Hardware has a limited number of pools available (64). Previously, no
checks were in place to limit the number of accelerated macvlan devices
based on the number of pools. Normally this would be ok, because there
was already a limit for these well below the number of available pools.
However, SR-IOV uses the very same pools. Therefor, we need to ensure
that the total number of pools (number of VFs plus the number of non-VF
pools in use for accelerated macvlans) does not exceed the number of
pools available in hardware.

This patch resolves a kernel NULL pointer dereference caused by the following commands:

$modprobe ixgbe max_vfs=63

$ethtool -K eth2 l2-fwd-offload on

$ip link add link eth2 macvlan0 type macvlan

$ip link set dev macvlan0 up

[  992.950080] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056
[  992.951109] IP: [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.951684] PGD 22a80e067 PUD 232e9b067 PMD 0
[  992.952389] Oops: 0000 [#1] SMP
[  992.953014] Modules linked in: nfsd lockd nfs_acl exportfs auth_rpcgss oid_registry sunrpc bridge stp llc vhost_net macvtap macvlan vhost tun kvm_intel kvm ioatdma ixgbe mdio igb dca
[  992.956042] CPU: 2 PID: 11928 Comm: ifconfig Not tainted 3.16.0-rc6-net-next-07-29-2014-FCoE+ #1
[  992.956915] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014
[  992.957791] task: ffff8804341c0000 ti: ffff8801d7dc8000 task.ti: ffff8801d7dc8000
[  992.958660] RIP: 0010:[<ffffffffa003b71e>]  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.959613] RSP: 0018:ffff8801d7dcbbb8  EFLAGS: 00010286
[  992.960093] RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000001
[  992.960575] RDX: ffff880232eb7000 RSI: 0000000000000000 RDI: ffff88022dc05800
[  992.961059] RBP: ffff8801d7dcbbd8 R08: 0000000000000000 R09: 0000000000000000
[  992.961541] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88022ec20980
[  992.962023] R13: ffff880232eb7000 R14: 0000000000000001 R15: 0000000000000001
[  992.962508] FS:  00007fab264887a0(0000) GS:ffff880237640000(0000) knlGS:0000000000000000
[  992.963378] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  992.963858] CR2: 0000000000000056 CR3: 000000022a939000 CR4: 00000000001427e0
[  992.964340] Stack:
[  992.964806]  ffff88022ec28840 ffff88022ec20980 ffff88022dc05800 ffff880232eb7000
[  992.965976]  ffff8801d7dcbc28 ffffffffa003bae8 ffff8801d7dcbbe8 0000000000000400
[  992.967147]  000000000000000d ffff88022ec20980 ffff88022ec20000 ffff88022dc05800
[  992.968319] Call Trace:
[  992.968795]  [<ffffffffa003bae8>] ixgbe_fwd_ring_up+0x88/0x280 [ixgbe]
[  992.969284]  [<ffffffffa0041d83>] ixgbe_fwd_add+0x173/0x220 [ixgbe]
[  992.969767]  [<ffffffffa015056c>] macvlan_open+0x1bc/0x230 [macvlan]
[  992.970256]  [<ffffffff816b8de7>] __dev_open+0xd7/0x150
[  992.970735]  [<ffffffff816b8bd7>] __dev_change_flags+0xa7/0x170
[  992.971220]  [<ffffffff816b8ccb>] dev_change_flags+0x2b/0x70
[  992.971703]  [<ffffffff817471b2>] devinet_ioctl+0x602/0x6d0
[  992.972184]  [<ffffffff81748168>] inet_ioctl+0x78/0x90
[  992.972666]  [<ffffffff816a143b>] sock_do_ioctl+0x2b/0x70
[  992.973146]  [<ffffffff816a14ed>] sock_ioctl+0x6d/0x260
[  992.973627]  [<ffffffff811ad3b4>] do_vfs_ioctl+0x84/0x540
[  992.974109]  [<ffffffff811a4c81>] ? final_putname+0x21/0x50
[  992.974593]  [<ffffffff818725d5>] ? sysret_check+0x22/0x5d
[  992.975073]  [<ffffffff811ad901>] SyS_ioctl+0x91/0xa0
[  992.975550]  [<ffffffff818725a9>] system_call_fastpath+0x16/0x1b
[  992.976026] Code: ff 66 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 20 48 89 5d e8 4c 89 65 f0 48 89 f3 4c 89 6d f8 4c 8b a7 08 02 00 00 <44> 0f b6 6e 56 44 03 af 14 02 00 00 4c 89 e7 e8 5e f2 ff ff be
[  992.982261] RIP  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.983212]  RSP <ffff8801d7dcbbb8>
[  992.983681] CR2: 0000000000000056
[  992.984248] ---[ end trace 9f54802b5cc3638b ]---

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we previously called ixgbe_set_num_queues just prior to attempting
to set our interrupt scheme, it may be non obvious why we have to call
it again inside the function. Add a comment which helps make it more
obvious that we are resetting features based on the fact that we do not
have MSI-X enabled, and cannot use the previous settings.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VFLINKS.LINKUP bit tends to flap when a DA or SFP+ cable is disconnected.
It can take up to 500 usecs for the LINKUP bit to be correct.

