Pull arm64 fixes from Catalin Marinas:
 - Stack size increased to 16K (similar to other 64-bit architectures)
 - Additional cache flushing for secondary CPUs boot mode

* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: Change kernel stack size to 16K
  arm64: Fix definition of arm_pm_restart to match the declaration
  arm64: virt: ensure visibility of __boot_cpu_mode

Pull ARM SoC fixes from Olof Johansson:
 "This is a largeish batch of fixes, mostly because I missed -rc2 due to
  travel/vacation.  So in number these are a bit more than ideal unless
  you amortize them over two -rcs.

  Quick breakdown:
   - Defconfig updates
     - Making multi_v7_defconfig useful on more hardware to encourage
       single-image usage
     - Davinci and nomadik updates due to new code merged this merge
       window
   - Fixes for UART on Samsung platforms, both PM and clock-related
   - A handful of warning fixes from defconfig builds, including for
     max8925 backlight and pxamci (both with appropriate acks)
   - Exynos5440 fixes for LPAE configuration, PM
   - ...plus a bunch of other smaller changes all over the place

  I expect to switch to regressions-or-severe-bugs-only fixes from here
  on out"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
  mfd: max8925: fix dt code for backlight
  ARM: omap5: Only select errata 798181 if SMP
  ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
  ARM: EXYNOS: Fix low level debug support
  ARM: SAMSUNG: Save/restore only selected uart's registers
  ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
  ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
  ARM: multi_v7_defconfig: Select USB chipidea driver
  ARM: pxa: propagate errors from regulator_enable() to pxamci
  ARM: zynq: fix compilation warning
  ARM: keystone: fix compilation warning
  ARM: highbank: Only touch common coherency control register fields
  ARM: footbridge: fix overlapping PCI mappings
  dmaengine: shdma: fix a build failure on platforms with no DMA support
  ARM: STi: Set correct ARM ERRATAs.
  ARM: dts: STi: Fix pinconf setup for STiH416 serial2
  ARM: nomadik: configure for NO_HZ and HRTIMERS
  ARM: nomadik: update defconfig base
  ARM: nomadik: Update MMC defconfigs
  ARM: davinci: defconfig: enable EDMA driver
  ...

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for 3.11-rc3.

  Lots of little things, nothing major.  A number of new device ids,
  build fixes for DMA, and a bunch of other minor things.  All of these
  have been in the linux-next tree"

* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
  usb: Clear both buffers when clearing a control transfer TT buffer.
  usb/gadget: free opts struct on error recovery
  USB: mos7840: fix memory leak in open
  usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
  usb: serial: option: add Olivetti Olicard 200
  usb: serial: option: blacklist ONDA MT689DC QMI interface
  xhci: fix null pointer dereference on ring_doorbell_for_active_rings
  usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
  usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
  usb: xhci: Mark two functions __maybe_unused
  xhci: Avoid NULL pointer deref when host dies.
  usb: serial: option: Add ONYX 3G device support
  USB: ti_usb_3410_5052: fix dynamic-id matching
  usb: option: add TP-LINK MA260
  USB: option: add D-Link DWM-152/C1 and DWM-156/C1
  USB: EHCI: Fix resume signalling on remote wakeup
  USB: cp210x: add MMB and PI ZigBee USB Device Support
  usb: cp210x support SEL C662 Vendor/Device
  USB: option: append Petatel NP10T device to GSM modems list
  USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
  ...

Pull tty/serial fixes from Greg KH:
 "Here are 3 fixes for TTY and serial issues that have been reported.
  Nothing huge, but nice to get fixed"

* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
  tty/8250_early: Don't truncate last character of options
  TTY: snyclinkmp: calculating wrong addresses

Pull staging fixes from Greg KH:
 "Here are some tiny drivers/staging/ fixes for 3.11-rc3

  A number of bugfixes, all pretty tiny, but resolve issues that have
  been reported (the kstrtos32 change fixes a data corruption problem
  that Dan found).  And a MAINTAINERS file update for the comedi
  drivers"

* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  MAINTAINERS: Update the list of maintainers for staging/comedi driver.
  staging: tidspbridge: replace strict_strtol() with kstrtos32()
  staging: android: logger: Correct write offset reset on error
  staging: zram: protect zram_reset_device() call
  staging: gdm72xx: potential use after free in send_qos_list()
  staging: drm/imx: drop "select OF_VIDEOMODE"
  staging: frontier: use after free in disconnect()
  staging: comedi: fix a race between do_cmd_ioctl() and read/write
  staging: comedi: COMEDI_CANCEL ioctl should wake up read/write

Pull char/misc patches from Greg KH:
 "Here are some char/misc patches for 3.11-rc3.  It's pretty much just:
   - mei fixes
   - hyperv fixes
   - new ja_JP translation update
  all tiny stuff, but fixes for issues people have reported."

* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  HOWTO ja_JP sync
  mei: me: fix waiting for hw ready
  mei: don't have to clean the state on power up
  mei: me: fix reset state machine
  mei: hbm: fix typo in error message
  Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
  Drivers: hv: balloon: Do not post pressure status if interrupted
  Drivers: hv: balloon: Fix a bug in the hot-add code
  Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered

Pull sound fixes from Takashi Iwai:
 "Just a handful of regression and small fixes in ASoC, HD-audio and
  USB-audio drivers.

   - Sigmetal HD-audio codec regression fixes
   - A copule of XRUN indication fixes for usb-audio devices
   - ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
     max98088 register access fix, etc"

* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hiface: return correct XRUN indication
  ASoC: tegra: correct playback_dma_data setup
  ASoC: core: double free in snd_soc_add_platform()
  ALSA: usb-audio: 6fire: return correct XRUN indication
  ASoC: ep93xx: fix build of ep93xx-ac97.c
  ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
  ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
  ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
  ASoC: sgtl5000: defer the probe if clock is not found
  ASoC: max98088 - fix element type of the register cache.

Pull xfs fix from Ben Myers:
 "Fix for regression in commit cca9f93a ("xfs: don't do IO when
  creating an new inode"), recovery causing filesystem corruption after
  a crash"

* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
  xfs: di_flushiter considered harmful

Pull nfsd fix from Bruce Fields:
 "One more nfsd bugfix for 3.11"

* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
  nfsd: nfsd_open: when dentry_open returns an error do not propagate as struct file

Pull md fixes from Neil Brown:
 "Two more bugfixes for md in 3.11

  Both marked for -stable, both since 3.3.  I guess I should spend more
  time testing..."

* tag 'md/3.11-fixes' of git://neil.brown.name/md:
  md/raid5: fix interaction of 'replace' and 'recovery'.
  md/raid10: remove use-after-free bug.

Pull libata fixes from Tejun Heo:
 "Assorted libata updates.

  The most critical one is a fix for ahci oops during boot.  Also, a new
  smallish platform ahci driver is added and sata_inic162x is marked
  clearly as experimental (it whines during boot too) as data corruption
  seems rather common on the device and it's unlikely to get any love in
  the foreseeable future.  If the whining doesn't draw any attention, I
  think we'd probably be better of making the driver depend on BROKEN in
  a couple releases"

This is v2 of this pull request with fixed dependencies for ahci_imx.

* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci_imx: depend on CONFIG_MFD_SYSCON
  ahci_imx: add ahci sata support on imx platforms
  ARM: imx6q: update the sata bits definitions of gpr13
  ahci: fix Null pointer dereference in achi_host_active()
  libata: make it clear that sata_inic162x is experimental
  libata: replace strict_strtol() with kstrtol()
  ata: Fix DVD not dectected at some platform with Wellsburg PCH

ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not.  Add the Kconfig dependency.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>

Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.
Signed-off-by: NFeng Kan <fkan@apm.com>
Acked-by: NKumar Sankaran <ksankaran@apm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The device-tree enablement for max8925 has several problems, but besides
the bindings being wrong (and not having seen review) there's also some
bad coding practices on how to fill in the platform_data from device tree.

I came across this since it causes a warning when compiling
mmp2_defconfig, and instead of doing the minimal fix to silence the
warning, I restructured the code a bit.

This silences the warning:
drivers/video/backlight/max8925_bl.c: In function 'max8925_backlight_probe':
drivers/video/backlight/max8925_bl.c:177:3: warning: statement with no effect [-Wunused-value]

Note that the bindings themselves need to be revisited too, but that will
affect more than just the backlight driver and is best done separately;
this just fixes the bad code for the backlight driver.
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: NWilliam Gulland <wgulland@google.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix memory leaks introduced in commits:

40d133d7
usb: gadget: f_ncm: convert to new function interface with backward compatibility

fee562a6
usb: gadget: f_ecm: convert to new function interface with backward compatibility

fcbdf12e
usb: gadget: f_phonet: convert to new function interface with backward compatibility

b29002a1
usb: gadget: f_eem: convert to new function interface with backward compatibility

8cedba7c
usb: gadget: f_subset: convert to new function interface with backward compatibility

f466c635
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allocated urbs and buffers were never freed on errors in open.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: Nenrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-linus-2013-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:

xhci: Bug fixes, now with more tags!

