The AM572x-IDK board is a board based on TI's AM5728 SOC
which has a dual core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5728

This patch creates a common dtsi file that will provide a common board
dtsi file to define the nodes that are common to AM57xx (including the
upcoming AM5718) IDK boards.

Initial support is only for basic peripherals
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

TI's Industrial Communication Engine EVM is a low cost hardware mainly
developed for industrial communication type applications using serial
or Ethernet based interfaces. This platform features TI's AM3359 with
800MHz single core Cortex-A8 processor, 256MB DDR3, 64MB SPI flash,
8MB NOR Flash, mmc, usb, can, dual Ethernet ports.

For more information, look at HW user guide[1], Data manual[2].

Just add basic support for the moment.

[1] http://processors.wiki.ti.com/index.php/AM335x_Industrial_Communication_Engine_EVM_Rev2_1_HW_User_Guide
[2] http://www.ti.com/lit/ds/symlink/am3359.pdfSigned-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When possible generic node names should be used. So change the node name
from ehrpwm to pwm.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The binding definition for the PCF857x GPIO expanders doesn't mention
a "ti,pcf8575" compatible string.  This is apparently because TI is
only a second source - there is no functional difference between
PCF8575 chips manufactured by TI and NXP, and the same board might be
populated with either depending on availability.

This is not a problem in practice because the I2C core uses
of_modalias_node() before matching drivers and this strips the
manufacturer name.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NFilip Matijević <filip.matijevic.pz@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NFilip Matijević <filip.matijevic.pz@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Like the Nokia N900, the N950 has leds to show
the state of sys_clkreq and sys_off_mode pins.

A detailed description for the LEDs and
OMAP's sleep states can be found in Tony's
commit for the Nokia N900:

c1be2032Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add keypad matrix information based on data from
Nokia N950 Kernel.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add regulator configuration as found in the
board files of Nokia's kernel.
Signed-off-By: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The switch configuration for NAND is actually the other way round.
Also mention ON/OFF states as that is more natural to understand
(without the help of schematics) when compared to HIGH/LOW.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Few regulators information were missing from DT. Add those
missing regulators.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the DT node for Timer12 present on DRA7 family of
SoCs. Timer12 is present in PD_WKUPAON power domain, and
has the same capabilities as the other timers, except for
the fact that it serves as a secure timer on HS devices
and is clocked only from the secure 32K clock.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Timers 13 through 16 have been added previously in
disabled state. These timers are common timers that are
present on all DRA7 family of SoCs, so enable these
devices by default like the rest of the DMTimers.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add nodes to represent all McASP ports in the dra7 family.
For system consistency use the eDMA for audio operations. sDMA would be
fine for 4/5/6/7/8 since their DAT port is not through L3 interconnect.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

rename the mcasp8_ahclk_mux to mcasp8_ahclkx_mux.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for the unit offsets]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since we switched to use eDMA we can now safely enable the FIFO in McASP.
This will reduce the chance of McASP level under/overflow.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The assigned-clock* needs to be in the root of the device's node. If it is
in the sub-node the CCF will ignore it.
Since the clkout2 is used by the codec as MCLK, move the clock parent
selection to that node.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since we switched to use eDMA we can now safely enable the FIFO in McASP.
This will reduce the chance of McASP level under/overflow.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since we switched to use eDMA we can now safely enable the FIFO in McASP.
This will reduce the chance of McASP level under/overflow.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McASP3 does not support constant addressing mode on the DAT
port, so increment transfers must be used instead.  This
restriction is also applicable for McASP1 and McASP2.

This DMA addressing constraint poses a major problem for sDMA
where constant addressing mode is used on the peripheral side.
Unfortunately, using increment transfers in sDMA comes with
important side effects.

The addressing mode used in eDMA is INC, so the silicon limitation
described above has no impact and the McASP3 DAT port can be
safely added by switching to eDMA instead of sDMA.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DRA7 family has eDMA available along with the sDMA and in some cases it is
better suited for servicing peripherals.

