Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 05 2月, 2013 3 次提交
  3. 31 1月, 2013 2 次提交
  5. 19 1月, 2013 1 次提交
  7. 18 1月, 2013 1 次提交
  9. 22 11月, 2012 1 次提交
  11. 12 11月, 2012 1 次提交
  13. 13 10月, 2012 1 次提交
  15. 01 10月, 2012 1 次提交
    • S
      pinctrl: add bcm2835 driver · e1b2dc70
      由 Simon Arlott 提交于 
      The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.

Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.

Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
  datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
  implemented are driven by the board, not the GPIO HW block, so don't
  really make sense of a HW block binding, were in general incomplete
  (since they could only know about the few pins hard-coded into the
  Raspberry Pi B board design and not the uncommitted GPIOS), and are
  better represented simply by not writing incorrect data into pin
  configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
  glitches; defer this to gpio_set_direction(). Consequently, removed
  empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
  IRQ handler, thus fixing an issue where the code was indexing into
  enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
  spin_lock_irqsave() and so guarantees it doesn't run concurrently
  with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
  bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
  decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
  directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
  core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
  descriptive.
* Simplified remove(); removed call to non-existent
  pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
  base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      e1b2dc70
  17. 22 9月, 2012 5 次提交
  19. 13 9月, 2012 2 次提交
  21. 07 9月, 2012 2 次提交
  23. 03 9月, 2012 3 次提交
  25. 15 7月, 2012 1 次提交
  27. 21 5月, 2012 2 次提交
  29. 11 5月, 2012 2 次提交
  31. 02 5月, 2012 3 次提交
  33. 23 4月, 2012 1 次提交
  35. 18 4月, 2012 2 次提交
  37. 13 3月, 2012 1 次提交
    • L
      pinctrl: introduce generic pin config · 394349f7
      由 Linus Walleij 提交于 
      This is a split-off from the earlier patch set which adds generic
pin configuration for the pin controllers that want it. Since
we may have a system with mixed generic and custom pin controllers,
we pass a boolean in the pin controller ops vtable to indicate
if it is generic.

ChangeLog v1->v5:
- Follow parent patch versioning number system.
- Document the semantic meaning of return values from pin config
  get functions, so we can iterate over pins and check their
  properties from debugfs as part of the generic config code.
- Use proper cast functions in the generic debugfs pin config
  file.
- Expand generic config to optionally cover groups too.
ChangeLog v5->v6:
- Update to match underlying changes.
ChangeLog v6->v7:
- Drop DRIVE_OFF parameter, use bias high impedance for this
- Delete argument for drive modes push-pull, od and os. These
  are now just state transitions.
- Delete slew rate rising/falling due to discussions on on
  proper semantics
- Drop config wakeup, struct irq_chip does this for now, add
  back if need be.
- Set PIN_CONFIG_END to 0x7fff making room for custom config
  parameters from 0x8000 and up.
- Prefix accessor functions with pinconf_
      394349f7
  39. 06 3月, 2012 1 次提交
  41. 02 2月, 2012 1 次提交
  43. 03 1月, 2012 3 次提交
    • L
      pinctrl: rename U300 and SIRF pin controllers · 3bece55a
      由 Linus Walleij 提交于 
      For stringent order, rename the pinmux-* pin controllers to
pinctrl-* and also rename the Kconfig symbols and in-kernel
users.

Cc: Rongjun Ying <Rongjun.Ying@csr.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      3bece55a
    • L
      pinctrl: add a pin config interface · ae6b4d85
      由 Linus Walleij 提交于 
      This add per-pin and per-group pin config interfaces for biasing,
driving and other such electronic properties. The details of passed
configurations are passed in an opaque unsigned long which may be
dereferences to integer types, structs or lists on either side
of the configuration interface.

ChangeLog v1->v2:
- Clear split of terminology: we now have pin controllers, and
  those may support two interfaces using vtables: pin
  multiplexing and pin configuration.
- Break out pin configuration to its own C file, controllers may
  implement only config without mux, and vice versa, so keep each
  sub-functionality of pin controllers separate. Introduce
  CONFIG_PINCONF in Kconfig.
- Implement some core logic around pin configuration in the
  pinconf.c file.
- Remove UNKNOWN config states, these were just surplus baggage.
- Remove FLOAT config state - HIGH_IMPEDANCE should be enough for
  everyone.
- PIN_CONFIG_POWER_SOURCE added to handle switching the power
  supply for the pin logic between different sources
- Explicit DISABLE config enums to turn schmitt-trigger,
  wakeup etc OFF.
- Update documentation to reflect all the recent reasoning.
ChangeLog v2->v3:
- Twist API around to pass around arrays of config tuples instead
  of (param, value) pairs everywhere.
- Explicit drive strength semantics for push/pull and similar
  drive modes, this shall be the number of drive stages vs
  nominal load impedance, which should match the actual
  electronics used in push/pull CMOS or TTY totempoles.
- Drop load capacitance configuration - I probably don't know
  what I'm doing here so leave it out.
- Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to
  PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off.
- Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined
  argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead.
- Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use
  PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off.
- Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time
  on input lines.
- Fix a bug when we tried to configure pins for pin controllers
  without pinconf support.
- Initialized debugfs properly so it works.
- Initialize the mutex properly and lock around config tampering
  sections.
- Check the return value from get_initial_config() properly.
ChangeLog v3->v4:
- Export the pin_config_get(), pin_config_set() and
  pin_config_group() functions.
- Drop the entire concept of just getting initial config and
  keeping track of pin states internally, instead ask the pins
  what state they are in. Previous idea was plain wrong, if the
  device cannot keep track of its state, the driver should do
  it.
- Drop the generic configuration layout, it seems this impose
  too much restriction on some pin controllers, so let them do
  things the way they want and split off support for generic
  config as an optional add-on.
ChangeLog v4->v5:
- Introduce two symmetric driver calls for group configuration,
  .pin_config_group_[get|set] and corresponding external calls.
- Remove generic semantic meanings of return values from config
  calls, these belong in the generic config patch. Just pass the
  return value through instead.
- Add a debugfs entry "pinconf-groups" to read status from group
  configuration only, also slam in a per-group debug callback in
  the pinconf_ops so custom drivers can display something
  meaningful for their pins.
- Fix some dangling newline.
- Drop dangling #else clause.
- Update documentation to match the above.
ChangeLog v5->v6:
- Change to using a pin name as parameter for the
  [get|set]_config() functions, as suggested by Stephen Warren.
  This is more natural as names will be what a developer has
  access to in written documentation etc.
ChangeLog v6->v7:
- Refactor out by-pin and by-name get/set functions, only expose
  the by-name functions externally, expose the by-pin functions
  internally.
- Show supported pin control functionality in the debugfs
  pinctrl-devices file.
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      ae6b4d85
    • L
      pinctrl: move the U300 GPIO driver to pinctrl · ca402d37
      由 Linus Walleij 提交于 
      This driver will be converted to a dual GPIO + pinctrl driver
since it supports biasing and driving control options. Hopefully
it can serve as an example.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      ca402d37