The AHCI specification allows hardware to choose to revert to
single MSI mode when fewer messages are allocated than requested.
Yet, at least ICH10 chipset reverts to single MSI mode even when
enough messages are allocated in some cases (see below).

This update forces the driver to not rely on initialization of
multiple MSIs mode alone and always check if "MSI Revert to
Single Message" (MRSM) mode was enforced by the controller and
fallback to the single MSI mode in case it did.

That prevents a situation when the driver configured multiple
per-port IRQ handlers, but the controller sends all port's
interrupts to a single IRQ, which could easily screw up the
interrupt handling and lead to delays and possibly crashes.

The fix was tested on a 6-port controller that successfully
reverted to the single MSI mode:

00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller (prog-if 01 [AHCI 1.0])
	Subsystem: Super Micro Computer Inc Device 10a7
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 101
	I/O ports at f110 [size=8]
	I/O ports at f100 [size=4]
	I/O ports at f0f0 [size=8]
	I/O ports at f0e0 [size=4]
	I/O ports at f020 [size=32]
	Memory at fbf00000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
	Capabilities: [70] Power Management version 3
	Capabilities: [a8] SATA HBA v1.0
	Capabilities: [b0] PCI Advanced Features
	Kernel driver in use: ahci

With 6 ports just 8 MSI vectors should be enough, but the adapter
enforces the MRSM mode when less than 16 vectors are written to
the Multiple Messages Enable PCI register. I instigated MRSM mode
by forcing @nvec to 8 in ahci_init_interrupts().
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: NTejun Heo <tj@kernel.org>

System may crash in ahci_hw_interrupt() or ahci_thread_fn() when
accessing the interrupt status in a port's private_data if the port is
actually a DUMMY port.

