added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c

AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB.  datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdfSigned-off-by: NRadek Liboska <liboska@uochb.cas.cz>

I notice that the processcompl_compat() function seems to be leaking the
'struct async *as' in the error paths. 

I think that the calling convention is fundamentally buggered. The
caller is the one that did the "reap_as()" to get the as thing, the
caller should be the one to free it too. 

Freeing it in the caller also means that it very clearly always gets
freed, and avoids the need for any "free in the error case too".

From: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Marcus Meissner <meissner@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need to only copy the data received by the device to userspace, not
the whole kernel buffer, which can contain "stale" data.

Thanks to Marcus Meissner for pointing this out and testing the fix.
Reported-by: NMarcus Meissner <meissner@suse.de>
Tested-by: NMarcus Meissner <meissner@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:

  r8a66597_timer() <-- lock taken
    r8a66597_root_hub_control()
      r8a66597_check_syssts()
        usb_hcd_poll_rh_status() <-- acquires the same lock
	/* insert death here */

The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>

This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:

    When the HDC driver writes the data to the transfer buffers it
    pollutes the D-cache (unlike DMA drivers where the device writes
    the data). If the corresponding pages get mapped into user space,
    there are no additional cache flushing operations performed and
    this causes random user space faults on architectures with
    separate I and D caches (Harvard) or those with aliasing D-cache.

This fixes up crashes during USB boot on SH7724 and others:

	http://marc.info/?l=linux-sh&m=126439837308912&w=2Reported-by: NGoda Yusuke <goda.yusuke@renesas.com>
Tested-by: NGoda Yusuke <goda.yusuke@renesas.com>
Cc: stable@kernel.org
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>

This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There was some left over #ifdef ARM logic that is outdated but no one
really noticed.  So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings.  So use %zu for sizeof() values.  This is a
better version of the previous commit b0a9cf29.
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Resolves kernel.org bug 14914.

Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).

The patch works, but let me clarify a few things about it.  All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think).  I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear.  Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine.  Starting with
2.6.30, things no longer work.
Signed-off-by: NRyan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Assign fhci only if usb is not NULL.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate.  It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:

[  427.681810] Restarting tasks ...
[  427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[  427.682019] usb usb3: usb resume
[  427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[  427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[  427.682205] usb 1-2: usb wakeup-resume
[  427.682226] usb 1-2: finish reset-resume
[  427.682886] done.
[  427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[  427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[  427.746682] hub 3-0:1.0: hub_reset_resume
[  427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[  427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[  427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[  427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[  427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[  427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[  427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[  427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[  427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[  427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[  427.916609]  ep_81: create, parent hub
[  427.916632] ------------[ cut here ]------------
[  427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[  427.916649] Hardware name: System Product Name
[  427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[  427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[  427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869aa-dirty #13
[  427.916699] Call Trace:

The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.

After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces.  However, the
USB core keeps track of the old state, which may include non-zero
alternate settings.  It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.

The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0.  This caused duplicate
endpoint files to be created.

The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device().  Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NBorislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: NKurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1330) fixes a bug in khbud's handling of remote
wakeups.  When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes.  At
this point the port's SUSPEND feature is automatically turned off.

However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec).  Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup.  This patch adds the missing
delay to the remote-wakeup path.

It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes).  The extra time appears to help some
devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost.  When remote wakeup is
enabled, this is undesirable behavior.

The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.

	URBs with an interval of 2 or 4 microframes aren't handled.
	For the time being, the patch reduces to interval to 1 uframe.

	URBs are constrained to have an interval no larger than 1024
	frames by usb_submit_urb().  But some EHCI controllers allow
	use of a schedule as short as 256 frames; for these
	controllers we may have to decrease the interval to the
	actual schedule length.

The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames.  But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: NGlynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a regression introduced by commit
715b1dc0 ("USB: usb_debug,
usb_generic_serial: implement multi urb write").

