Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add missing entries to nl80211.h and fix
the kernel-doc notation in cfg80211.h.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It should be NL80211_SCHED_SCAN_MATCH_ATTR_SSID as
documented, not NL80211_ATTR_SCHED_SCAN_MATCH_SSID.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If you add a monitor interface in parallel to a normal interface
mac80211 will let you to change the channel type on the monitor
interface even if you are connected. Add an explicit check to
disallow this.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
[fix typo in commit log, use sdata instead of netdev]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In my redesign of remain-on-channel I forgot
that an item could be cancelled when it's a
dependent item that is part of another item.
Allow cancelling such items by removing them
from the dependents list.

Note that when we cancel the main item, all
its dependents are also cancelled. It would
be possible to not do that, but would need
tricks to promote an item from dependent to
top-level and is tricky in the HW ROC case.
Reported-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Reference: http://standards.ieee.org/develop/regauth/oui/oui.txtSigned-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Ilan pointed out to me that ieee80211_start_next_roc()
already calls ieee80211_run_deferred_scan() if the list
of ROC items is empty, so there's no need to call it
again after calling ieee80211_start_next_roc().
Reported-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add the missing kernel-doc for mesh configuration parameters as pointed
out by Johannes Berg.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Reviewed-by: NJason Abele <jason@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Reviewed-by: NJason Abele <jason@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

  CC      drivers/net/wireless/ti/wl18xx/main.o
drivers/net/wireless/ti/wl18xx/main.c: In function ‘wl18xx_conf_init’:
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘long unsigned int’ [-Wformat]
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't spew errors when we can't find the NVS file in wlcore. Instead
fail the wl12xx boot HW op if the NVS isn't found.

Take this opportunity to remove some dead code from register_hw()
which looks for the NVS again needlessly.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Give all wl18xx phy module paramters -1 as a default value, indicating
the paramter was not set. Add previous default values to the default
18xx priv conf structure.

Remove the board_type field from wl18xx priv. The field with the same
name inside the phy conf is good enough for our purposes.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params
structure. Remove it and replace the phy part of the wl18xx conf with the
FW bound structure. This allows us to set/override all members.

Increment the wlconf version to ensure compatibility with the new
structure
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries
accordingly.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This is supported by new FW versions (.88+).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Instead of using the hardcoded configuration structure, try to read it
from a "firmware" file called wl18xx-conf.bin.  If the file doesn't
exist, fall back to the hardcoded version.  If the file exists but is
illegal, bail out.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add conf file header structure, magic and version values and export
the entire conf struct in debugfs.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Since we are now going to export the conf structure and read it from a
file, it should be packed to avoid surprises with padding bytes.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Since we will export the conf structure as a file, we need to use well
defined types.  Instead of using enum, whose size may vary, use u8 for
bcn_filt_mode instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The conf structure is going to be exported to a file, so we should use
only well defined types.  bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Instead of parsing all the binary data returned by the firmware, we
should simply export the binary and let the userspace do the parsing.

This commit adds a new file to debugfs to do that.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics.  The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add support for an external 26 MHz crystal source.

[Changed wl->ref_clock to priv->ref_clock -- Luca.]
Signed-off-by: NGrant Erickson <marathon96@gmail.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.

[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]

[Make the pre_pkt_send operation optional -- Luca]
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).

[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
Signed-off-by: NOrit Brayer <orit@ti.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

PG2 requires 4 new parameters that to be passed to the PHY.

Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.

[Make sure PG1 still gets the original struct - Arik]
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

PG2 has a unique chip id. It supports similar HW quirks.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

was hardcoded 252, now uses the parameters struct size.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.

This fixes a number of small issues with the ROC
implementation:
 * offloaded remain-on-channel couldn't be queued,
   now we can queue it as well, if needed
 * in iwlwifi (the only user) offloaded ROC is
   mutually exclusive with scanning, use the new
   queue to handle that case -- I expect that it
   will later depend on a HW flag

The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.

The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.

Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.

Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.

Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The preferred URL is http://wireless.kernel.org/
rather than http://linuxwireless.org/, update all
URLs to point there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately.  Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>