The POWER8NVL chip has two CAPI ports.  Configure the PSL to route
data to the port corresponding to the CAPP unit.
Signed-off-by: NPhilippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NPhilippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch assigns numbers to OPAL_MSG macros of enum opal_msg_type
to prevent accidental insertion of any new value in between and thus
break OPAL API. This is also helpful while backporting mainline kernel
changes to distros which run downlevel kernel and thus don't have all
OPAL messages defined, avoiding unnecessary bugs due to enum values
order mismatch.
Signed-off-by: NVipin K Parashar <vipin@linux.vnet.ibm.com>
Acked-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We'd like folks working on drivers for powerpc to also Cc linuxppc-dev,
so we can be aware of what's going on in drivers and/or review the
changes.

So add patterns to the powerpc MAINTAINERS section to catch some of the
drivers we're interested in.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If CONFIG_HIBERNATION and CONFIG_PPC_BOOK3S_64 are set, code in
arch/powerpc/kernel/swsusp_amd64.S which uses the tlbia macro is enabled.
tlbia in turn uses tlbie, an instruction which takes more than one
operand in newer versions of POWER.  As such, the kernel fails to build
due to the assembler complaining about missing operands.

This can be worked around by assembling the instruction as in POWER4.
This fixes the build breakage caused by enabling CONFIG_HIBERNATION.
Hibernation is currently only tested on G5 PowerMacs, which should be
unaffected by this change.  For other platforms it may now build,
whether or not it works is a different story.
Signed-off-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently on PPC64 changing kernel pagesize from 4K to 64K leaves
FORCE_MAX_ZONEORDER set to 13 - which produces a compile error.

The error occurs because of the following constraint (from
include/linux/mmzone.h) being violated:

	MAX_ORDER -1 + PAGESHIFT <= SECTION_SIZE_BITS.

Expanding this out, we get:

	FORCE_MAX_ZONEBITS <= 25 - PAGESHIFT,

which requires, for a 64K page, FORCE_MAX_ZONEBITS <= 9. Thus set max
value of FORCE_MAX_ZONEORDER for 64K pages to 9, and 4K pages to 13.

Also, check the minimum value:
In include/linux/huge_mm.h, we have the constraint HPAGE_PMD_ORDER <
MAX_ORDER which expands out to:

	PTE_INDEX_SIZE < FORCE_MAX_ZONEORDER.

PTE_INDEX_SIZE is:
	9 (4k hash or no hash 4K pgtable) or
	8 (64K hash or no hash 64K pgtable).
Thus a min value of 8 for 64K pages and 9 for 4K pages is reasonable.

So, update the range of FORCE_MAX_ZONEORDER from 9-64 to 8-9 for 64K pages
and from 13-64 to 9-13 for 4K pages.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Reviewed-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The Kconfig for this driver is currently:

config CPU_FREQ_CBE_PMI
    bool "CBE frequency scaling using PMI interface"

...meaning that it currently is not being built as a module by
anyone.  Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The Makefile/Kconfig currently controlling compilation of this code is:

obj-$(CONFIG_PPC64)             += setup_64.o sys_ppc32.o \
                                   signal_64.o ptrace32.o \
                                   paca.o nvram_64.o firmware.o

arch/powerpc/platforms/Kconfig.cputype:config PPC64
arch/powerpc/platforms/Kconfig.cputype: bool "64-bit kernel"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't replace module.h with init.h since the file already has that.

We delete the MODULE_LICENSE tag since that information is already
contained at the top of the file in the comments.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The Kconfig currently controlling compilation of this code is:

arch/powerpc/platforms/cell/Kconfig:config SPU_BASE
arch/powerpc/platforms/cell/Kconfig:    bool

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

IBM online documentation for EEH uses "extended error handling" and
"enhanced error handling" to refer to the same thing, in different
places.  The only place mentioning it as "enhanced error handling" in the
kernel is the MAINTAINERS file, and it's "extended" in some documentation.

IBM originally defined EEH as "enhanced error handling", so standardise
all mentions of EEH to use that term.
Signed-off-by: NRussell Currey <ruscur@russell.cc>
Acked-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

generic_memcpy() is only called from copy_32.S, so there's no reason for
it to be global.
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This has been unused since ~2004, remove it.
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We have a bunch of SLB related code in the tree which is there to handle
dynamic VSIDs - but currently it's all disabled at compile time. The
comments say "Keep that around for when we re-implement dynamic VSIDs".