This patch resolves the issue by introducing a delay for 82599 VFs of at
least 500 usecs to make sure the VFLINKS value is correct.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe initiates a reset of the interface on link loss with pending Tx work
in order to clear the rings.

This patch extends the pending Tx work check to the VF interfaces with the
same purpose.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the behavior for FDB handling is consistent
between both the SR-IOV and non-SR-IOV cases.  The main change here is that we
perform bounds checking on the number of SR-IOV addresses regardless of if
SR-IOV is enabled or not as we can only support a certain number of addresses
in the hardware.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is global funcion pci_vfs_assigned(), so use it instead of composing
local one.
Signed-off-by: NEthan Zhao <ethan.kernel@gmail.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e version to 1.0.11 and i40evf version to 1.0.5.

Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>

This fixes the panic under traffic load when resetting.  This issue
could also show up if/whenever there is a Tx-timeout.

Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We shouldn't restart Admin queue subtask if PF reset fails since we do
not have the AQ setup at that point. This patch makes sure we disable AQ
clean subtask when PF reset fails.

This will resolve an occasional kernel panic when PF reset fails for
some reason.

Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is un-necessarily printing a warning that is only marginally
useful to the user.  Make the warning only print if extended driver
string printing is enabled, other messages related to a reset event
will still continue to print.

Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we don't seem to be getting an LSE telling us link is going down
during set_phy_config (but we do get an LSE telling us we are coming
back up), fake one for the OS and tell them link is going down. Also
do an atomic restart no matter what because there are times the user
may want to end with link up even if they started with link down (like
if they accidentally set it to a speed that can't link and are trying to
fix it).

Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.

Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.

Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow the user to change auto-negotiation and speed settings if
link is down.

Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that fw has implemented dual speed module support, we can add ours.
Also, add the phy type for 1G LR/SR and set its media type to fiber.
Lastly, instead of a WARN_ON if the phy type is not recognized just print
a warning.

Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate.  This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused 'dev' variable from arc_emac_remove(), since it's
not being used any more.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary double parenthesis around if statement.
Signed-off-by: NDavid Wood <devel@dtwood.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the BE3 super-nic profile, the max_tx_qs value can vary for each function.
So the driver needs to query this value from FW instead of using the
pre-defined constant BE3_MAX_TX_QS.
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the for() loop that traverses all the TX queues on an EQ
with the macro for_all_tx_queues_on_eq(). With this expalnatory
name, the one line comment is not required anymore.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enforcing a budget on the TX completion processing in NAPI doesn't
benefit performance in anyway. Just get rid of it.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch defines a new macro BE_MAX_MTU to make the code in be_change_mtu()
more readable.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In cases where there is no extra code to handle an error, this patch replaces
gotos with a direct return statement.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log messages in the Lancer FW download path have issues such as:
- a single message spanning multiple lines
- the success message is logged even in failure cases
- status codes are already logged in the FW cmd routines
This patch fixes these issues.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a dma_mapping_error counter to count the number of packets dropped
due to DMA mapping errors.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW reports TX completion errors in TX completion. This patch adds these
counters to ethtool statistics.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AMAP_GET/SET_BITS() macro calls take structure name as a parameter
and hence are long and span more than one line. Replace these calls
with a wrapper macros for RX/Tx compls and TX wrb. This results in fewer
lines and more readable code in be_main.c
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following log messages to help debugging
failure cases:
1) log FW version number: this is useful when driver initialization
fails and the FW version number cannot be queried via ethtool
2) per function resource limits for BEx chips: these values are
currently being printed only for Skyhawk and Lancer
3) PCI BAR mapping failure
4) function_mode/caps queried from FW: this helps catch any FW bugs
that could advertise wrong capabilities to the driver
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable "rx_buf_sz" is used by both tx and rx buffers. Replace
it with "agg_buf_sz".
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/phy/mdio-bcm-unimac.c:195:37-38: unimac_mdio_ids is not NULL
terminated at line 195

Make sure of_device_id tables are NULL terminated
Generated by: scripts/coccinelle/misc/of_table.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for slave_changelink to the bonding and uses it
to give the ability to change the queue_id of the enslaved devices via
netlink. It sets slave_maxtype and uses bond_changelink as a prototype for
bond_slave_changelink.
Example/test command after the iproute2 patch:
 ip link set eth0 type bond_slave queue_id 10

CC: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Suggested-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Broadcom tags are enabled, e.g: when interfaced to an Ethernet
switch, make sure that we tell the RXCHK engine that it should be
expecting a 4-bytes Broadcom tag after the Ethernet MAC Source Address.

Use netdev_uses_dsa() to check for that condition since that will tell
us if a switch is attached to our network interface.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set correct bit for packed description.

Introduced in e42780b6
    bnx2x: Utilize FW 7.10.51
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes incorrectly defined struct in FW HSI for BE platform.
Affects tunneling, tx-switching and anti-spoofing.

Introduced in e42780b6
    bnx2x: Utilize FW 7.10.51
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because the Tx has the features of stopping queue and aggregation,
We don't need many tx buffers. Change the tx number from 10 to 4
to reduce the usage of the memory. This could save 16K * 6 bytes
memory.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For now it will always be false.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That way we don't have to audit every call site to make sure it is
doing this properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>