Hi Greg,

Here's five bug fixes for 3.12.

The three patches are marked for stable.  Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.

The other two patches fix build warnings.

Sarah Sharp

When we made all inode updates transactional, we no longer needed
the log recovery detection for inodes being newer on disk than the
transaction being replayed - it was redundant as replay of the log
would always result in the latest version of the inode would be on
disk. It was redundant, but left in place because it wasn't
considered to be a problem.

However, with the new "don't read inodes on create" optimisation,
flushiter has come back to bite us. Essentially, the optimisation
made always initialises flushiter to zero in the create transaction,
and so if we then crash and run recovery and the inode already on
disk has a non-zero flushiter it will skip recovery of that inode.
As a result, log recovery does the wrong thing and we end up with a
corrupt filesystem.

Because we have to support old kernel to new kernel upgrades, we
can't just get rid of the flushiter support in log recovery as we
might be upgrading from a kernel that doesn't have fully transactional
inode updates.  Unfortunately, for v4 superblocks there is no way to
guarantee that log recovery knows about this fact.

We cannot add a new inode format flag to say it's a "special inode
create" because it won't be understood by older kernels and so
recovery could do the wrong thing on downgrade. We cannot specially
detect the combination of zero mode/non-zero flushiter on disk to
non-zero mode, zero flushiter in the log item during recovery
because wrapping of the flushiter can result in false detection.

Hence that makes this "don't use flushiter" optimisation limited to
a disk format that guarantees that we don't need it. And that means
the only fix here is to limit the "no read IO on create"
optimisation to version 5 superblocks....
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NMark Tinguely <tinguely@sgi.com>
Signed-off-by: NBen Myers <bpm@sgi.com>

(cherry picked from commit e60896d8)

in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.

This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.

Note from Sarah:

The xHCI 1.0 spec changed how hardware handles short packets.  The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set).  On the second successful status, that warning will be
triggered in the driver.

Software is now supposed to not assume the TD is not completed until it
gets that last successful status.  That means we have a slight race
condition, although it should have little practical impact.  This patch
papers over that issue.

It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable.  This
patch is needed for stable to avoid serious log spam.

This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333 "Intel xhci:
Ignore spurious successful event."

The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Fix warning when CONFIG_PCI is not enabled
(from commit 29636578).

drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]

These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
  dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.

Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().

The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL.  The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.

However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory.  xhci_free_dev checks the return value from the generic
xhci_check_args function.  If the return value is -ENODEV, it carries on
trying to free the virtual device.

The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer.  It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.

The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.

See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details.  This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.

This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b40 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NVincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org

If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.

This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).

So schedule those writes when s.replacing is set as well.

In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete.  So introduce STRIPE_REPLACED to
record if the replacement has happened.

For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test.  The latter
ensure that now IO has been flagged but not started.  The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.

Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.

Finally if a NeedReplace device is not UPTODATE then that is an
error.  We really must trigger a warning.

This bug was introduced in commit 9a3e1101
(md/raid5:  detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.

Cc: stable@vger.kernel.org (3.3+)
Reported-by: Nqindehua <13691222965@163.com>
Tested-by: Nqindehua <qindehua@163.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

We always need to be careful when calling generic_make_request, as it
can start a chain of events which might free something that we are
using.

Here is one place I wasn't careful enough.  If the wbio2 is not in
use, then it might get freed at the first generic_make_request call.
So perform all necessary tests first.

This bug was introduced in 3.3-rc3 (24afd80d) and can cause an
oops, so fix is suitable for any -stable since then.

Cc: stable@vger.kernel.org (3.3+)
Signed-off-by: NNeilBrown <neilb@suse.de>

Attached is Documentation/ja_JP/HOWTO sync patch for 3.10.
This patch was reviewed by Japanese translation community called JF.
Signed-off-by: NTsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: NEnrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

From Kukjin Kim:
Samsung fixes for v3.11
- fix kernel booting on exynos5440
  skip pm which is not supported
  update regarding LPAE features
- fix s3c2440 uart with adding clkdev entries
- fix compilatioin for Samsung SoCs with selecting pm
- update ARCH_NR_GPIO to support exynos4412 has more gpios

* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
  ARM: EXYNOS: Fix low level debug support
  ARM: SAMSUNG: Save/restore only selected uart's registers
  ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
  ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
  ARM: EXYNOS: Enable 64-bit DMA for EXYNOS5440 if LPAE is enabled
  ARM: EXYNOS: change the PHYSMEM_BITS and SECTION_SIZE
  ARM: EXYNOS: skip pm support on exynos5440
Signed-off-by: NOlof Johansson <olof@lixom.net>

Avoids the following warning when SMP is off:

warning: (ARCH_KEYSTONE && SOC_OMAP5) selects ARM_ERRATA_798181 which
has unmet direct dependencies (CPU_V7 && SMP)
Reported-by: NEmilio López <emilio@elopez.com.ar>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.

Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: NAnders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ttyTHS is consistent with the name used in driver.
Signed-off-by: NRichard Zhao <rizhao@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The earlier change to use strlcpy uncovered a bug in the options
argument length calculation causing last character to be truncated.
This makes the actual console to be configured with incorrect
baudrate when specifying the console using console=uart,... syntax.

Bug symptom seen in kernel log output:

Kernel command line: console=uart,mmio,0x90000000,115200
Early serial console at MMIO 0x90000000 (options '11520')

which then results in a invalid baud rate 11520 instead of the
expected 115200 when the console is switched to ttyS0 later
in the boot process.
Signed-off-by: NHenrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a static checker fix and I don't have a way to test it.  But
from the context it looks like this is a typo where SCABUFSIZE was
intended instead of sizeof(SCABUFSIZE).  SCABUFSIZE is 1024 and
sizeof(int) is 4.  I would suspect this is a bad bug.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull powerpc fixes from Ben Herrenschmidt:
 "Here is a series of powerpc fixes.  It's a bit big, mostly because of
  the series of 11 "EEH" patches from Gavin.  The EEH (Our IBM specific
  PCI/PCIe Enhanced Error Handling) code had been rotting for a while
  and this merge window saw a significant rework & fixing of it by Gavin
  Shan.

  However, that wasn't complete and left some open issues.  There were
  still a few corner cases that didn't work properly, for example in
  relation to hotplug and devices without explicit error handlers.  We
  had some patches but they weren't quite good enough yet so I left them
  off the 3.11 merge window.

  Gavin since then fixed it all up, we ran quite a few rounds of testing
  and it seems fairly solid (at least probably more than it has ever
  been).  This should probably have made -rc1 but both Gavin and I took
  some vacation so it had to wait for -rc2.

  The rest is more bug fixes, mostly to new features recently added, for
  example, we missed the cpu table entry for one of the two models of P8
  (we didn't realize they had different PVR [Processor Version Register]
  values), some module CRC issues, etc..."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (23 commits)
  powerpc/perf: BHRB filter configuration should follow the task
  powerpc/perf: Ignore separate BHRB privilege state filter request
  powerpc/powernv: Mark pnv_pci_init_ioda2_phb() as __init
  powerpc/mm: Use the correct SLB(LLP) encoding in tlbie instruction
  powerpc/mm: Fix fallthrough bug in hpte_decode
  powerpc/pseries: Fix a typo in pSeries_lpar_hpte_insert()
  powerpc/eeh: Introdce flag to protect sysfs
  powerpc/eeh: Fix unbalanced enable for IRQ
  powerpc/eeh: Don't use pci_dev during BAR restore
  powerpc/eeh: Use partial hotplug for EEH unaware drivers
  powerpc/pci: Partial tree hotplug support
  powerpc/eeh: Use safe list traversal when walking EEH devices
  powerpc/eeh: Keep PE during hotplug
  powerpc/pci/hotplug: Don't need to remove from EEH cache twice
  powerpc/pci: Override pcibios_release_device()
  powerpc/eeh: Export functions for hotplug
  powerpc/eeh: Remove reference to PCI device
  powerpc: Fix the corrupt r3 error during MCE handling.
  powerpc/perf: Set PPC_FEATURE2_EBB when we register the power8 PMU
  powerpc/pseries: Drop "select HOTPLUG"
  ...

Pull crypto fixes from Herbert Xu:
 "This push fixes a memory corruption issue in caam, as well as
  reverting the new optimised crct10dif implementation as it breaks boot
  on initrd systems.

  Hopefully crct10dif will be reinstated once the supporting code is
  added so that it doesn't break boot"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  Revert "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
  crypto: caam - Fixed the memory out of bound overwrite issue

This patch updates the list of maintainers for the staging/comedi
driver.
Signed-off-by: NLidza Louina <lidza.louina@gmail.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>