Some devices, especially those with high speed control interfaces, require
padding between the register and the data. Support this in the regmap API
by providing a pad_bits configuration parameter.

Only devices with integer byte counts are supported.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the initialization regcache related fields of the regmap struct to
regcache_init. This allows us to keep regmap and regcache code better
separated.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There should be no situation where it offers any advantage over rbtree
and there are no current users so remove the code for simplicity.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move the initialization regcache related fields of the regmap struct to
regcache_init. This allows us to keep regmap and regcache code better
separated.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow drivers to optimise out the register cache sync if they didn't need
to do one. If the hardware is desynced from the register cache (by power
loss for example) then the driver should call regcache_mark_dirty() to
let the core know about this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for LZO compression when storing the register
cache.

For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB.  There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable.  These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst.  Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for the rbtree cache compression type.

Each rbnode manages a variable length block of registers.  There can be no
two nodes with overlapping blocks.  Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.

The reasoning behind the construction of this rbtree is simple.  In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the regcache core.  For each register value that is non-zero we
insert it in the rbtree.  In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add.  If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.

There are various optimizations across the implementation to speed up lookups
by caching the most recently used rbnode.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is the simplest form of a cache available in regcache.  Any
registers whose default value is 0 are ignored.  If any of those
registers are modified in the future, they will be placed in the
cache on demand.  The cache layout is essentially using the provided
register defaults by the regcache core directly and does not re-map
it to another representation.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch introduces caching support for regmap.  The regcache API
has evolved essentially out of ASoC soc-cache so most of the actual
caching types (except LZO) have been tested in the past.

The purpose of regcache is to optimize in time and space the handling
of register caches.  Time optimization is achieved by not having to go
over a slow bus like I2C to read the value of a register, instead it is
cached locally in memory and can be retrieved faster.  Regarding space
optimization, some of the cache types are better at packing the caches,
for e.g. the rbtree and the LZO caches.  By doing this the sacrifice in
time still wins over doing I2C transactions.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Make the debugfs stubs static inline to avoid future compilation issues due to
duplicated symbols when CONFIG_DEBUG_FS=n once internal.h is included by
multiple source files.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some buses like SPI have no standard notation of read or write operations.
The general scheme here is to set or clear specific bits in the register
address to indicate whether the operation is a read or write. We already
support having a read flag mask per bus, but as there is no standard
the bits which need to be set or cleared differ between devices and vendors,
thus we need a mechanism to specify them per device.

This patch adds two new entries to the regmap_config struct, read_flag_mask and
write_flag_mask. These will be or'ed onto the top byte when doing a read or
write operation. If both masks are empty the device will fallback to the
regmap_bus masks.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We're going to be using these in quite a few places so factor out the
readable/writable/volatile/precious checks.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Copy over the read parts of the ASoC debugfs implementation into regmap,
allowing users to see what the register values the device has are at
runtime. The implementation, especially the support for seeking, is
mostly due to Dimitris Papastamos' work in ASoC.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allowing the implementation to be multi-file.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>