two reasons:
1. GPIO namings and their mode definitions are conceptually not part
   of the PXA register definitions

2. this is actually a temporary move in the transition of PXA2xx to
   use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
   code will still work and new code can be added in step by step
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

MFP configurations after resume should be done before the GPIO registers
are restored.  Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:

1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
   registers are already configured on pxa{25x,27x} while returns
   0 always on pxa3xx

2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
   ment of GPDRx, the side effect of this change is that the pin
   _must_ be configured before use, pxa_gpio_irq_type() will not
   change the pin to GPIO, as this restriction is sane, esp. with
   the new MFP framework
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

To further clean up the GPIO and IRQ structure:

1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
   function pxa_init_gpio()

2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
   an argument
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes the code better organized and simplified a bit.  The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.

This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable.  The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)

The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).

"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

by

1. wrapping long lines and making comments tidy

2. using IRQ_TYPE_* instead of migration macros __IRQT_*

3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
   stuff
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

by:

1. introduce dedicated pxa_{mask,unmask}_low_gpio()

2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
   initialized in pxa_init_irq()

3. introduce dedicated pxa_init_gpio_set_wake()
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. As David Brownell suggests, using ffs() is going to make the loop
   a bit faster (by avoiding unnecessary shift and iteration)

2. Russell suggested find_{first,next}_bit() being used with the
   gedr[] array
Signed-off-by: Neric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

While backporting 72dc67a6, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline).  This caused a page reference leak, resulting in a
fairly massive memory leak.

Fix by removing the extraneous gfn_to_page() call.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

init_rmode_tss was forgotten during the conversion from mmap_sem to
slots_lock.

INFO: task qemu-system-x86:3748 blocked for more than 120 seconds.
Call Trace:
 [<ffffffff8053d100>] __down_read+0x86/0x9e
 [<ffffffff8053fb43>] do_page_fault+0x346/0x78e
 [<ffffffff8053d235>] trace_hardirqs_on_thunk+0x35/0x3a
 [<ffffffff8053dcad>] error_exit+0x0/0xa9
 [<ffffffff8035a7a7>] copy_user_generic_string+0x17/0x40
 [<ffffffff88099a8a>] :kvm:kvm_write_guest_page+0x3e/0x5f
 [<ffffffff880b661a>] :kvm_intel:init_rmode_tss+0xa7/0xf9
 [<ffffffff880b7d7e>] :kvm_intel:vmx_vcpu_reset+0x10/0x38a
 [<ffffffff8809b9a5>] :kvm:kvm_arch_vcpu_setup+0x20/0x53
 [<ffffffff8809a1e4>] :kvm:kvm_vm_ioctl+0xad/0x1cf
 [<ffffffff80249dea>] __lock_acquire+0x4f7/0xc28
 [<ffffffff8028fad9>] vfs_ioctl+0x21/0x6b
 [<ffffffff8028fd75>] do_vfs_ioctl+0x252/0x26b
 [<ffffffff8028fdca>] sys_ioctl+0x3c/0x5e
 [<ffffffff8020b01b>] system_call_after_swapgs+0x7b/0x80
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

Do not assume that a shadow mapping will always point to the same host
frame number.  Fixes crash with madvise(MADV_DONTNEED).

[avi: move after first printk(), add another printk()]
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

is_rmap_pte() doesn't take into account io ptes, which have the avail bit set.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

The vmx hardware state restore restores the tss selector and base address, but
not its length.  Usually, this does not matter since most of the tss contents
is within the default length of 0x67.  However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted.  The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.

Fix by restoring the tss length.  Note that i386 had this working already.

Closes bugzilla 10246.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip.  Otherwise the driver won't find the device.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".

Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: NH. Peter Anvin <hpa@kernel.org>
Acked-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The "bestcomm-core" driver defines its of_match table as follows

static struct of_device_id mpc52xx_bcom_of_match[] = {
	{ .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", },
	{ .type = "dma-controller", .compatible = "mpc5200-bestcomm", },
	{},
};

so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property.  Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.

Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.

This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If the bestcomm initialization fails, calls to the task allocate
function should fail gracefully instead of oopsing with a NULL deref.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller.  init_ipic_sysfs() will crash in that case.
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On pSeries, the hypervisor doesn't let us map in the eHEA ethernet
adapter using 64k pages, and thus the ehea driver will fail if 64k
pages are configured.  This works around the problem by always
using 4k pages for ioremap on pSeries (but not on other platforms).
A better fix would be to check whether the partition could ever
have an eHEA adapter, and only force 4k pages if it could, but this
will do for 2.6.25.

This is based on an earlier patch by Tony Breeds.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Revert

commit f62f1fc9
Author: Yinghai Lu <yhlu.kernel@gmail.com>
Date:   Fri Mar 7 15:02:50 2008 -0800

    x86: reserve dma32 early for gart

The patch has a dependency on bootmem modifications which are not .25
material that late in the -rc cycle. The problem which is addressed by
the patch is limited to machines with 256G and more memory booted with
NUMA disabled. This is not a .25 regression and the audience which is
affected by this problem is very limited, so it's safer to do the
revert than pulling in intrusive bootmem changes right now.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Currently kernel images are limited to 8MB in size, and this causes
problems especially when enabling features that take up a lot of
kernel image space such as lockdep.

