VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: NJakob Haufe <sur5r@sur5r.net>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx is oopsing with some DVB devices:

[10856.061884] general protection fault: 0000 [#1] SMP
[10856.067041] Modules linked in: rc_hauppauge em28xx_rc xc5000 drxk em28xx_dvb dvb_core em28xx videobuf2_vmalloc videobuf2_memops videobuf2_core rc_pixelview_new tuner_xc2028 tuner cx8800 cx88xx tveeprom btcx_risc videobuf_dma_sg videobuf_core rc_core v4l2_common videodev ebtable_nat ebtables nf_conntrack_ipv4 nf_defrag_ipv4 xt_CHECKSUM be2iscsi iscsi_boot_sysfs iptable_mangle bnx2i cnic uio cxgb4i cxgb4 tun bridge cxgb3i cxgb3 stp ip6t_REJECT mdio libcxgbi nf_conntrack_ipv6 llc nf_defrag_ipv6 ib_iser rdma_cm ib_addr xt_conntrack iw_cm ib_cm ib_sa nf_conntrack ib_mad ib_core bnep bluetooth iscsi_tcp libiscsi_tcp ip6table_filter libiscsi ip6_tables scsi_transport_iscsi xfs libcrc32c snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm tg3 snd_page_alloc snd_timer
[10856.139176]  snd ptp iTCO_wdt soundcore pps_core iTCO_vendor_support lpc_ich mfd_core coretemp nfsd hp_wmi crc32c_intel microcode serio_raw rfkill sparse_keymap nfs_acl lockd sunrpc kvm_intel kvm uinput binfmt_misc firewire_ohci nouveau mxm_wmi i2c_algo_bit drm_kms_helper firewire_core crc_itu_t ttm drm i2c_core wmi [last unloaded: dib0070]
[10856.168969] CPU 1
[10856.170799] Pid: 13606, comm: dvbv5-zap Not tainted 3.9.0-rc5+ #26 Hewlett-Packard HP Z400 Workstation/0AE4h
[10856.181187] RIP: 0010:[<ffffffffa0459e47>]  [<ffffffffa0459e47>] em28xx_write_regs_req+0x37/0x1c0 [em28xx]
[10856.191028] RSP: 0018:ffff880118401a58  EFLAGS: 00010282
[10856.196533] RAX: 00020000012d0000 RBX: ffff88010804aec8 RCX: ffff880118401b14
[10856.203852] RDX: 0000000000000048 RSI: 0000000000000000 RDI: ffff88010804aec8
[10856.211174] RBP: ffff880118401ac8 R08: 0000000000000001 R09: 0000000000000000
[10856.218496] R10: 0000000000000000 R11: 0000000000000006 R12: 0000000000000048
[10856.226026] R13: ffff880118401b14 R14: ffff88011752b258 R15: ffff88011752b258
[10856.233352] FS:  00007f26636d2740(0000) GS:ffff88011fc20000(0000) knlGS:0000000000000000
[10856.241626] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10856.247565] CR2: 00007f2663716e20 CR3: 00000000c7eb1000 CR4: 00000000000007e0
[10856.254889] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[10856.262215] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[10856.269542] Process dvbv5-zap (pid: 13606, threadinfo ffff880118400000, task ffff8800cd625d40)
[10856.278340] Stack:
[10856.280564]  ffff88011ffe8de8 0000000000000002 0000000000000000 ffff88011ffe9b00
[10856.288191]  ffff880118401b14 00ff88011ffe9b08 ffff880100000048 ffffffff8112a52a
[10856.295893]  0000000000000001 ffff88010804aec8 0000000000000048 ffff880118401b14
[10856.303521] Call Trace:
[10856.306182]  [<ffffffff8112a52a>] ? __alloc_pages_nodemask+0x15a/0x960
[10856.312912]  [<ffffffffa045a002>] em28xx_write_regs+0x32/0xa0 [em28xx]
[10856.319638]  [<ffffffffa045a221>] em28xx_write_reg+0x21/0x30 [em28xx]
[10856.326279]  [<ffffffffa045a2cc>] em28xx_gpio_set+0x9c/0x100 [em28xx]
[10856.332919]  [<ffffffffa045a3ac>] em28xx_set_mode+0x7c/0x80 [em28xx]
[10856.339472]  [<ffffffffa03ef032>] em28xx_dvb_bus_ctrl+0x32/0x40 [em28xx_dvb]