But that was over 10 years ago (commit 3c726f8d ("[PATCH] ppc64:
support 64k pages")). The chance that it would still work unchanged is
minimal, and in the meantime it's confusing to folks browsing/grepping
the code. If we ever want to re-instate it, it's in the git history.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NBalbir Singh <bsingharora@gmail.com>

The HMI code knows about three types of errors: CORE, NX and UNKNOWN.
If OPAL were to add a new type, it would not be handled at all since
there is no fallback case.  Instead of explicitly checking for UNKNOWN,
treat any checkstop type without a handler as unknown.
Signed-off-by: NRussell Currey <ruscur@russell.cc>
Reviewed-by: NDaniel Axtens <dja@axtens.net>
Reviewed-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Function cxl_get_phys_dev() was removed from the kernel API by a
previous patch, but it's actually dead code. Remove it.
Signed-off-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: NIan Munsie <imunsie@au1.ibm.com>
Reviewed-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The associativity array index specified for a LMB in the device tree,
/ibm,dynamic-reconfiguration-memory/ibm,dynamic-memory, needs to be updated
prior to DLPAR adding a LMB and after DLPAR removing a LMB.

Without doing this step in the DLPAR add process a LMB could be configured
with the incorrect affinity. For a LMB that was not present at boot the
affinity index is set to 0xffffffff, which defaults to adding the LMB to
the first online node since the index is not a valid value. Or, the
affinity index could contain a stale value if the LMB was present at boot
but later DLPAR removed and is being DLPAR added back to the system.

This patch adds a step in the DLPAR add flow to look up the associativity
index for a LMB prior to adding a LMB and setting the associativity to
0xffffffff when a LMB is removed.

This patch also modifies the DLPAR add/remove flow to no longer do a single
update of the device tree property after all of the requested DLPAR
operations are complete and now does a property update during the add
or remove of each LMB.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Re-factor dlpar_lmb_add() routine by moving the validation of the lmb
flags and the acquireing of the DRC to a wrapper around the work to add
the memory to the system. This is done to make handling of errors
during the addition of the memory easier and to facilitate the upcoming
addition of updating the lmb's affinity prior to adding the memory.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Pull ARM fixes from Russell King:
 "A couple of small fixes, and wiring up the new syscalls which appeared
  during the merge window"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8550/1: protect idiv patching against undefined gcc behavior
  ARM: wire up preadv2 and pwritev2 syscalls
  ARM: SMP enable of cache maintanence broadcast

Pull MMC fixes from Ulf Hansson:
 "Here are a couple of mmc fixes intended for v4.6 rc3:

  MMC host:
   - sdhci: Fix regression setting power on Trats2 board
   - sdhci-pci: Add support and PCI IDs for more Broxton host controllers"

* tag 'mmc-v4.6-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pci: Add support and PCI IDs for more Broxton host controllers
  mmc: sdhci: Fix regression setting power on Trats2 board

Pull i2c fixes from Wolfram Sang:
 "Some bugfixes from I2C:

   - fix a uevent triggered boot problem by removing a useless debug
     print

   - fix sysfs-attributes of the new i2c-demux-pinctrl driver to follow
     standard kernel behaviour

   - fix a potential division-by-zero error (needed two takes)"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: jz4780: really prevent potential division by zero
  Revert "i2c: jz4780: prevent potential division by zero"
  i2c: jz4780: prevent potential division by zero
  i2c: mux: demux-pinctrl: Update docs to new sysfs-attributes
  i2c: mux: demux-pinctrl: Clean up sysfs attributes
  i2c: prevent endless uevent loop with CONFIG_I2C_DEBUG_CORE

This reverts commit 1028b55b.

It's broken: it makes ext4 return an error at an invalid point, causing
the readdir wrappers to write the the position of the last successful
directory entry into the position field, which means that the next
readdir will now return that last successful entry _again_.

You can only return fatal errors (that terminate the readdir directory
walk) from within the filesystem readdir functions, the "normal" errors
(that happen when the readdir buffer fills up, for example) happen in
the iterorator where we know the position of the actual failing entry.

I do have a very different patch that does the "signal_pending()"
handling inside the iterator function where it is allowable, but while
that one passes all the sanity checks, I screwed up something like four
times while emailing it out, so I'm not going to commit it today.

So my track record is not good enough, and the stars will have to align
better before that one gets committed.  And it would be good to get some
review too, of course, since celestial alignments are always an iffy
debugging model.

IOW, let's just revert the commit that caused the problem for now.
Reported-by: NGreg Thelen <gthelen@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull parisc fixes from Helge Deller:
 "Since commit 0de79858 ("parisc: Use generic extable search and
  sort routines") module loading is boken on parisc, because the parisc
  module loader wasn't prepared for the new R_PARISC_PCREL32 relocations.