The code now will align the kernel image size up to 4MB and map that
many locked TLB entries.  So, the only practical limitation is the
number of available locked TLB entries which is 16 on Cheetah and 64
on pre-Cheetah sparc64 cpus.  Niagara cpus don't actually have hw
locked TLB entry support.  Rather, the hypervisor transparently
provides support for "locked" TLB entries since it runs with physical
addressing and does the initial TLB miss processing.

Fully utilizing this change requires some help from SILO, a patch for
which will be submitted to the maintainer.  Essentially, SILO will
only currently map up to 8MB for the kernel image and that needs to be
increased.

Note that neither this patch nor the SILO bits will help with network
booting.  The openfirmware code will only map up to a certain amount
of kernel image during a network boot and there isn't much we can to
about that other than to implemented a layered network booting
facility.  Solaris has this, and calls it "wanboot" and we may
implement something similar at some point.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

so use nodedata_phys directly.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

fix the bug reported here:

	http://bugzilla.kernel.org/show_bug.cgi?id=10232

use update_memory_range() instead of add_memory_range() directly
to avoid closing the gap.

( the new code only affects and runs on systems where the MTRR
  workaround triggers. )
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

we have seen a little problem in rebooting Dell Optiplex 745 with the
0KW626 board. Here is a small patch enabling reboot with this board,
which forces the default reboot path it into the BIOS reboot mode.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The fault_msg text is not explictly nul terminated now in startup
assembly. Do so by converting .ascii to .asciz.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

aperture_64.c takes a piece of memory and makes it into iommu
window... but such window may not be saved by swsusp -- that leads to
oops during hibernation.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Acked-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

this patch allows hpet=force on nVidia nForce 430 southbridge.
This patch was tested by me on my old Asus A8N-VM CSM (where bios does not
support hpet and does not advertise it via acpi entry). My nForce430 version:
lspci -nn | grep LPC
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260]
(rev a2)

Kernel 2.6.24.3 after patching and using hpet=force reports this:
dmesg | grep -i hpet
Kernel command line: root=/dev/sda8 ro vga=773 video=vesafb:mtrr:4,ywrap
vt.default_utf8=0 hpet=force
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
Time: hpet clocksource has been installed.

grep -i hpet /proc/timer_list
Clock Event Device: hpet
 set_next_event: hpet_legacy_next_event
 set_mode:       hpet_legacy_set_mode

grep Clock /proc/timer_list (before patching)
Clock Event Device: pit
Clock Event Device: lapic

grep Clock /proc/timer_list (after patching)
Clock Event Device: hpet
Clock Event Device: lapic
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

a system with 256 GB of RAM, when NUMA is disabled crashes the
following way:

Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Cannot allocate aperture memory hole (ffff8101c0000000,65536K)
Kernel panic - not syncing: Not enough memory for aperture
Pid: 0, comm: swapper Not tainted 2.6.25-rc4-x86-latest.git #33

Call Trace:
 [<ffffffff84037c62>] panic+0xb2/0x190
 [<ffffffff840381fc>] ? release_console_sem+0x7c/0x250
 [<ffffffff847b1628>] ? __alloc_bootmem_nopanic+0x48/0x90
 [<ffffffff847b0ac9>] ? free_bootmem+0x29/0x50
 [<ffffffff847ac1f7>] gart_iommu_hole_init+0x5e7/0x680
 [<ffffffff847b255b>] ? alloc_large_system_hash+0x16b/0x310
 [<ffffffff84506a2f>] ? _etext+0x0/0x1
 [<ffffffff847a2e8c>] pci_iommu_alloc+0x1c/0x40
 [<ffffffff847ac795>] mem_init+0x45/0x1a0
 [<ffffffff8479ff35>] start_kernel+0x295/0x380
 [<ffffffff8479f1c2>] _sinittext+0x1c2/0x230

the root cause is : memmap PMD is too big,
[ffffe200e0600000-ffffe200e07fffff] PMD ->ffff81383c000000 on node 0
almost near 4G..., and vmemmap_alloc_block will use up the ram under 4G.

solution will be:
1. make memmap allocation get memory above 4G...
2. reserve some dma32 range early before we try to set up memmap for all.
and release that before pci_iommu_alloc, so gart or swiotlb could get some
range under 4g limit for sure.

the patch is using method 2.
because method1 may need more code to handle SPARSEMEM and SPASEMEM_VMEMMAP

will get
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 264245736k/268959744k available (8484k kernel code, 4187464k reserved, 4004k data, 724k init)
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

We recently got some of the "Desktop Form Factor" Optiplex 745's in.  I
noticed that there's an entry for the SFF one's, but the BIOS model number
of the DFF differs from that of the SFF.  We have been reliably
experiencing the same (as far as I can tell) reboot bug as the SFF boxes.

Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>