00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller

<snip console output for linux-3.15-rc1>
[    9.352080] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x1 impl SATA mode
[    9.352084] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc
[    9.368155] Console: switching to colour frame buffer device 128x48
[    9.439759] mgag200 0000:11:00.0: fb0: mgadrmfb frame buffer device
[    9.446765] mgag200 0000:11:00.0: registered panic notifier
[    9.470166] scsi1 : ahci
[    9.479166] scsi2 : ahci
[    9.488172] scsi3 : ahci
[    9.497174] scsi4 : ahci
[    9.506175] scsi5 : ahci
[    9.515174] scsi6 : ahci
[    9.518181] ata1: SATA max UDMA/133 abar m2048@0x95c00000 port 0x95c00100 irq 91
[    9.526448] ata2: DUMMY
[    9.529182] ata3: DUMMY
[    9.531916] ata4: DUMMY
[    9.534650] ata5: DUMMY
[    9.537382] ata6: DUMMY
[    9.576196] [drm] Initialized mgag200 1.0.0 20110418 for 0000:11:00.0 on minor 0
[    9.845257] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    9.865161] ata1.00: ATAPI: Optiarc DVD RW AD-7580S, FX04, max UDMA/100
[    9.891407] ata1.00: configured for UDMA/100
[    9.900525] scsi 1:0:0:0: CD-ROM            Optiarc  DVD RW AD-7580S  FX04 PQ: 0 ANSI: 5
[   10.247399] iTCO_vendor_support: vendor-support=0
[   10.261572] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   10.269764] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[   10.301932] sd 0:2:0:0: [sda] 570310656 512-byte logical blocks: (291 GB/271 GiB)
[   10.317085] sd 0:2:0:0: [sda] Write Protect is off
[   10.328326] sd 0:2:0:0: [sda] Write cache: disabled, read cache: disabled, supports DPO and FUA
[   10.375452] BUG: unable to handle kernel NULL pointer dereference at 000000000000003c
[   10.384217] IP: [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci]
[   10.392101] PGD 0
[   10.394353] Oops: 0000 [#1] SMP
[   10.397978] Modules linked in: sr_mod(+) cdrom sd_mod iTCO_wdt crc_t10dif iTCO_vendor_support crct10dif_common ahci libahci libata lpc_ich mfd_core mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm drm i2c_core megaraid_sas dm_mirror dm_region_hash
dm_log dm_mod
[   10.426499] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.15.0-rc1 #1
[   10.433495] Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.S013.032920111005 03/29/2011
[   10.443886] task: ffffffff81906460 ti: ffffffff818f0000 task.ti: ffffffff818f0000
[   10.452239] RIP: 0010:[<ffffffffa0133df0>]  [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci]
[   10.462838] RSP: 0018:ffff880033c03d98  EFLAGS: 00010046
[   10.468767] RAX: 0000000000a400a4 RBX: ffff880029a6bc18 RCX: 00000000fffffffa
[   10.476731] RDX: 00000000000000a4 RSI: ffff880029bb0000 RDI: ffff880029a6bc18
[   10.484696] RBP: ffff880033c03dc8 R08: 0000000000000000 R09: ffff88002f800490
[   10.492661] R10: 0000000000000000 R11: 0000000000000005 R12: 0000000000000000
[   10.500625] R13: ffff880029a6bd98 R14: 0000000000000000 R15: ffffc90000194000
[   10.508590] FS:  0000000000000000(0000) GS:ffff880033c00000(0000) knlGS:0000000000000000
[   10.517623] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   10.524035] CR2: 000000000000003c CR3: 00000000328ff000 CR4: 00000000000007b0
[   10.531999] Stack:
[   10.534241]  0000000000000017 ffff880031ba7d00 000000000000005c ffff880031ba7d00
[   10.542535]  0000000000000000 000000000000005c ffff880033c03e10 ffffffff810c2a1e
[   10.550827]  ffff880031ae2900 000000008108fb4f ffff880031ae2900 ffff880031ae2984
[   10.559121] Call Trace:
[   10.561849]  <IRQ>
[   10.563994]  [<ffffffff810c2a1e>] handle_irq_event_percpu+0x3e/0x1a0
[   10.571309]  [<ffffffff810c2bbd>] handle_irq_event+0x3d/0x60
[   10.577631]  [<ffffffff810c4fdd>] try_one_irq.isra.6+0x8d/0xf0
[   10.584142]  [<ffffffff810c5313>] note_interrupt+0x173/0x1f0
[   10.590460]  [<ffffffff810c2a8e>] handle_irq_event_percpu+0xae/0x1a0
[   10.597554]  [<ffffffff810c2bbd>] handle_irq_event+0x3d/0x60
[   10.603872]  [<ffffffff810c5727>] handle_edge_irq+0x77/0x130
[   10.610199]  [<ffffffff81014b8f>] handle_irq+0xbf/0x150
[   10.616040]  [<ffffffff8109ff4e>] ? vtime_account_idle+0xe/0x50
[   10.622654]  [<ffffffff815fca1a>] ? atomic_notifier_call_chain+0x1a/0x20
[   10.630140]  [<ffffffff816038cf>] do_IRQ+0x4f/0xf0
[   10.635490]  [<ffffffff815f8aed>] common_interrupt+0x6d/0x6d
[   10.641805]  <EOI>
[   10.643950]  [<ffffffff8149ca9f>] ? cpuidle_enter_state+0x4f/0xc0
[   10.650972]  [<ffffffff8149ca98>] ? cpuidle_enter_state+0x48/0xc0
[   10.657775]  [<ffffffff8149cb47>] cpuidle_enter+0x17/0x20
[   10.663807]  [<ffffffff810b0070>] cpu_startup_entry+0x2c0/0x3d0
[   10.670423]  [<ffffffff815dfcc7>] rest_init+0x77/0x80
[   10.676065]  [<ffffffff81a60f47>] start_kernel+0x40f/0x41a
[   10.682190]  [<ffffffff81a60941>] ? repair_env_string+0x5c/0x5c
[   10.688799]  [<ffffffff81a60120>] ? early_idt_handlers+0x120/0x120
[   10.695699]  [<ffffffff81a605ee>] x86_64_start_reservations+0x2a/0x2c
[   10.702889]  [<ffffffff81a60733>] x86_64_start_kernel+0x143/0x152
[   10.709689] Code: a0 fc ff 85 c0 8b 4d d4 74 c3 48 8b 7b 08 89 ca 48 c7 c6 60 66 13 a0 31 c0 e8 9d 70 28 e1 8b 4d d4 eb aa 0f 1f 84 00 00 00 00 00 <45> 8b 64 24 3c 48 89 df e8 23 47 4c e1 41 83 fc 01 19 c0 48 83
[   10.731470] RIP  [<ffffffffa0133df0>] ahci_hw_interrupt+0x100/0x130 [libahci]
[   10.739441]  RSP <ffff880033c03d98>
[   10.743333] CR2: 000000000000003c
[   10.747032] ---[ end trace b6e82636970e2690 ]---
[   10.760190] Kernel panic - not syncing: Fatal exception in interrupt
[   10.767291] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)

Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-of-by: NDavid Milburn <dmilburn@redhat.com>
Fixes: 5ca72c4f ("AHCI: Support multiple MSIs")

Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a
special register to be poked before starting the DMA engine.

This register gets reset on an ahci_stop_engine call, so there is no other
place then ahci_start_engine where this poking can be done.

This commit allows drivers to override ahci_start_engine behavior for use by
the Allwinner AHCI driver (and potentially other drivers in the future).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands.  Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: NLevente Kurusa <levex@linux.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Cc: stable@vger.kernel.org

Commit 7b92b4f6 ("PCI/MSI: Remove pci_enable_msi_block_auto()")
introduced a regression: if multiple MSI initialization fails, the code
falls back to INTx rather than to single MSI.

Fixes: 7b92b4f6 ("PCI/MSI: Remove pci_enable_msi_block_auto()")
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NTejun Heo <tj@kernel.org>

pci_enable_msi_block() has been deprecated; use pci_enable_msi_range()
instead.

[bhelgaas: changelog]
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NTejun Heo <tj@kernel.org>

Commit 7b92b4f6 ("PCI/MSI: Remove pci_enable_msi_block_auto()")
introduced a regression: if multiple MSI initialization fails, the code
falls back to INTx rather than to single MSI.

Fixes: 7b92b4f6 ("PCI/MSI: Remove pci_enable_msi_block_auto()")
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NTejun Heo <tj@kernel.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Cc: linux-ide@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.

Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().

pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NTejun Heo <tj@kernel.org>

This patch adds support for the PCI ID provided by the Marvell 88SE9170
SATA controller.
Signed-off-by: NSimon Guinot <sguinot@lacie.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

The check for "combined mode" (which disables ahci support) on ICH6 is
done after the first use of AHCI BAR. But if ahci is not enabled AHCI
BAR is initialized to 0x00000000. (At least it is on the ICH6-M I tested
this on. If I understand the datasheet correctly it should also be on
ICH6R.) This apparently makes the call of
pcim_iomap_regions_request_all() return -EINVAL. And we end up with
    ahci: probe of 0000:00:1f.2 failed with error -22

(at warning level) in the logs.

So check for "combined mode" before calling
pcim_iomap_regions_request_all().
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch marks the function ahci_init_interrupts() as static in ahci.c
because it is not used outside this file.

Thus, it also eliminates the following warning in ahci.c:
drivers/ata/ahci.c:1099:5: warning: no previous prototype for ‘ahci_init_interrupts’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>

Tested with a DAWICONTROL DC-624e on 3.10.10
Signed-off-by: NSamir Benmendil <samir.benmendil@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NLevente Kurusa <levex@linux.com>
Cc: stable@vger.kernel.org

Apple's BIOS emulation forcibly disables MCP89 AHCI, eg. on Macbook7,1.
We can re-enable it, replacing the previous workaround of using
ata_generic.

