Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 11 9月, 2009 1 次提交
    • P
      powerpc: Fix bug where perf_counters breaks oprofile · a6dbf93a
      由 Paul Mackerras 提交于 
      Currently there is a bug where if you use oprofile on a pSeries
machine, then use perf_counters, then use oprofile again, oprofile
will not work correctly; it will lose the PMU configuration the next
time the hypervisor does a partition context switch, and thereafter
won't count anything.

Maynard Johnson identified the sequence causing the problem:
- oprofile setup calls ppc_enable_pmcs(), which calls
  pseries_lpar_enable_pmcs, which tells the hypervisor that we want
  to use the PMU, and sets the "PMU in use" flag in the lppaca.
  This flag tells the hypervisor whether it needs to save and restore
  the PMU config.
- The perf_counter code sets and clears the "PMU in use" flag directly
  as it context-switches the PMU between tasks, and leaves it clear
  when it finishes.
- oprofile setup, called for a new oprofile run, calls ppc_enable_pmcs,
  which does nothing because it has already been called.  In particular
  it doesn't set the "PMU in use" flag.

This fixes the problem by arranging for ppc_enable_pmcs to always set
the "PMU in use" flag.  It makes the perf_counter code call
ppc_enable_pmcs also rather than calling the lower-level function
directly, and removes the setting of the "PMU in use" flag from
pseries_lpar_enable_pmcs, since that is now done in its caller.

This also removes the declaration of pasemi_enable_pmcs because it
isn't defined anywhere.
Reported-by: NMaynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Cc: <stable@kernel.org)
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      a6dbf93a
  3. 21 5月, 2009 1 次提交
  5. 07 9月, 2008 1 次提交
  7. 26 8月, 2008 1 次提交
  9. 18 8月, 2008 1 次提交
  11. 25 7月, 2008 1 次提交
  13. 14 5月, 2008 1 次提交
  15. 24 4月, 2008 2 次提交
  17. 18 4月, 2008 3 次提交
  19. 17 4月, 2008 1 次提交
  21. 26 3月, 2008 1 次提交
  23. 03 12月, 2007 1 次提交
  25. 20 11月, 2007 1 次提交
    • L
      [POWERPC] Fix RTAS os-term usage on kernel panic · a2b51812
      由 Linas Vepstas 提交于 
      The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early.  Instead,
call it from the machine_reset() call.

This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().

Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero.  Calling os-term
helps keep the hypervisor happy!  We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      a2b51812
  27. 11 10月, 2007 1 次提交
  29. 22 7月, 2007 1 次提交
  31. 16 7月, 2007 1 次提交
  33. 14 6月, 2007 1 次提交
    • J
      [POWERPC] Donate idle CPU cycles on dedicated partitions · d8c391a5
      由 Jake Moilanen 提交于 
      A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).

This enables that to work properly on P6.

This just involves setting a bit in the CAS structure as well as the
VPA.  To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA.  Then call H_CEDE.

The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.

Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: NJake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      d8c391a5
  35. 07 5月, 2007 1 次提交
  37. 27 4月, 2007 1 次提交
  39. 13 4月, 2007 2 次提交
  41. 09 3月, 2007 1 次提交
  43. 17 2月, 2007 1 次提交
  45. 14 2月, 2007 3 次提交
  47. 09 12月, 2006 2 次提交
  49. 08 12月, 2006 1 次提交
  51. 04 12月, 2006 2 次提交
    • L
      [POWERPC] Wrap cpu_die() with CONFIG_HOTPLUG_CPU · 088df4d2
      由 Linas Vepstas 提交于 
      Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      088df4d2
    • B
      [POWERPC] Make pci_read_irq_line the default · f90bb153
      由 Benjamin Herrenschmidt 提交于 
      This patch reworks the way IRQs are fixed up on PCI for arch powerpc.

It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().

It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.

I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.

I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      f90bb153
  53. 07 10月, 2006 1 次提交
  55. 05 10月, 2006 1 次提交
    • D
      IRQ: Maintain regs pointer globally rather than passing to IRQ handlers · 7d12e780
      由 David Howells 提交于 
      Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.
Signed-Off-By: NDavid Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
      7d12e780
  57. 04 10月, 2006 1 次提交
  59. 03 10月, 2006 1 次提交
    • O
      [PATCH] restore parport_pc probing on powermac · 873ef76b
      由 Olaf Hering 提交于 
      The last change for partport_pc did fix the common case for all PowerMacs,
but it broke the case for PCI multiport IO cards.  In fact, the config
option CONFIG_PARPORT_PC_SUPERIO=y lead to a hard crash when cups probed
the parport driver.  It enables the winbond and smsc probing.

Remove the PARPORT_BASE check again, parport_pc_find_nonpci_ports() will
take care of it.  All powerpc configs should have
CONFIG_PARPORT_PC_SUPERIO=n, the code did not find anything on the chrp
boards we tested it on.

Tested on a G4/466 with a PCI card:

0001:10:13.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550])
        Subsystem: Timedia Technology Co Ltd Unknown device 5079
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 53
        Region 0: I/O ports at f2000800 [size=32]
        Region 2: I/O ports at f2000870 [size=8]
        Region 3: I/O ports at f2000860 [size=8]
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      873ef76b
  61. 02 10月, 2006 1 次提交
    • S
      [PATCH] namespaces: utsname: use init_utsname when appropriate · 96b644bd
      由 Serge E. Hallyn 提交于 
      In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use.  This patch replaces those with a the init_utsname
helper.

Changes: Removed several uses of init_utsname().  Hope I picked all the
	right ones in net/ipv4/ipconfig.c.  These are now changed to
	utsname() (the per-process namespace utsname) in the previous
	patch (2/7)

[akpm@osdl.org: CIFS fix]
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      96b644bd
  63. 01 10月, 2006 1 次提交
    • O
      [PATCH] update legacy io handling for pmac · 30cbc222
      由 Olaf Hering 提交于 
      ppc can boot one single binary on prep, chrp and pmac boards.  ppc64 can
boot one single binary on pseries and G5 boards.  pmac has no legacy io,
probing for PC style legacy hardware (or accessing the legacy io area
regulary) may lead to a hard crash:

* add check for parport_pc, exit on pmac.  32bit chrp has no
  ->check_legacy_ioport, the probe is always called.  64bit chrp has
  check_legacy_ioport, check for a "parallel" node

* add check for isapnp, only PReP boards may have real ISA slots.  32bit
  PReP will have no ->check_legacy_ioport, the probe is always called.

* update code in i8042_platform_init.  Run ->check_legacy_ioport first,
  always call request_region.  No functional change.  Remove whitespace
  before i8042_reset init.
Signed-off-by: NOlaf Hering <olaf@aepfle.de>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      30cbc222