  In addition, due to that breakage, Mikulas Patocka noticed that
  handling exceptions from modules probably never worked on parisc.  It
  was just masked by the fact that exceptions from modules don't happen
  during normal use.

  This patch series fixes those issues and survives the tests of the
  lib/test_user_copy kernel module test.  Some patches are tagged for
  stable"

* 'parisc-4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Update comment regarding relative extable support
  parisc: Unbreak handling exceptions from kernel modules
  parisc: Fix kernel crash with reversed copy_from_user()
  parisc: Avoid function pointers for kernel exception routines
  parisc: Handle R_PARISC_PCREL32 relocations in kernel modules

Pull libnvdimm fixes from Dan Williams:
 "Three fixes, the first two are tagged for -stable:

   - The ndctl utility/library gained expanded unit tests illuminating a
     long standing bug in the libnvdimm SMART data retrieval
     implementation.

     It has been broken since its initial implementation, now fixed.

   - Another one line fix for the detection of stale info blocks.

     Without this change userspace can get into a situation where it is
     unable to reconfigure a namespace.

   - Fix the badblock initialization path in the presence of the new (in
     v4.6-rc1) section alignment workarounds.

     Without this change badblocks will be reported at the wrong offset.

  These have received a build success report from the kbuild robot and
  have appeared in -next with no reported issues"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
  libnvdimm, pfn: fix uuid validation
  libnvdimm: fix smart data retrieval

Pull GPIO fixes from Linus Walleij:
 "Here is a set of four GPIO fixes.  The two fixes to the core are
  serious as they are regressing minor architectures.

  Core fixes:

   - Defer GPIO device setup until after gpiolib is initialized.

     It turns out that a few very tightly integrated GPIO platform
     drivers initialize so early (befor core_initcall()) so that the
     gpiolib isn't even initialized itself.  That limits what the
     library can do, and we cannot reference uninitialized fields until
     later.

     Defer some of the initialization until right after the gpiolib is
     initialized in these (rare) cases.

   - As a consequence: do not use devm_* resources when allocating the
     states in the initial set-up of the gpiochip.

  Driver fixes:

   - In ACPI retrieveal: ignore GpioInt when looking for output GPIOs.

   - Fix legacy builds on the PXA without a backing pin controller.

   - Use correct datatype on pca953x register writes"

* tag 'gpio-v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: pca953x: Use correct u16 value for register word write
  gpiolib: Defer gpio device setup until after gpiolib initialization
  gpiolib: Do not use devm functions when registering gpio chip
  gpio: pxa: fix legacy non pinctrl aware builds
  gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*

Pull tty fixes from Greg KH:
 "Here are two tty fixes for issues found.

  One was due to a merge error in 4.6-rc1, and the other a regression
  fix for UML consoles that broke in 4.6-rc1.

  Both have been in linux-next for a while"

* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix merge of "tty: Refactor tty_open()"
  tty: Fix UML console breakage

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.6-rc3.

  Nothing major, the normal USB gadget fixes and usb-serial driver ids,
  along with some other fixes mixed in.  All except the USB serial ids
  have been tested in linux-next, the id additions should be fine as
  they are 'trivial'"

* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: option: add "D-Link DWM-221 B1" device id
  USB: serial: cp210x: Adding GE Healthcare Device ID
  USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
  usb: dwc3: keystone: drop dma_mask configuration
  usb: gadget: udc-core: remove manual dma configuration
  usb: dwc3: pci: add ID for one more Intel Broxton platform
  usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
  usb: dwc2: do not override forced dr_mode in gadget setup
  usb: gadget: f_midi: unlock on error
  USB: digi_acceleport: do sanity checking for the number of ports
  USB: cypress_m8: add endpoint sanity check
  USB: mct_u232: add sanity checking in probe
  usb: fix regression in SuperSpeed endpoint descriptor parsing
  USB: usbip: fix potential out-of-bounds write
  usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
  usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
  usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
  usb: phy: qcom-8x16: fix regulator API abuse
  usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
  usb: gadget: composite: Access SSP Dev Cap fields properly
  ...

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO driver fixes, along with two staging driver fixes
  for 4.6-rc3.