This is caused by commit c7a45e5b,
that added support for two I2C buses. A partial fix was applied
at 3de09fbb, but it doesn't cover
all cases, as the DVB core fills fe->dvb->priv with adapter->priv.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0

X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

commit 61ff5d69 "em28xx: improve em2710/em2820 distinction" missed the
le16_to_cpu conversion of the USB vendor ID.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit cd634f1b ("[media] v4l2: put VIDIOC_DBG_G_CHIP_NAME under
ADV_DEBUG") missed the initializer of radio_ioctl_ops:
drivers/media/usb/em28xx/em28xx-video.c:1830:2: error: unknown field 'vidioc_g_chip_info' specified in initializer
drivers/media/usb/em28xx/em28xx-video.c:1830:26: error: 'vidioc_g_chip_info' undeclared here (not in a function)
Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Map RC_MAP_REDDO to that device.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Chip id 18 is used by the em2710 and em2820.
The current code assumes that if the device is a camera, the chip is an em2710
and an em2820 otherwise.
But it turned out that the em2820 is also used in camera devices.
"Silvercrest 1.3 MPix" webcams for example are available with both chips.
Fortunately both variants are using different generic USD IDs which give us a
hint about the used chip.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The snapshot button support is currently broken, because module em28xx-rc is
loaded only if the device has remote control support.
Fix it by also loading this module if the device has a snapshot button.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

dvb->adapter.priv should also be set to the i2c bus since that's what
em28xx_tuner_callback expects.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This ioctl will be extended to return more information than just the name.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This
prevents abuse from both userspace and kernelspace (some bridge drivers
abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this
ioctl).
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx: fix typo in scale_to_size().
The second hscale should be vscale. This bug caused xawtv to fail because it
cannot find a workable image size.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some devices without DVB support (such as the "Terratec Grabby" and
"Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set
to 0 bytes for all alt settings.
Ignore these endpoints and avoid registering a DVB device node and loading the
DVB driver extension.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Streaming doesn't work with the EM2765 if bit 5 of the output format register
0x27 is set.
It's actually not clear if really has to be set for the other chips, but for
now let's keep it to avoid regressions and add a comment to the code.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The em25xx/em276x/em277x/em278x frame data format is different to the one used
by the em2710/em2750/em28xx chips.
With the recent cleanups and reorganization of the frame data processing code it
can be easily extended to support these devices.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm
for i2c communication with the sensor, which is connected to a second i2c bus.
We don't know yet how to find out which devices support/use it.
It's very likely used by all em25xx and em276x+ bridges.
Tests with other em28xx chips (em2820, em2882/em2883) show, that this
algorithm always succeeds there although no slave device is connected.
The algorithm likely also works for real i2c client devices (OV2640 uses SCCB),
because the Windows driver seems to use it for probing Samsung and Kodak
sensors.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for vidioc_g_chip_name, allowing AC97 to be implemented as a
second chip on the bridge with the name "ac97". v4l2-dbg can just match the
name with that string in order to detect a ac97-compliant set of registers.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NJonathan Corbet <corbet@lwn.net>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NAlexey Klimov <klimov.linux@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit aab3125c broke em28xx. I traced
this eventually to the change in what algo_data points to. This pointer
is also passed to em28xx_tuner_callback() through several hidden tuner
layers (yuck!) and that callback was not updated.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There's currently a bug on em28xx-i2c that makes it write the
wrong values to register 06, that controlls the I2C bus speed
and bus.

Fix it to change only the I2C bus flag.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is an hybrid board. However, for analog, it requires
a new driver for saa7136. So, for now, let's just add
support for Digital TV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It turned out that some devices return less bytes then requested via i2c when
ALL of the following 3 conditions are met:
- i2c bus B is used
- there was no attempt to write to the specified slave address before
- no device present at the specified slave address
With the current code, this triggers an -EIO error and prints a message to the
system log.
Because it can happen very often during device probing, it is better to ignore
this error and bail out silently after the follwing i2c transaction success
check with -ENODEV.

[mchehab@redhat.com: a small CodingStyle fix]
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The em28xx driver obtains the timestamps using function v4l2_get_timestamp(),
which produces a montonic timestamp.
Fixes the warnings appearing in the system log since commit 6aa69f99
"[media] vb2: Add support for non monotonic timestamps"
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>