1. 21 7月, 2015 1 次提交
  2. 30 6月, 2015 1 次提交
  3. 24 6月, 2015 1 次提交
    • A
      stmmac: troubleshoot unexpected bits in des0 & des1 · f1590670
      Alexey Brodkin 提交于
      Current implementation of descriptor init procedure only takes
      care about setting/clearing ownership flag in "des0"/"des1"
      fields while it is perfectly possible to get unexpected bits
      set because of the following factors:
      
       [1] On driver probe underlying memory allocated with
           dma_alloc_coherent() might not be zeroed and so
           it will be filled with garbage.
      
       [2] During driver operation some bits could be set by SD/MMC
           controller (for example error flags etc).
      
      And unexpected and/or randomly set flags in "des0"/"des1"
      fields may lead to unpredictable behavior of GMAC DMA block.
      
      This change addresses both items above with:
      
       [1] Use of dma_zalloc_coherent() instead of simple
           dma_alloc_coherent() to make sure allocated memory is
           zeroed. That shouldn't affect performance because
           this allocation only happens once on driver probe.
      
       [2] Do explicit zeroing of both "des0" and "des1" fields
           of all buffer descriptors during initialization of
           DMA transfer.
      
      And while at it fixed identation of dma_free_coherent()
      counterpart as well.
      Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
      Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
      Cc: arc-linux-dev@synopsys.com
      Cc: linux-kernel@vger.kernel.org
      Cc: stable@vger.kernel.org
      Cc: David Miller <davem@davemloft.net>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f1590670
  4. 23 6月, 2015 4 次提交
  5. 18 6月, 2015 1 次提交
  6. 31 5月, 2015 3 次提交
  7. 26 5月, 2015 1 次提交
    • M
      net: stmmac: create one debugfs dir per net-device · 466c5ac8
      Mathieu Olivari 提交于
      stmmac DebugFS entries are currently global to the driver. As a result,
      having more than one stmmac device in the system creates the following
      error:
      * ERROR stmmaceth, debugfs create directory failed
      * stmmac_hw_setup: failed debugFS registration
      
      This also results in being able to access the debugfs information for
      the first registered device only.
      
      This patch changes the debugfs structure to have one sub-directory per
      net-device. Files under "/sys/kernel/debug/stmmaceth" will now show-up
      under /sys/kernel/debug/stmmaceth/ethN/.
      Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      466c5ac8
  8. 22 5月, 2015 5 次提交
  9. 16 5月, 2015 10 次提交
  10. 04 5月, 2015 1 次提交
  11. 17 4月, 2015 5 次提交
  12. 10 4月, 2015 1 次提交
  13. 09 4月, 2015 1 次提交
  14. 01 4月, 2015 2 次提交
  15. 09 3月, 2015 2 次提交
  16. 05 3月, 2015 1 次提交
    • A
      stmmac: check IRQ availability early on probe · 8f02d8da
      Alexey Brodkin 提交于
      Currently we're getting IRQs after lots of resources are already
      allocated:
       * netdev
       * clocks
       * MDIO bus
      Also HW gets initialized by the time when checking IRQs as well.
      
      Now there's a possibility for master interrupt controller to be not
      probed yet. This will lead to exit from GMAC probe routine with "-
      EPROBE_DEFER" and so deferred probe will hapen later on.
      
      But since we exited the first GMAC probe without release of all
      allocated resources there could be conflicts on subsequent probes.
      
      For example this is what happens for me:
       --->8---
       stmmaceth e0018000.ethernet: no reset control found
       stmmac - user ID: 0x10, Synopsys ID: 0x37
        Ring mode enabled
        DMA HW capability register supported
        Normal descriptors
        RX Checksum Offload Engine supported (type 2)
        TX Checksum insertion supported
        Enable RX Mitigation via HW Watchdog Timer
       libphy: stmmac: probed
       eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
       platform e0018000.ethernet: Driver stmmaceth requests probe deferral
       ...
       ...
       ...
       stmmaceth e0018000.ethernet: no reset control found
       stmmac - user ID: 0x10, Synopsys ID: 0x37
        Ring mode enabled
        DMA HW capability register supported
        Normal descriptors
        RX Checksum Offload Engine supported (type 2)
        TX Checksum insertion supported
        Enable RX Mitigation via HW Watchdog Timer
       ------------[ cut here ]------------
       WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
       sysfs: cannot create duplicate filename
      '/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
       CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
       Workqueue: deferwq deferred_probe_work_func
      
       Stack Trace:
        arc_unwind_core+0xb8/0x114
        warn_slowpath_common+0x5a/0x8c
        warn_slowpath_fmt+0x2e/0x38
        sysfs_warn_dup+0x4e/0x68
        sysfs_create_dir_ns+0x98/0xa0
        kobject_add_internal+0x8c/0x2e8
        kobject_add+0x4a/0x8c
        device_add+0xc6/0x448
        mdiobus_register+0x6c/0x164
        stmmac_mdio_register+0x112/0x264
        stmmac_dvr_probe+0x6c0/0x85c
        stmmac_pltfr_probe+0x2e4/0x50c
        platform_drv_probe+0x26/0x5c
        really_probe+0x76/0x1dc
        bus_for_each_drv+0x42/0x7c
        device_attach+0x64/0x6c
        bus_probe_device+0x74/0xa4
        deferred_probe_work_func+0x50/0x84
        process_one_work+0xf8/0x2cc
        worker_thread+0x110/0x478
        kthread+0x8a/0x9c
        ret_from_fork+0x14/0x18
       ---[ end trace a2dfaa7d630c8be1 ]---
       ------------[ cut here ]------------
       WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
      kobject_add_internal+0x218/0x2e8()
       kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
      register things with the same name in the same di.
       CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W
      4.0.0-rc1-next-20150303+ #8
       Workqueue: deferwq deferred_probe_work_func
      
       Stack Trace:
        arc_unwind_core+0xb8/0x114
        warn_slowpath_common+0x5a/0x8c
        warn_slowpath_fmt+0x2e/0x38
        kobject_add_internal+0x218/0x2e8
        kobject_add+0x4a/0x8c
        device_add+0xc6/0x448
        mdiobus_register+0x6c/0x164
        stmmac_mdio_register+0x112/0x264
        stmmac_dvr_probe+0x6c0/0x85c
        stmmac_pltfr_probe+0x2e4/0x50c
        platform_drv_probe+0x26/0x5c
        really_probe+0x76/0x1dc
        bus_for_each_drv+0x42/0x7c
        device_attach+0x64/0x6c
        bus_probe_device+0x74/0xa4
        deferred_probe_work_func+0x50/0x84
        process_one_work+0xf8/0x2cc
        worker_thread+0x110/0x478
        kthread+0x8a/0x9c
        ret_from_fork+0x14/0x18
       ---[ end trace a2dfaa7d630c8be2 ]---
       libphy: mii_bus stmmac-0 failed to register
       : Cannot register as MDIO bus
       stmmac_pltfr_probe: main driver probe failed
       stmmaceth: probe of e0018000.ethernet failed with error -22
       --->8---
      
      Essential fix is to check for IRQs availability as early as possible and
      then safely go to deferred probe if IRQs are not there yet.
      Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
      Cc: Vineet Gupta <vgupta@synopsys.com>
      Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
      Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
      Cc: Sonic Zhang <sonic.zhang@analog.com>
      Cc: David S. Miller <davem@davemloft.net>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8f02d8da