  One staging driver patch reverts the deletion of a driver that
  happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
  still alive and kicking, and has users that were mad we broke their
  hardware by deleting a driver for their machines.  So that driver is
  added back and everyone is happy again.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Revert "Staging: olpc_dcon: Remove obsolete driver"
  staging/rdma/hfi1: select CRC32
  iio: gyro: bmg160: fix buffer read values
  iio: gyro: bmg160: fix endianness when reading axes
  iio: accel: bmc150: fix endianness when reading axes
  iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
  iio: fix config watermark initial value
  iio: health: max30100: correct FIFO check condition
  iio: imu: Fix inv_mpu6050 dependencies
  iio: adc: Fix build error of missing devm_ioremap_resource on UM
  iio: light: apds9960: correct FIFO check condition
  iio: adc: max1363: correct reference voltage
  iio: adc: max1363: add missing adc to max1363_id

Pull SCSI fixes from James Bottomley:
 "This is a set of eight fixes.

  Two are trivial gcc-6 updates (brace additions and unused variable
  removal).  There's a couple of cxlflash regressions, a correction for
  sd being overly chatty on revalidation (causing excess log increases).
  A VPD issue which could crash USB devices because they seem very
  intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
  overrun fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Do not attach VPD to devices that don't support it
  sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
  scsi_dh_alua: Fix a recently introduced deadlock
  scsi: Declare local symbols static
  cxlflash: Move to exponential back-off when cmd_room is not available
  cxlflash: Fix regression issue with re-ordering patch
  mpt3sas: Don't overreach ioc->reply_post[] during initialization
  aacraid: add missing curly braces

Pull MD fixes from Shaohua Li:
 "This update mainly fixes bugs:

   - fix error handling (Guoqing)
   - fix a crash when a disk is hotremoved (me)
   - fix a dead loop (Wei Fang)"

* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/bitmap: clear bitmap if bitmap_create failed
  MD: add rdev reference for super write
  md: fix a trivial typo in comments
  md:raid1: fix a dead loop when read from a WriteMostly disk

Pull power management and ACPI fixes from Rafael Wysocki:
 "Fixes for some issues discovered after recent changes and for some
  that have just been found lately regardless of those changes
  (intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
  support for some new CPU models (intel_idle, Intel RAPL driver,
  turbostat) and documentation updates (intel_pstate, PM core).

  Specifics:

   - intel_pstate fixes for two issues exposed by the recent switch over
     from using timers and for one issue introduced during the 4.4 cycle
     plus new comments describing data structures used by the driver
     (Rafael Wysocki, Srinivas Pandruvada).

   - intel_idle fixes related to CPU offline/online (Richard Cochran).

   - intel_idle support (new CPU IDs and state definitions mostly) for
     Skylake-X and Kabylake processors (Len Brown).

   - PCC mailbox driver fix for an out-of-bounds memory access that may
     cause the kernel to panic() (Shanker Donthineni).

   - New (missing) CPU ID for one apparently overlooked Haswell model in
     the Intel RAPL power capping driver (Srinivas Pandruvada).

   - Fix for the PM core's wakeup IRQs framework to make it work after
     wakeup settings reconfiguration from sysfs (Grygorii Strashko).

   - Runtime PM documentation update to make it describe what needs to
     be done during device removal more precisely (Krzysztof Kozlowski).

   - Stale comment removal cleanup in the cpufreq-dt driver (Viresh
     Kumar).

   - turbostat utility fixes and support for Broxton, Skylake-X and
     Kabylake processors (Len Brown)"

* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
  PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
  tools/power turbostat: work around RC6 counter wrap
  tools/power turbostat: initial KBL support
  tools/power turbostat: initial SKX support
  tools/power turbostat: decode BXT TSC frequency via CPUID
  tools/power turbostat: initial BXT support
  tools/power turbostat: print IRTL MSRs
  tools/power turbostat: SGX state should print only if --debug
  intel_idle: Add KBL support
  intel_idle: Add SKX support
  intel_idle: Clean up all registered devices on exit.
  intel_idle: Propagate hot plug errors.
  intel_idle: Don't overreact to a cpuidle registration failure.
  intel_idle: Setup the timer broadcast only on successful driver load.
  intel_idle: Avoid a double free of the per-CPU data.
  intel_idle: Fix dangling registration on error path.
  intel_idle: Fix deallocation order on the driver exit path.
  intel_idle: Remove redundant initialization calls.
  intel_idle: Fix a helper function's return value.
  intel_idle: remove useless return from void function.
  ...

Pull networking fixes from David Miller:

 1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
    from Haishuang Yan.

 2) Fix multicast frame handling in mac80211 AP code, from Felix
    Fietkau.

 3) mac80211 station hashtable insert errors not handled properly, fix
    from Johannes Berg.

 4) Fix TX descriptor count limit handling in e1000, from Alexander
    Duyck.

