This patch removes const qualifiers from instances of struct arm_pmu,
and functions initialising them, in preparation for generalising
arm_pmu usage to system (AKA uncore) PMUs.

This will allow for dynamically modifiable structures (locks,
struct pmu) to be added as members of struct arm_pmu.
Acked-by: NJamie Iles <jamie@jamieiles.com>
Reviewed-by: NJean Pihet <j-pihet@ti.com>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Add clock control support for sh7372 CMT hardware blocks.

No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.

This patch relies on the recently merged

 794d78fe drivers: sh: late disabling of clocks V2

to make sure the unused clocks get disabled as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add clock control support for sh7372 MSIOF hardware blocks.

No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.

This patch relies on the recently merged

 794d78fe drivers: sh: late disabling of clocks V2

to make sure the unused clocks get disabled as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

MAINCKSEL is [29:28], not [27:24]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.

The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.

Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.

If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register.  If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARM920 and ARM926 save four registers, not three.  Fix the size of
the suspend region required.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code.  Overwriting it is
not a good idea.

We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration.  So fix this latent bug.

This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.

If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes following building error:
--
arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_preinit':
arch/arm/mach-footbridge/dc21285.c:299:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-footbridge/dc21285.c:299:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
--
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

This patch fixed following building error:
--
arch/arm/mach-orion5x/pci.c: In function 'orion5x_pci_sys_setup':
arch/arm/mach-orion5x/pci.c:563:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-orion5x/pci.c:563:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-orion5x/pci.o] Error 1
make[1]: *** Waiting for unfinished jobs....
--
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Upstream commit d5341942 "PCI: Make the
struct pci_dev * argument of pci_fixup_irqs const." leaked an extra
"const" into an actual call site (vs a proto/decl) which causes this:

arch/arm/mach-orion5x/dns323-setup.c: In function 'dns323_pci_map_irq':
arch/arm/mach-orion5x/dns323-setup.c:80: error: expected expression before 'const'
arch/arm/mach-orion5x/dns323-setup.c:80: error: too few arguments to function 'orion5x_pci_map_irq'
make[3]: *** [arch/arm/mach-orion5x/dns323-setup.o] Error 1
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Acked-by: NRalf Baechle <ralf@linux-mips.org>

Commit c03f007a (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods.  Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.

Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Associate the HDMI clock together with LCDC1 on sh7372.

Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.

This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)

 794d78fe drivers: sh: late disabling of clocks V2

introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This was a typo in clockdev declaration for at91sam9261 SoC.
Fix the kernel hanging when switching clocksource to TC (tcb_clksrc).
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NRemy Bohmer <linux@bohmer.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

It seems that an entry for the SP805 watchdog in the table of clocks was
missing.  This results in the sp805_wdt driver rejecting the device with
the following errors:

  sp805-wdt mb:wdt: Clock not found
  sp805-wdt mb:wdt: Probe Failed!!!
  sp805-wdt: probe of mb:wdt failed with error -2

While not obviously stated in the hardware docs, the onboard SP810's
"REFCLK" is connected to a 32.768KHz crystal, and this drives the
watchdog.  Add a struct clk and corresponding lookup entry for it.
Signed-off-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

I made some changes to the entry in the ARM Machine Registry after
submission which was the wrong thing to do.
This patch should help to fix this error.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Should be passing the parent clk object when
calling for parent rate.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This is required to use SWRESET.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch increases reset delay from 50 usec to 80 usec for
USB HOST PHY. In order to reset USB HOST PHY controller properly,
a little extra time is required during its reset cycle.
Signed-off-by: NYulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds chained IRQ enter/exit functions to gpio interrupt
handler in order to function correctly on primary controllers with
different methods of flow control.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds chained IRQ enter/exit functions to external interrupt
handler in order to function correctly on primary controllers with
different methods of flow control.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds chained IRQ enter/exit functions to timer
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

When S3C_PM_DEBUG_LED_SMDK is enabled for suspend/resume debugging, the following
compilation error occurs:

arch/arm/mach-s3c64xx/pm.c: In function 's3c_pm_debug_smdkled':
arch/arm/mach-s3c64xx/pm.c:41: error: implicit declaration of function 'gpio_set_value'
arch/arm/mach-s3c64xx/pm.c:41: error: implicit declaration of function 'S3C64XX_GPN'
arch/arm/mach-s3c64xx/pm.c: In function 's3c64xx_pm_init':
arch/arm/mach-s3c64xx/pm.c:184: error: implicit declaration of function 'gpio_request'
arch/arm/mach-s3c64xx/pm.c:188: error: implicit declaration of function 'gpio_direction_output'

Fix the error by including linux/gpio.h
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Fixed the following warning for S5PV210.

arch/arm/mach-s5pv210/pm.c: In function 's5pv210_pm_add':
arch/arm/mach-s5pv210/pm.c:139: warning: assignment from
incompatible pointer type

Also, staticized the function.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This is a regression fix after migration to the external GIC.
The breakage has been introduced in commit 69644a8e
("ARM: EXYNOS4: modify interrupt mappings for external GIC")
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: added commit id]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Remove duplicated #include('s) in
  arch/arm/mach-exynos4/cpu.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Use the correct regulator names for cpufreq
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

WARNING: vmlinux.o(.text+0xf47c): Section mismatch in reference from the function samsung_bl_set() to the (unknown reference) .init.data:(unknown)
The function samsung_bl_set() references
the (unknown reference) __initdata (unknown).
This is often because samsung_bl_set lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to commit 659fb32d
("replace irq_gc_ack() with {set,clr}_bit variants"), this
should be fixed.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Since commit 8560a6cf
"arm: Footbridge: Use common i8253 clockevent",
ARCH_NETWINDER needs to select CLKEVT_I8253.

This patch fixes below build error with "make netwinder_defconfig".

  LD      .tmp_vmlinux1
arch/arm/mach-footbridge/built-in.o: In function `isa_timer_init':
isa-rtc.c:(.init.text+0x12c8): undefined reference to `clockevent_i8253_init'
isa-rtc.c:(.init.text+0x12d0): undefined reference to `i8253_clockevent'
arch/arm/mach-footbridge/built-in.o:(.data+0x198): undefined reference to `i8253_clockevent'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NSiarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.

The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.

It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the obvious error in board detection logic, because according to the TS's
manual, the model is stored in the least three significant bits. For example
the byte read on my ts-7300 is 0x23 and the detection then fails.

Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>