Add the needed nodes for eDMA to be usable:
edma-tpcc, edma-tptc0/1 and the edma-xbar.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the sDMA xbar nodes under the L4 interconnect node.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP5 clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for DRA7 clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for DM81x clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for AM43xx clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for AM33xx clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP4 clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP2 clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP3 clock nodes:

Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"bandgap has a reg or ranges property, but no unit name"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warning:

"sound@0 has a unit name, but no reg property"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"pmu has a reg or ranges property, but no unit name"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"i2c@0 has a unit name, but no reg property"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"pbias_regulator has a reg or ranges property, but no unit name"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Pull Ceph updates from Sage Weil:
 "There is quite a bit here, including some overdue refactoring and
  cleanup on the mon_client and osd_client code from Ilya, scattered
  writeback support for CephFS and a pile of bug fixes from Zheng, and a
  few random cleanups and fixes from others"

[ I already decided not to pull this because of it having been rebased
  recently, but ended up changing my mind after all.  Next time I'll
  really hold people to it.  Oh well.   - Linus ]

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (34 commits)
  libceph: use KMEM_CACHE macro
  ceph: use kmem_cache_zalloc
  rbd: use KMEM_CACHE macro
  ceph: use lookup request to revalidate dentry
  ceph: kill ceph_get_dentry_parent_inode()
  ceph: fix security xattr deadlock
  ceph: don't request vxattrs from MDS
  ceph: fix mounting same fs multiple times
  ceph: remove unnecessary NULL check
  ceph: avoid updating directory inode's i_size accidentally
  ceph: fix race during filling readdir cache
  libceph: use sizeof_footer() more
  ceph: kill ceph_empty_snapc
  ceph: fix a wrong comparison
  ceph: replace CURRENT_TIME by current_fs_time()
  ceph: scattered page writeback
  libceph: add helper that duplicates last extent operation
  libceph: enable large, variable-sized OSD requests
  libceph: osdc->req_mempool should be backed by a slab pool
  libceph: make r_request msg_size calculation clearer
  ...

Pull orangefs filesystem from Mike Marshall.

This finally merges the long-pending orangefs filesystem, which has been
much cleaned up with input from Al Viro over the last six months.  From
the documentation file:

 "OrangeFS is an LGPL userspace scale-out parallel storage system.  It
  is ideal for large storage problems faced by HPC, BigData, Streaming
  Video, Genomics, Bioinformatics.

  Orangefs, originally called PVFS, was first developed in 1993 by Walt
  Ligon and Eric Blumer as a parallel file system for Parallel Virtual
  Machine (PVM) as part of a NASA grant to study the I/O patterns of
  parallel programs.

  Orangefs features include:

    - Distributes file data among multiple file servers
    - Supports simultaneous access by multiple clients
    - Stores file data and metadata on servers using local file system
      and access methods
    - Userspace implementation is easy to install and maintain
    - Direct MPI support
    - Stateless"

see Documentation/filesystems/orangefs.txt for more in-depth details.

* tag 'ofs-pull-tag-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux: (174 commits)
  orangefs: fix orangefs_superblock locking
  orangefs: fix do_readv_writev() handling of error halfway through
  orangefs: have ->kill_sb() evict the VFS side of things first
  orangefs: sanitize ->llseek()
  orangefs-bufmap.h: trim unused junk
  orangefs: saner calling conventions for getting a slot
  orangefs_copy_{to,from}_bufmap(): don't pass bufmap pointer
  orangefs: get rid of readdir_handle_s
  ornagefs: ensure that truncate has an up to date inode size
  orangefs: move code which sets i_link to orangefs_inode_getattr
  orangefs: remove needless wrapper around GFP_KERNEL
  orangefs: remove wrapper around mutex_lock(&inode->i_mutex)
  orangefs: refactor inode type or link_target change detection
  orangefs: use new getattr for revalidate and remove old getattr
  orangefs: use new getattr in inode getattr and permission
  orangefs: use new orangefs_inode_getattr to get size in write and llseek
  orangefs: use new orangefs_inode_getattr to create new inodes
  orangefs: rename orangefs_inode_getattr to orangefs_inode_old_getattr
  orangefs: remove inode->i_lock wrapper
  orangefs: put register_chrdev immediately before register_filesystem
  ...