URB transfer buffer was never freed when using multi-urb writes. 
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: NJason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.

Please apply it to the 2.6.33-rc* tree.
Signed-off-by: NStefani Seibold <stefani@seibold.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.

Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.

Fixed that.  Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: Npancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I made this patch for usbserial driver to add the support for EVDO modem
Haier CE100. The bugs report for this is here:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/490068

This patch based on these post:
http://blankblondtank.wordpress.com/2009/09/04/mengoptimalkan-koneksi-modem-haier-ce-100-cdma-di-linux/
http://tantos.web.id/blogs/how-to-internet-connection-using-cdma-evdo-modem-and-karmic-koala-ubuntu-9-10

I hope this patch can help other that have the Haier C100 modem, mostly in my country, Indonesia.
Signed-off-by: NDonny Kurnia <donnykurnia@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The wTotalLength should contain the sum of the interface and unit
descriptor sizes per the Audio Device Class specification 1.0.
Reported-by: NSergey Lapin <slapin@ossfans.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

commit 91c8a5a9 broke
compilation of this driver after it introduced
otg_init() as a static inline in <linux/usb/otg.h>
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some of these workarounds are already in place, but labeled as affecting
all BF52x parts.  Since we have official anomaly numbers now, use those
defines.  And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below array index out of bounds issue.

Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84

The data stored in 'aInfo' array exceeds the array size of 78.

This patch increases the size of this array to hold the string
correctly without any memory corruption.

This issue was reported by Klockwork tool.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the following NULL pointer dereference issue.

Pointer 'request' returned from call to function 'next_request'
at line 748 may be NULL and may be dereferenced at line 792.

============
Code Snippet
============

748:  request = next_request(musb_ep);
785: if (dma && (csr & MUSB_RXCSR_DMAENAB)) {
	csr &= ~(MUSB_RXCSR_AUTOCLEAR
			| MUSB_RXCSR_DMAENAB
			| MUSB_RXCSR_DMAMODE);
	musb_writew(epio, MUSB_RXCSR,
		MUSB_RXCSR_P_WZC_BITS | csr);

792:	 request->actual += musb_ep->dma->actual_len;
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since a DMA transfer may need to be kicked off several times to complete,
the DMA start must include the length that has already been transferred.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gadget stalling a zero-length SETUP request results in this error message:

SetupEnd came in a wrong ep0stage idle

In order to avoid it, always set the CSR0.DataEnd bit after detecting a zero-
length request.  Add the missing '\n' to the error message itself as well...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Race condition exists between the cppi_interrupt handler and
davinci_interrupt handler w.r.t completing a TX IO.  Since DM646x
has seperate DMA and USB endpoint interrupts cppi_interrupt handler
needs to hold the lock while operating on the endpoint.

Update over previous patch to avoid taking the lock if already
taken.  Tested on DM644x, DM355 and DM646x platforms.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When registering gadget driver, the state of the transceiver
must be set from undefined (no gadget) to b_idle.

Module unload sets the transceiver state to undefined state.
After the first load/unload pair, the reset irq will be lost.
Signed-off-by: NArnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a null-pointer dereference bug.
Signed-off-by: NSwaminathan S <swami.iyer@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current musb gadget dma code produces the warning:
drivers/usb/musb/musb_gadget.c: In function 'txstate':
drivers/usb/musb/musb_gadget.c:312: warning: comparison of distinct
                                             pointer types lacks a cast

So switch to min_t(size_t, ...).
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

probe() already was on __init, so moving remove() to __exit.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 7723de7e (USB: musb_gadget: remove
pointless loop) included uncalled for (and incorrect) optimization that
might cause a kernel oops in txstate() -- undo it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.

Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.

Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).

Compile-tested, based on latest mainline git.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix new kernel-doc warnings in usb core:

Warning(drivers/usb/core/usb.c:79): No description found for parameter 'config'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'iface_num'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'alt_num'
Warning(drivers/usb/core/hcd.c:1622): No description found for parameter 'udev'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>