Sometimes suspend thread queues a command and wait for it's
response, meanwhile WLAN driver power cycles the card which
leads to crash. This patch makes sure that suspend thread is
woken up in remove path.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change improves readability and fixes allignment problem.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of the message.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This flag will be set in unload path to make sure that we skip
sending further commands, ignore interrupts and stop main thread
when unload starts.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If module init command fails, FW might not be in good state.
We will return from setup handler and skip downloading further
commands.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

btmrvl_remove_card() calls kthread_stop() to stop the main thread,
but kthread_should_stop() is checked when all the activities are done
in the main thread before sleeping.
We will have kthread_should_stop() check as soon as main thread is
woken up. This fixes a crash issue caused due to an invalid memory
access while unnecessarily processing interrupts after card removal.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Silicon Wave based devices do support Inquiry Result with RSSI and
so let the core know to enable them.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Roper Class 1 Bluetooth Dongle is another device that claims to
support Bluetooth 1.2 specification, but does not support the HCI
command for reading the local supported commands.

  < HCI Command: Read Local Version Information (0x04|0x0001) plen 0
  > HCI Event: Command Complete (0x0e) plen 12
      Read Local Version Information (0x04|0x0001) ncmd 1
      status 0x00
      HCI Version: 1.2 (0x2) HCI Revision: 0x0
      LMP Version: 1.2 (0x2) LMP Subversion: 0x757
      Manufacturer: Silicon Wave (11)

It clearly claims Bluetooth 1.2 support and in that regard has the
same issue as the AVM BlueFritz! USB devices (Silicon Wave based),
but the HCI Read Local Supported Commands command fails.

  < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
  > HCI Event: Command Status (0x0f) plen 4
      Read Local Supported Commands (0x04|0x0002) status 0x01 ncmd 1
      Error: Unknown HCI Command

Use the HCI_QUIRK_BROKEN_LOCAL_COMMANDS quirk for these devices and
the failing command will be skipped.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Currently the only tunnel protocol that supports GRO with encapsulated
Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer
so that it can be used by other tunnel protocols such as GRE and Geneve.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to set the clock speed in read/write which will be performed
unnecessarily for each mdio access. Init it during probe is enough.

Also, the hardcoded clock value is not a proper way for all SoCs.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Which is wrong and not used, so no extra space needed by
mdiobus_alloc_size(), use mdiobus_alloc() instead.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the reset is just clock setting, individual mdio reset is
not available.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

modify CRU config for GMAC driver

changes since v2:
1. remove SCLK_MAC_PLL
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver is based on stmmac driver.

changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)

changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of -1 with EAGAIN, read on a O_NONBLOCK tun fd will return 0.  This
fixes this by properly returning the error code from __skb_recv_datagram.
Signed-off-by: NAlex Gartrell <agartrell@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Validated that this was actually using the unsigned comparison with gdb.
Signed-off-by: NAlex Gartrell <agartrell@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds generic statistics for enic. As of now dma_map_error is the only
member. dma_map_erro is incremented every time dma maping error happens.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch checks for pci_dma_mapping_error() after dma mapping the data.
If the dma mapping fails we remove the previously queued frags and return
NETDEV_TX_OK.
Reported-by: NJan Stancek <jstancek@redhat.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes vnic_wq_buf doubly liked list. This is needed for dma_mapping
error check, in case some frag's dma map fails, we need to move back and remove
previously queued buffers.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode
in low power status, when system enter suspend status, Magic packet can
wake up system even if all SOC clocks are gate. The patch doing below things:
- flagging the device as a wakeup source for the system, as well as
  its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- add standard ethtool WOL interface
- enable the ENET interrupt to wake us

Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following spare warning:
drivers/net/ethernet/freescale/gianfar.c:3521:60: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:3521:60:    expected unsigned int [noderef] <asn:2>*addr
drivers/net/ethernet/freescale/gianfar.c:3521:60:    got unsigned int [usertype] *rfbptr
drivers/net/ethernet/freescale/gianfar.c:205:16: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:205:16:    expected unsigned int [usertype] *rfbptr
drivers/net/ethernet/freescale/gianfar.c:205:16:    got unsigned int [noderef] <asn:2>*<noident>
drivers/net/ethernet/freescale/gianfar.c:2918:44: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:2918:44:    expected unsigned int [noderef] <asn:2>*addr
drivers/net/ethernet/freescale/gianfar.c:2918:44:    got unsigned int [usertype] *rfbptr
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no need to do header check for virtio-net since:

- Host sets dodgy for all gso packets from guest and check the header.
- Host should be prepared for all kinds of evil packets from guest, since
  malicious guest can send any kinds of packet.

So this patch sets NETIF_F_GSO_ROBUST for virtio-net to skip the check.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the end asm/mach/irda.h header is not used by anybody except sa1100.
Move the header to the platform data includes dir and rename it to
irda-sa11x0.h.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current timecounter implementation will drop a variable amount
of resolution, depending on the magnitude of the time delta. In
other words, reading the clock too often or too close to a time
stamp conversion will introduce errors into the time values. This
patch fixes the issue by introducing a fractional nanosecond field
that accumulates the low order bits.
Reported-by: NJanusz Użycki <j.uzycki@elproma.com.pl>
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.

Compile tested only.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>