To issue a port query, use the QUERY_(Ethernet)_PORT command instead
of the MAD_IFC command, since MAD_IFC attempts to query the firmware
IB SMA, which is irrelevant for IBoE ports.

This allows us to handle both 10Gb/s and 40Gb/s rates (e.g in sysfs),
using QDR speed (10Gb/s) and width of 1X or 4X.
Signed-off-by: NDotan Barak <dotanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

If an erroneous CQE is polled in the first iteration (i.e. npolled ==
0), we don't update the consumer index and hence the hardware could
get a wrong notion of how many CQEs software polled.  Fix this by
unconditionally updating the doorbell record.  We could change the
check to be something like

	if (npolled || err != -EAGAIN)
		...

but it does not seem worth the effort since a posted write to memory
should not cost too much.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt.  The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.

Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

If the opcode of a work request exceeds the range of valid opcodes,
return the pointer to the offending work request.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Update copyright information in the source files.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

In the current code, vendor-specific MADs (e.g with the FDR-10
attribute) are silently dropped by the driver, resulting in timeouts
at the sending side and inability to query/configure the relevant
feature.  However, the ConnectX firmware is able to handle such MADs.
For unsupported attributes, the firmware returns a GET_RESPONSE MAD
containing an error status.

For example, for a FDR-10 node with LID 11:

    # ibstat mlx4_0 1

    CA: 'mlx4_0'
    Port 1:
    State: Active
    Physical state: LinkUp
    Rate: 40 (FDR10)
    Base lid: 11
    LMC: 0
    SM lid: 24
    Capability mask: 0x02514868
    Port GUID: 0x0002c903002e65d1
    Link layer: InfiniBand

Extended Port Query (EPI) vendor mad timeouts before the patch:

    # smpquery MEPI 11 -d

    ibwarn: [4196] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
    ibwarn: [4196] _do_madrpc: retry 1 (timeout 1000 ms)
    ibwarn: [4196] _do_madrpc: retry 2 (timeout 1000 ms)
    ibwarn: [4196] _do_madrpc: timeout after 3 retries, 3000 ms
    ibwarn: [4196] mad_rpc: _do_madrpc failed; dport (Lid 11)
    smpquery: iberror: [pid 4196] main: failed: operation EPI: ext port info query failed

EPI query works OK with the patch:

    # smpquery MEPI 11 -d

    ibwarn: [6548] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
    ibwarn: [6548] mad_rpc: data offs 64 sz 64
    mad data
    0000 0000 0000 0001 0000 0001 0000 0001
    0000 0000 0000 0000 0000 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000
    0000 0000 0000 0000 0000 0000 0000 0000
    # Ext Port info: Lid 11 port 0
    StateChangeEnable:...............0x00
    LinkSpeedSupported:..............0x01
    LinkSpeedEnabled:................0x01
    LinkSpeedActive:.................0x01
Signed-off-by: NJack Morgenstein <jackm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Acked-by: NIra Weiny <weiny2@llnl.gov>
Cc: <stable@vger.kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix fast memory registration opcode in local invalidate completion.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NDonald Wood <Donald.E.Wood@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Zero high order word of fast memory registration (FMR) length field.
FMR length field is 32 bits, so high word should always be zero.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NDonald Wood <Donald.E.Wood@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Commit 8d4548f2 ("IB/qib: Default some module parameters optimally")
introduced an issue with older root complexes.  They cannot handle the
pcie_caps of 0x51 (MaxReadReq 4096, MaxPayload=256).

A typical diagnostic in this situation reported by syslog contains
the text:

  [PCIe Poisoned TLP][Send DMA memory read]

Restore the module paramter default to zero with will avoid any
changes in the root complex.
Reviewed-by: NMark Debbage <mark.debbage@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

alloc_dummy_hdrq() is called with locks held and thus should not use
GFP_KERNEL.

The semantic patch that makes this report is available in
scripts/coccinelle/locks/call_kern.cocci.
Signed-off-by: NJulia Lawall <julia.lawall@lip6.fr>
Acked-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Make sure all exit paths from this function unlock everything.
Reported-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Set a reject flag, when sending MPA reject message to inform the peer
that the application has rejected the connection.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

"dentry" is a valid pointer.  "*dentry" was intended.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

For historical reasons, we allow module_param(bool) to take an int (or
an unsigned int).  That's going away.

A few drivers really want an int: they set it to -1 and a parameter
will set it to 0 or 1.  This sucks: reading them from sysfs will give
'Y' for both -1 and 1, but if we change it to an int, then the users
might be broken (if they did "param" instead of "param=1").

Use a new 'bint' parser for them.

(ntfs has a different problem: it needs an int for debug_msgs because
it's also exposed via sysctl.)

Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux390@de.ibm.com
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: lm-sensors@lm-sensors.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-ntfs-dev@lists.sourceforge.net
Cc: alsa-devel@alsa-project.org
Acked-by: Takashi Iwai <tiwai@suse.de> (For the sound part)
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> (For the hwmon driver)
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Fix for reset which happens right after sending a terminate message.
Terminate timer is not deleted when the connection is closed.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Warned about by sparse.
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Change the PHY clock divisor to make the MDIO clock 2.5MHz, instead of
3.5MHz (which is out of spec).
Signed-off-by: NTatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: NFaisal Latif <Faisal.Latif@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For IBoE, SLs 0-7 are mapped to Ethernet 802.1Q user priority bits
(pbits) which are part of the VLAN tag, SLs 8-15 are reserved.

Under Ethernet, the ConnectX firmware treats (decode/encode) the four
bit SL field in various constructs such as QPC / UD WQE / CQE as PPP0
and not as 0PPP. This correlates well to the fact that within the
vlan tag the pbits are located in bits 15-13 and not 12-14.

The current code wasn't consistent around that area - the
encoding was correct for the IBoE QPC.path.schedule_queue field,
but was wrong for IBoE CQEs and when MLX header was built.

These inconsistencies resulted in wrong SL <--> wire 802.1Q pbits
mapping, which is fixed by using SL <--> PPP0 all around the place.
Signed-off-by: NOren Duer <oren@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Minimize the need for users to have to set module parameters to get
good performance.

The following two parameters are changed:
 - rcvhdrcnt to twice the rcvegrcnt
 - pcie_caps=0x51

The rcvhdrcnt at twice the egrcount allows the preemptive NAK code
during reception to function in 100% of the cases rather than a sender
jiffies-based timeout.

The pcie_caps default of 0x51 will set the proposed MaxPayload and
MaxReceiveReqest to 256 and 4096 respectively.  The capabilities on
the root complex will be used to limit those values.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The current code locks the QP s_lock, followed by the pending_lock, I
guess to to protect against the allocate failing.

This patch only locks the pending_lock, assuming that the empty case
is an exeception, in which case the pending_lock is dropped, and the
original code is executed.  This will save a lock of s_lock in the
normal case.

The observation is that the sdma descriptors will deplete at twice the
rate of txreq's, so this should be rare.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Prevent a receive data corruption by ensuring that the write to update
the rcvhdrheadn register to generate an interrupt is at the very end
of the receive processing.
Signed-off-by: NRamkrishna Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The qib driver makes use of the the 64-bit jiffies API.

Code inspection reveals that that version of the API is not really
required.  This patch converts to use the "normal" jiffies.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

More style issues revealed with checkpatch.pl -f.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Commit 53ab1c64 ("IB/qib: Correct nfreectxts for multiple HCAs")
reversed the increments and decrements of dd->nfreectxts.  Fix it.
Reviewed-by: NRam Vepa <ram.vepa@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).

This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.

Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit cfcde11c ("IB/mlx4: Use flow counters on IBoE ports") added
code that sets elements of counters[] to -1 if no counter is allocated,
but then goes ahead and passes every entry to mlx4_counter_free() on
shutdown.  This is a bad idea, especially if MLX4_DEV_CAP_FLAG_COUNTERS
isn't set so there isn't even an underlying bitmap to free from.
Tested-by: NSean Hefty <sean.hefty@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Three pieces of code do the same thing, create a l2t entry and then
import this information into the c4iw_ep object.

Create a helper function and call it from these 3 locations instead.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRoland Dreier <roland@purestorage.com>

Do this instead of performing a by-hand lookup.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRoland Dreier <roland@purestorage.com>

This way we consolidate the RCU locking down into the place where it
actually matters, and also we can make the code handle
dst_get_neighbour_noref() returning NULL properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRoland Dreier <roland@purestorage.com>

Commit f2c31e32 ("net: fix NULL dereferences in check_peer_redir()")
forgot to take care of infiniband uses of dst neighbours.

Many thanks to Marc Aurele who provided a nice bug report and feedback.
Reported-by: NMarc Aurele La France <tsi@ualberta.ca>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Don't over-schedule QSFP work on driver initialization.  It could end
up being run simultaneously on two different CPUs resulting in bad
EEPROM reads.  In combination with setting the physical IB link state
prior to the IBC being brought out of reset, this can cause the link
state machine to start training early with wrong settings.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix logic so that we don't retry with MPAv1 once we have done that
already.  Otherwise, we end up retrying with MPAv1 even when its not
needed on getting peer aborts - and this could lead to kernel panic.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Fix another place in the code where logic dealing with the t4_cqe was
using the wrong QID.  This fixes the counting logic so that it tests
against the SQ QID instead of the RQ QID when counting RCQES.

Signed-off by: Jonathan Lallinger <jonathan@ogc.us>
Signed-off by: Steve Wise <swise@ogc.us>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was mistakenly introduced by dde05cbd ("IB/qib: Hold links
until tuning data is available").
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>