Conflicts:
	MAINTAINERS
	drivers/net/wireless/iwlwifi/pcie/trans.c

14e4:432c is found on some bcm63xx devices. The device is working fine
with b43.
Reported-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MSI is enabled by default for most of the 4th generation
chips. Add this for AR9462 - this fixes PowerSave operation,
the chip was not entering Network-Sleep mode earlier.
With proper powering down of the MAC now, power consumption
in associated state is reduced considerably.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently 4 channels are scanned per scan command. if scan request
is issued by user during Tx traffic, radio will be out of channel
for "4 * per_chan_scan_time" for each scan command and will not be
able to receive Rx packets. This adds delay in data traffic. We can
minimize it by reducing number of channels scanned per scan command
in this scenario.

We can not always scan 1 channel per scan command due to limitation
of number of command buffers. So we add code to decide number of
channels scanned per scan command in associated state.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If scan operation is started when Tx traffic is already running,
driver locks Tx queue until it gets completed. With this logic
there is a delay for Tx packets.

This patch implements new approach to give Tx path higher priority
in this case. Driver internally sends multiple synchronous scan
commands to firmware when scan is requested by user. Now we will
make sure that Tx queue is empty everytime before sending next scan
command. If Tx queue isn't empty scan command will be postponsed by
20msec. This rule will be followed until Tx queue becomes empty or
timeout of 1 second happens. In case of timeout scan operation will
be aborted.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the scan time per channel for active scanning is set to
200ms. It takes quite a while to finsh scanning on all channels,
especially with a dual band configuration.

Change the per channel scan time settings to the following values:

passive scan: 110ms
active scan: 30ms
specific scan: 30ms

Above settings have been tested on x86 and arm platforms.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-eeprom.c

  CC      drivers/net/wireless/ti/wl18xx/main.o
drivers/net/wireless/ti/wl18xx/main.c: In function ‘wl18xx_conf_init’:
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘long unsigned int’ [-Wformat]
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 24398e39
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Wed Mar 28 10:58:36 2012 +0200

    mac80211: set HT channel before association

removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.

This exists starting with d646960f ("NFC: Initial LLCP support").
Signed-off-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.

This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:

Queue 2 stuck for 10000ms

This doesn't seem to fix the higher queues that get stuck
from time to time.

Cc: stable@vger.kernel.org [2.6.27+]
Reviewed-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

this patch fixes kernel Oops on "rmmod b43" if firmware was not loaded:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff8104e988>] drain_workqueue+0x25/0x142
PGD 153ac6067 PUD 153b82067 PMD 0
Oops: 0000 [#1] SMP
Signed-off-by: NOleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My patch

   iwlwifi: use correct released ucode version

did not correctly report supported firmware
for the 6035 device. This patch fixes it. The
minimum supported firmware version for 6035
is v6.

Also correct the minimum supported firmware
version for the 6000g2 series of devices.

Cc: stable@kernel.org
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add my new trees to the MAINTAINERS file
for the components that I maintain in the
new trees.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211_hwsim: Set IEEE80211_STAT_ACK flag when userspace indicates that the frame has been acknowledged.

The station fail average is not updated correctly since the
IEEE80211_STAT_ACK flag is not set when using wmediumd with
mac80211_hwsim. Set this flag when wmediumd indicates that the frame
was successfully transmitted (eventually).
Signed-off-by: NQasim Javed <qasimj@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix:

BUG: sleeping function called from invalid context at kernel/workqueue.c:2547
in_atomic(): 1, irqs_disabled(): 0, pid: 629, name: wpa_supplicant
2 locks held by wpa_supplicant/629:
 #0:  (rtnl_mutex){+.+.+.}, at: [<c08b2b84>] rtnl_lock+0x14/0x20
 #1:  (&trigger->leddev_list_lock){.+.?..}, at: [<c0867f41>] led_trigger_event+0x21/0x80
Pid: 629, comm: wpa_supplicant Not tainted 3.3.0-0.rc3.git5.1.fc17.i686
Call Trace:
 [<c046a9f6>] __might_sleep+0x126/0x1d0
 [<c0457d6c>] wait_on_work+0x2c/0x1d0
 [<c045a09a>] __cancel_work_timer+0x6a/0x120
 [<c045a160>] cancel_delayed_work_sync+0x10/0x20
 [<f7dd3c22>] rtl8187_led_brightness_set+0x82/0xf0 [rtl8187]
 [<c0867f7c>] led_trigger_event+0x5c/0x80
 [<f7ff5e6d>] ieee80211_led_radio+0x1d/0x40 [mac80211]
 [<f7ff3583>] ieee80211_stop_device+0x13/0x230 [mac80211]

Removing _sync is ok, because if led_on work is currently running
it will be finished before led_off work start to perform, since
they are always queued on the same mac80211 local->workqueue.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=795176Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem was found by Larry Finger:
http://marc.info/?l=linux-wireless&m=133702401700614&w=2

The problem is identical to the one for ipw2200 which is already fixed:
http://marc.info/?l=linux-wireless&m=133457257407196&w=2

