539	   2543	drivers/net/ieee802154/atusb.o
   7339	   2160	     32	   9531	   253b	drivers/net/ieee802154/atusb.o
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Acked-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than comparing 64-bit tunnel-id, compare tunnel vni
which is 24-bit id. This also save conversion from vni
to tunnel id on each tunnel packet receive.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geneve already has check for device socket in route
lookup function. So no need to check it in xmit
function.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are minimal difference in building Geneve header
between ipv4 and ipv6 geneve tunnels. Following patch
refactors code to unify it.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current geneve implementation has two separate cases to handle.
1. netdev xmit
2. LWT xmit.

In case of netdev, geneve configuration is stored in various
struct geneve_dev members. For example geneve_addr, ttl, tos,
label, flags, dst_cache, etc. For LWT ip_tunnel_info is passed
to the device in ip_tunnel_info.

Following patch uses ip_tunnel_info struct to store almost all
of configuration of a geneve netdevice. This allows us to unify
most of geneve driver code around ip_tunnel_info struct.
This dramatically simplify geneve code, since it does not
need to handle two different configuration cases. Removes
duplicate code, single code path can handle either type
of geneve devices.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function macvlan_forward_source_one has already checked the flag
IFF_UP, so needn't check it outside in macvlan_forward_source too.
Signed-off-by: NGao Feng <gfree.wind@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's not much point, except compile test, enabling the stmmac
platform drivers unless the STM32 SoC is enabled. It's not
useful without it.
Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While stressing a 40Gbit mlx4 NIC with busy polling, I found false
sharing in mlx4 driver that can be easily avoided.

This patch brings an additional 7 % performance improvement in UDP_RR
workload.

1) If we received no frame during one mlx4_en_process_rx_cq()
   invocation, no need to call mlx4_cq_set_ci() and/or dirty ring->cons

2) Do not refill rx buffers if we have plenty of them.
   This avoids false sharing and allows some bulk/batch optimizations.
   Page allocator and its locks will thank us.

Finally, mlx4_en_poll_rx_cq() should not return 0 if it determined
cpu handling NIC IRQ should be changed. We should return budget-1
instead, to not fool net_rx_action() and its netdev_budget.

v2: keep AVG_PERF_COUNTER(... polled) even if polled is 0
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

barrier() is a big hammer compared to READ_ONCE(),
and requires comments explaining what is protected.

READ_ONCE() is more precise and compiler should generate
better overall code.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx5e_xdp_set() is currently the only place where we drop reference on the
prog sitting in priv->xdp_prog when it's exchanged by a new one. We also
need to make sure that we eventually release that reference, for example,
in case the netdev is dismantled, otherwise we leak the program.

Fixes: 86994156 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are multiple issues in mlx5e_xdp_set():

1) The batched bpf_prog_add() is currently not checked for errors. When
   doing so, it should be done at an earlier point in time to makes sure
   that we cannot fail anymore at the time we want to set the program for
   each channel. The batched refs short-cut can only be performed when we
   don't need to perform a reset for changing the rq type and the device
   was in opened state. In case the device was not in opened state, then
   the next mlx5e_open_locked() will aquire the refs from the control prog
   via mlx5e_create_rq(), same when we need to perform a reset.

2) When swapping the priv->xdp_prog, then no extra reference count must be
   taken since we got that from call path via dev_change_xdp_fd() already.
   Otherwise, we'd never be able to release the program. Also, bpf_prog_add()
   without checking the return code could fail.

Fixes: 86994156 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In mlx5e_create_rq(), when creating a new queue, we call bpf_prog_add() but
without checking the return value. bpf_prog_add() can fail since 92117d84
("bpf: fix refcnt overflow"), so we really must check it. Take the reference
right when we assign it to the rq from priv->xdp_prog, and just drop the
reference on error path. Destruction in mlx5e_destroy_rq() looks good, though.

Fixes: 86994156 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing interrupts requires switch register access to mask the
interrupts. Hence we must hold the register mutex.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not possible to use devm_request_threaded_irq() because we have
two stacked interrupt controllers in one device. The lower interrupt
controller cannot be removed until the upper is fully removed. This
happens too late with the devm API, resulting in error messages about
removing a domain while there is still an active interrupt. Swap to
using request_threaded_irq() and manage the release of the interrupt
manually.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On error, remask the interrupts, release all maps, and remove the
domain. This cannot be done using the mv88e6xxx_g1_irq_free() because
some of these actions are not idempotent.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the g1 interrupt free code such that is masks any further
interrupts, and then releases the interrupt.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trying to remove an IRQ domain that was not created results in an
Opps. Add the necessary checks that the irqs were created before
freeing them.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simple typos, s/g2/g1/
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

virtio_net_hdr_from_skb() clears the memory for the header, so there
is no point for the callers to do the same.
Signed-off-by: NJarno Rajahalme <jarno@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>