We always call iwl_nvm_init() with read_nvm_from_nic == true, so this
argument is useless.  Remove it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have some of the SAR dummy functions when ACPI is not set declared
in mvm.h and some declared in fw.c.  Group them all together in fw.c
for consistency and to avoid static/non-static issues.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to differentiate an INIT that ended early because of
RFKILL from one that succeded.  Additionally, if INIT fails later,
during calibration, due to RFKILL, we can just return success and
continue as if we were already in RFKILL to start with.

Remove this unnecessary differentiation and do some other small
clean-ups while at it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case there is no value received from BIOS
for cTDP budget, the default should be 2000 mWatt.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Getting the NVM data in a000 devices should be shared
across operation mode.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.

Fixes: 503ab8c5 ("iwlwifi: Add 8000 HW family support")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We should free 'wgds.pointer' here as done a few lines above in another
error handling path.
It was allocated within 'acpi_evaluate_object()'.

Fixes: c52030a01ccc ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Refactor the shared memory command parsing into common code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This structure represents V2, V1 has the three last fields missing.
Rename it to be more accurate.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.

While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Convert ucode_loaded to a status bit called FIRMWARE_RUNNING.
This will make it easier to clear this earlier, to avoid any
spurious accesses while shutting down, for example through
debugfs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add two new device families to differentiate them from 8000.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case an assert happens on init flow, the current
driver powers down the NIC, except if iwlmvm modparam
init_dbg=1, and only on very specific flows.

Extend this capability to cover most failure cases
by keeping track of what init configurations have been
completed. This way, we can allow NOT powering down
the NIC, while making sure that when the driver is
removed we don't try to free resources that haven't
been allocated. (This can result in a kernel panic.)
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Instead of using a union and hard-coding the size difference,
declare both command structs properly, use a union on the
stack to build them and the right sizeof() for the size.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add configuration for allowing driver's nvm parsing and
bypassing the new host command, for debugging.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This API replaces the complex NVM parsing of the iwlwifi module.
Instead, we get all needed data from firmware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In iwl_mvm_sar_get_ewrd_table() In case of a BIOS bug, n_profiles
might be 0 thus we need to return an error value.  Found by Klocwork.
Signed-off-by: NSharon Dvir <sharon.dvir@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to have iwl_run_unified_mvm_ucode() be exposed
to other parts of the code since the logic to pick it over the
normal code in iwl_run_init_mvm_ucode() can just be done in
that function itself.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we load firmware in extended mode (as we do by default for
now) driver should send a command what kind of commands ucode
should stop and wait for before proceeding with phy calibrations.
Support this command. Currently we only do NVM access - so mark
this bit only.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

To utilize the maximum allowed tx power, an additional table was added
to the BIOS. The table consists of up to seven different regions
(currently only three are in use). Each region contains per band:
1. Maximum allowed tx power on the band.
2. Tx power offset for chain A.
3. Tx power offset for chain B.
On init flow driver reads this table by means of ACPI and
passes it to the firmware with GEO_TX_POWER_LIMIT cmd.
The firmware will use this table to enhance tx power with
the offset in the relevant table as well as verifying it does not
violate the maximum allowed tx power.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

API was changed once more to support 2 LMACs.
Adapt to change while preserving current functionality.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Not only that this write is not needed (as FW does this
itself), on newer HW this register is write protected
so trying to write there will cause problems.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Dynamic SAR allows changing TX power limits at runtime to comply with
SAR regulations on multiple form factors (e.g. tablet vs. clamshell
mode).  To support this, a new table was added to ACPI, which is
called Extended Wireless Regulatory Descriptor (EWRD).  This table
allows OEMs to define different TX power profiles for each form-factor
or usage mode.

Read this new table and store it in our SAR profiles table, in
preparation for Dynamic SAR support.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For dynamic SAR, we will need to select the current profile from
different places.  In preparation for that, spin the profile selection
code out of iwl_mvm_sar_init().
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We are adding support for dynamic TX power tables for SAR (specific
absorption rate) compliance.  Currently, we only support a single
(static) TX power table, which is read from ACPI, and use it
statically.

To prepare for more tables that can be switched dynamically, refactor
the SAR init flow to allow reusage and add the current static table as
a single entry in an array of tables.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Firmware isn't configuring multi RX queue hardware yet in
the self init mode.
Disable it for now until we have an API that enables it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Addresses were changed for a000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Now that transport inits the paging in the context info -
remove the call in mvm.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case of a MFUART assert, get a notification from the fw
that consists of the assert id and debug data.

The notification may be divided to multiple chunks, depending
on the size of the debug data sent to the driver, which would
be up to 1KB.

Get the notification, and if the debug info flag is enabled,
print the debug data to the dmesg.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Divide a mfuart related print so it won't exceed the allowed
MAX_MSG_LEN (110 bytes) per print.

Fixes: 19f63c53 ("iwlwifi: mvm: support v2 of mfuart load notification")
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>