This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Re-organized and cleaned up the ISP82xx specific code.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NHarish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This function was added to encapsulate freeing the memory for all the fcports
associated with a particular vha.  Also added a call to qla2x00_free_fcports()
to qla2x00_free_device() to free the memory for all the fcports associated with
a vha during device removal.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If BIOS is enabled then drivers init firmware fails since
BIOS has done the init once.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Earlier implementation did not take into account the varying
sizes of data buffers returned from structures sts_entry_t and
sts_entry_24xx.  Sense-data after the 20th byte could be
incorrect.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The default method that qla2xxx uses is the GID_PT nameserver command to
get a list of Nx_Ports. This patch adds a GFF_ID call for each port
returned by GID_PT to get the FC4 type. If the FC4 type is not FCP SCSI
then the qla2xxx driver will not record that port in it's port database.
For switches that do not support the GFF_ID command, the behavior will be
for qla2xxx to store that port anyways.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: For ISP 23xx, select user specified login timeout value if greater than minuimum value(4 secs).
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Driver was not unprotecting correctly, use correct bits
to unprotect the flash on ISP 82xx.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Outstanding mailbox commands, have no way to recover on f/w hung, and we
timeout on waiting for mbx response. This in turn affects the recovery process
as follows:
- We might already be in dpc while waiting for mbx to complete, so recovery for
that pci function will never get invoked. Reset Timeout (10 sec) is far less
than mbx timeout (30 sec).
- Other mbx cmds will get stuck due to serial mbx access.

Solution is to identify fw-hung scenario and handle outstanding mbx commands to
have an early-exit instead of waiting for response.
Other mbx commands waiting for access will also do an early-exit if fw-hung is
still applicable.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

After topology change ISP is reset and VPs are re-enabled.
If the topology is not fabric, VPs could falsely get enabled.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Used bootloder address from FLT while loading FW from flash as well.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In case of both target and initiator capabilities reported by fc port,
the fc port port capability is made mutualy exclusive with priority given
for target capabilities.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

* hold the hardware_lock throughout the duration of ctx-sp
  timeout handling -- could result in use-after-free oops.

* retry a timed-out login-request.

* done() routines are called with the hardware-lock held, issue
qla2x00_mark_device_lost() with proper 'defer' flag.

* FCP2 capabilities are only relevant to target devices.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Hold a reference to the srb (sp) while aborting an I/O -- as the
I/O can/will complete from within the interrupt-context.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The TMFs used for pre-24xx ISPs incorrectly assumed 'cpu' tag
data could be valid.  These chips have no multi-q/cpu-affinity
support.  This corrects an oops seen on ISP23xx parts.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This helps to correlate submission/completion messages during
triaging.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The CRB drive active register is cleared when driver is unloaded
or when driver enters failed state.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

1) Allow transition to NEED RESET state only from READY state for ISP82xx.
2) Avoid infinite ISP aborts when chip reset fails.
3) Code cleanup to remove some of the unused debug code.
Signed-off-by: NLalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>