[   17.766431] ------------[ cut here ]------------
[   17.766467] WARNING: at net/wireless/core.c:562 wiphy_register+0x34c/0x3c0 [cfg80211]()
[   17.766471] Hardware name: Latitude D600
[   17.766474] Modules linked in: ipw2100(+) libipw pcmcia cfg80211 ppdev parport_pc yenta_socket sr_mod pcmcia_rsrc parport iTCO_wdt cdrom sg rfkill pcmcia_
core lib80211 tg3 video button battery ac iTCO_vendor_support joydev shpchp pcspkr pciehp pci_hotplug autofs4 radeon ttm drm_kms_helper uhci_hcd ehci_hcd rtc
_cmos thermal drm hwmon i2c_algo_bit i2c_core processor usbcore usb_common ata_generic ata_piix ahci libahci libata
[   17.766525] Pid: 474, comm: modprobe Not tainted 3.4.0-rc7-wl+ #6
[   17.766528] Call Trace:
[   17.766541]  [<c066ad08>] ? printk+0x28/0x2a
[   17.766552]  [<c0230edd>] warn_slowpath_common+0x6d/0xa0
[   17.766563]  [<e0b253bc>] ? wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766573]  [<e0b253bc>] ? wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766578]  [<c0230f2d>] warn_slowpath_null+0x1d/0x20
[   17.766588]  [<e0b253bc>] wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766605]  [<e0b5b0d6>] ipw2100_wdev_init+0x196/0x1c0 [ipw2100]
[   17.766616]  [<e0b5d962>] ipw2100_pci_init_one+0x2b2/0x694 [ipw2100]
[   17.766632]  [<c047ce52>] local_pci_probe+0x42/0xb0
[   17.766637]  [<c047e2b0>] pci_device_probe+0x60/0x90
[   17.766645]  [<c0376de2>] ? sysfs_create_link+0x12/0x20
[   17.766654]  [<c050f1f6>] really_probe+0x56/0x2e0
[   17.766659]  [<c037636d>] ? create_dir+0x5d/0xa0
[   17.766667]  [<c0518c6b>] ? pm_runtime_barrier+0x3b/0xa0
[   17.766672]  [<c050f5e4>] driver_probe_device+0x44/0xa0
[   17.766677]  [<c047e227>] ? pci_match_device+0x97/0xa0
[   17.766681]  [<c050f6c9>] __driver_attach+0x89/0x90
[   17.766686]  [<c050f640>] ? driver_probe_device+0xa0/0xa0
[   17.766691]  [<c050da2a>] bus_for_each_dev+0x3a/0x70
[   17.766695]  [<c050ee6c>] driver_attach+0x1c/0x30
[   17.766699]  [<c050f640>] ? driver_probe_device+0xa0/0xa0
[   17.766704]  [<c050ea77>] bus_add_driver+0x187/0x280
[   17.766710]  [<c045b9cd>] ? kset_find_obj+0x2d/0x60
[   17.766715]  [<c047e2e0>] ? pci_device_probe+0x90/0x90
[   17.766719]  [<c047e2e0>] ? pci_device_probe+0x90/0x90
[   17.766724]  [<c050fb85>] driver_register+0x65/0x110
[   17.766729]  [<c047e09d>] __pci_register_driver+0x3d/0xa0
[   17.766738]  [<e09f705c>] ipw2100_init+0x5c/0x1000 [ipw2100]
[   17.766743]  [<c020110f>] do_one_initcall+0x2f/0x170
[   17.766749]  [<e09f7000>] ? 0xe09f6fff
[   17.766757]  [<c0287ce8>] sys_init_module+0xa8/0x210
[   17.766766]  [<c067a075>] syscall_call+0x7/0xb
[   17.766769] ---[ end trace 559898c6bb0d1c75 ]---
[   17.767093] ipw2100: probe of 0000:02:03.0 failed with error -5

This warning appears only if we apply Ben Hutchings' fix
http://marc.info/?l=linux-wireless&m=132720204412667&w=2
for the bug reported by Cesare Leonardi
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=656813
with cfg80211 warning during device registration
("cfg80211: failed to add phy80211 symlink to netdev!").

We separate device bring up and registration with network stack
to avoid the problem.
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't spew errors when we can't find the NVS file in wlcore. Instead
fail the wl12xx boot HW op if the NVS isn't found.

Take this opportunity to remove some dead code from register_hw()
which looks for the NVS again needlessly.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Give all wl18xx phy module paramters -1 as a default value, indicating
the paramter was not set. Add previous default values to the default
18xx priv conf structure.

Remove the board_type field from wl18xx priv. The field with the same
name inside the phy conf is good enough for our purposes.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params
structure. Remove it and replace the phy part of the wl18xx conf with the
FW bound structure. This allows us to set/override all members.

Increment the wlconf version to ensure compatibility with the new
structure
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries
accordingly.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This is supported by new FW versions (.88+).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Instead of using the hardcoded configuration structure, try to read it
from a "firmware" file called wl18xx-conf.bin.  If the file doesn't
exist, fall back to the hardcoded version.  If the file exists but is
illegal, bail out.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add conf file header structure, magic and version values and export
the entire conf struct in debugfs.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Since we are now going to export the conf structure and read it from a
file, it should be packed to avoid surprises with padding bytes.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Since we will export the conf structure as a file, we need to use well
defined types.  Instead of using enum, whose size may vary, use u8 for
bcn_filt_mode instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The conf structure is going to be exported to a file, so we should use
only well defined types.  bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Instead of parsing all the binary data returned by the firmware, we
should simply export the binary and let the userspace do the parsing.

This commit adds a new file to debugfs to do that.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics.  The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add support for an external 26 MHz crystal source.

[Changed wl->ref_clock to priv->ref_clock -- Luca.]
Signed-off-by: NGrant Erickson <marathon96@gmail.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.

[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]

[Make the pre_pkt_send operation optional -- Luca]
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).

[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
Signed-off-by: NOrit Brayer <orit@ti.com>
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

PG2 requires 4 new parameters that to be passed to the PHY.

Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.

[Make sure PG1 still gets the original struct - Arik]
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

PG2 has a unique chip id. It supports similar HW quirks.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>