tj: whitespace adjustments, dropped inline from is_mcp89_apple()
Signed-off-by: NJames Laird <jhl@mafipulation.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch adds the AHCI-mode SATA Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Change "raw" printk() call to dev_info() to provide a better
message to userspace so it can properly identify the device
and not just have to guess.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Add a new port flag, ATA_FLAG_FPDMA_AUX, used to indicate
support for transmission of the H2D FIS 'auxiliary' field.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

commit b29900e6 (AHCI: Make distinct names for ports in /proc/interrupts)
introuded a regression, which resulted Null pointer dereference for achi
host with dummy ports. For ahci ports, when the port is dummy port, its
private_data will be NULL, as ata_dummy_port_ops doesn't support ->port_start.

changes in v2: use pp to check dummy ports, update comments
Reported-and-tested-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NXiaotian Feng <xtfeng@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

ahci_hardreset() and ahci_p5wdh_hardreset() use bare numbers for the
BSY bit of the ATA status register, despite it's #define'd in
<linux/ata.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

This patch adds the AHCI-mode SATA DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

To add AMD CZ SATA controller device ID of IDE mode.

[bhelgaas: drop pci_ids.h update]
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev.  This is a purely cosmetic change.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

A third possible PCI ID, as personally observed, and found in the
pci.ids list.
Signed-off-by: NGeorge Spelvin <linux@horizon.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.
Reported-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Jeff moved on to a greener pasture.

 s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>

With the 0x1b4b vendor ID #define in place, convert hard-coded ID
values.
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds the RAID-mode SATA Device IDs for the Intel Wellsburg PCH
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the AHCI-mode SATA Device IDs for the Intel Wellsburg PCH
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the AHCI and RAID-mode SATA DeviceIDs for the Intel Avoton SOC.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Take advantage of multiple MSIs implementation on x86 - on
systems with IRQ remapping AHCI ports not only get assigned
separate MSI vectors - but also separate IRQs. As result,
interrupts generated by different ports could be serviced on
different CPUs rather than on a single one.

In cases when number of allocated MSIs is less than requested
the Sharing Last MSI mode does not get used, no matter
implemented in hardware or not. Instead, the driver assumes the
advantage of multiple MSIs is negated and falls back to the
single MSI mode as if MRSM bit was set (some Intel chips
implement this strategy anyway - MRSM bit gets set even if the
number of allocated MSIs exceeds the number of implemented ports).
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/15bf7ee314dd55f21ec7d2a01c47613cd8190a7c.1353324359.git.agordeev@redhat.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

Silicon does not support standard AHCI BAR assignment.  Add
vendor/device exception to force BAR 2.
Signed-off-by: NHugh Daschbach <hugh.daschbach@enmotus.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

They don't always appear as AHCI class devices but instead as IDE class.

Based on an initial patch by Hiroaki Nito

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42804Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: The Stables <stable@vger.kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The JMicron JMB362 controller supports AHCI only, but some revisions
use the IDE class code.  These need to be matched by device ID.

These additions have apparently been included by QNAP in their NAS
devices using these controllers.

References: http://bugs.debian.org/634180Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the AHCI-mode SATA Device IDs for the Intel Lynx Point-LP PCH
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fixed coding style issues related to braces found
by checkpatch.pl in drivers/ata/ahci.c
Signed-off-by: NJeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch converts the drivers in drivers/ata/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Mark Lord <kernel@teksavvy.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Like e65cc194 (ahci: Enable SB600 64bit
DMA on MSI K9A2 Platinum) and 3c4aa91f
(ahci: Enable SB600 64bit DMA on Asus M3A), this patch enables 64bit DMA
for the AHCI SATA controller of another board that has the SB600
southbridge.

In this case though we're enabling 64bit DMA for another MSI motherboard,
the K9AGM2 or MS-7327. It is new enough that all of the BIOS releases
since the initial release (1.0 from 2007-02-09) work correctly with 64bit
DMA enabled.
Signed-off-by: NMark Nelson <mdnelson8@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The Marvell 88SE9172 SATA controller (PCI ID 1b4b 917a) already worked
once it was detected, but was missing an ahci_pci_tbl entry.

Boot tested on a Gigabyte Z68X-UD3H-B3 motherboard.
Signed-off-by: NMatt Johnson <johnso87@illinois.edu>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We will need this macro in both ahci.c and ahci_platform.c, so just move it
to the header.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org