 5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.

 6) Must assign rtnl_link_ops of the device before registering it, fix
    in ip6_tunnel from Thadeu Lima de Souza Cascardo.

 7) Memory leak fix in tc action net exit, from WANG Cong.

 8) Add missing AF_KCM entries to name tables, from Dexuan Cui.

 9) Fix regression in GRE handling of csums wrt.  FOU, from Alexander
    Duyck.

10) Fix memory allocation alignment and congestion map corruption in
    RDS, from Shamir Rabinovitch.

11) Fix default qdisc regression in tuntap driver, from Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  bridge, netem: mark mailing lists as moderated
  tuntap: restore default qdisc
  mpls: find_outdev: check for err ptr in addition to NULL check
  ipv6: Count in extension headers in skb->network_header
  RDS: fix congestion map corruption for PAGE_SIZE > 4k
  RDS: memory allocated must be align to 8
  GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
  net: add the AF_KCM entries to family name tables
  MAINTAINERS: intel-wired-lan list is moderated
  lib/test_bpf: Add additional BPF_ADD tests
  lib/test_bpf: Add test to check for result of 32-bit add that overflows
  lib/test_bpf: Add tests for unsigned BPF_JGT
  lib/test_bpf: Fix JMP_JSET tests
  VSOCK: Detach QP check should filter out non matching QPs.
  stmmac: fix adjust link call in case of a switch is attached
  af_packet: tone down the Tx-ring unsupported spew.
  net_sched: fix a memory leak in tc action
  samples/bpf: Enable powerpc support
  samples/bpf: Use llc in PATH, rather than a hardcoded value
  samples/bpf: Fix build breakage with map_perf_test_user.c
  ...

Pull btrfs fixes from Chris Mason:
 "These are bug fixes, including a really old fsync bug, and a few trace
  points to help us track down problems in the quota code"

* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix file/data loss caused by fsync after rename and new inode
  btrfs: Reset IO error counters before start of device replacing
  btrfs: Add qgroup tracing
  Btrfs: don't use src fd for printk
  btrfs: fallback to vmalloc in btrfs_compare_tree
  btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
  btrfs: Output more info for enospc_debug mount option
  Btrfs: fix invalid reference in replace_path
  Btrfs: Improve FL_KEEP_SIZE handling in fallocate

Pull orangefs fixes from Mike Marshall:
 "Orangefs cleanups and a strncpy vulnerability fix.

  Cleanups:
   - remove an unused variable from orangefs_readdir.
   - clean up printk wrapper used for ofs "gossip" debugging.
   - clean up truncate ctime and mtime setting in inode.c
   - remove a useless null check found by coccinelle.
   - optimize some memcpy/memset boilerplate code.
   - remove some useless sanity checks from xattr.c

  Fix:
   - fix a potential strncpy vulnerability"

* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: remove unused variable
  orangefs: Add KERN_<LEVEL> to gossip_<level> macros
  orangefs: strncpy -> strscpy
  orangefs: clean up truncate ctime and mtime setting
  Orangefs: fix ifnullfree.cocci warnings
  Orangefs: optimize boilerplate code.
  Orangefs: xattr.c cleanup

Pull IOMMU fixes from Joerg Roedel:

 - compile-time fixes (warnings and failures)

 - a bug in iommu core code which could cause the group->domain pointer
   to be falsly cleared

 - fix in scatterlist handling of the ARM common DMA-API code

 - stall detection fix for the Rockchip IOMMU driver

* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/vt-d: Silence an uninitialized variable warning
  iommu/rockchip: Fix "is stall active" check
  iommu: Don't overwrite domain pointer when there is no default_domain
  iommu/dma: Restore scatterlist offsets correctly
  iommu: provide of_xlate pointer unconditionally

Make sure we avoid a division-by-zero OOPS in case clock-frequency is
set too low in DT. Add missing '\n' while we are here.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NAxel Lin <axel.lin@ingics.com>

This reverts commit 34cf2acd. 'ret' is
not set when bailing out. Also, there is a better place to check for 0.
Reported-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Merge tag 'usb-serial-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.6-rc3

Here are some new device ids.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Merge tag 'mac80211-for-davem-2016-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
For the current RC series, we have the following fixes:
 * TDLS fixes from Arik and Ilan
 * rhashtable fixes from Ben and myself
 * documentation fixes from Luis
 * U-APSD fixes from Emmanuel
 * a TXQ fix from Felix
 * and a compiler warning suppression from Jeff
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I moderate these (lightly loaded) lists to block spam.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>